warning YAMAHA XT660Z 2013 Service Manual

4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
5. Use spray oil as a universal clea-
ner to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry comple-
tely before storing or covering it.
EWA11131
Contaminants on the brakes or
tires can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent. Before riding at hig-
her speeds, test the motorcy-
cle’s braking performance and
cornering behavior.
ECA10800
Apply spray oil and wax spa-
ringly and make sure to wipe
off any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for
advice on what products to use.
Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from
the lens.
EAUM1902
Storage
Short-term
Always store your motorcycle in a
cool, dry place and, if necessary, pro-
tect it against dust with a porous
cover. Be sure the engine and the
exhaust system are cool before cove-
ring the motorcycle.
ECA10810
Storing the motorcycle in a
poorly ventilated room or cove-
ring it with a tarp, while it is still
wet, will allow water and humi-
dity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
NOTICE
NOTICE
WARNING
MOTORCYCLE CARE AND STORAGE
7-3
7

stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap
onto the spark plug, and then
place the spark plug on the
cylinder head so that the
electrodes are grounded.
(This will limit sparking during
the next step.)
d. Turn the engine over several
times with the starter. (This
will coat the cylinder wall with
oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING!
To prevent damage or injury
from sparking, make sure
to ground the spark plugelectrodes while turning the
engine over.
[EWA10951]
4. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degra-
ded in one spot.
6. Cover the muffler outlets with
plastic bags to prevent moisture
from entering them.
7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a
month. Do not store the battery in
an excessively cold or warm pla-
ce [less than 0 °C (30 °F) or more
than 30 °C (90 °F)]. For more
information on storing the bat-
tery, see page 6-29.
TIP
Make any necessary repairs before
storing the motorcycle.
MOTORCYCLE CARE AND STORAGE
7-4
7

Rear brake:Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4
Front suspension:Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
XT660Z 210.0 mm (8.26 in)
XT660ZA 160.0 mm (6.30 in)
Rear suspension:Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
XT660Z 200.0 mm (7.87 in)
XT660ZA 145.0 mm (5.71 in)
Electrical system:Ignition system:
TCI
Charging system:
AC magneto
Battery:Model:
GT9B-4
Voltage, capacity:
12 V, 8.0 Ah
Headlight:Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:Low beam headlight:
12 V, 55.0 W x 1
High beam headlight:
12 V, 55.0 W x 1
Tail/brake light:
LED
Front turn signal light:
12 V, 10.0 W x 2
Rear turn signal light:
12 V, 10.0 W x 2
Auxiliary light:
12 V, 5.0 W x 2
Meter lighting:
LED (backlight)
Neutral indicator light:
LED
High beam indicator light:
LED
Turn signal indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
ABS warning light (for ABS models):
LED
Immobilizer system indicator light:
LED
Fuses:Main fuse:
30.0 A
Headlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
10.0 A
Parking lighting fuse:
10.0 A
Radiator fan fuse:
7.5 A
Fuel injection system fuse:
10.0 A
ABS control unit fuse (for ABS models):
5.0 A
ABS motor fuse (for ABS models):
30.0 A
ABS solenoid fuse (for ABS models):
20.0 A
SPECIFICATIONS
8-3
8

INDEX
AABS (for ABS models)..............................3-12
ABS warning light (for ABS models) ..........3-5
Air filter element and check hose, replacing
and cleaning ..........................................6-15
Anti-theft alarm (optional) ..........................3-9
Auxiliary light bulb, replacing ...................6-34
BBattery......................................................6-29
Brake and clutch levers, checking and
lubricating ..............................................6-25
Brake fluid level, checking .......................6-21
Brake lever ...............................................3-11
Brake pedal ..............................................3-12
Brake pedal, checking and lubricating ....6-26
CCables, checking and lubricating ............6-25
Care............................................................7-1
Catalytic converters .................................3-16
Clutch lever ..............................................3-11
Clutch lever free play, adjusting...............6-20
Coolant.....................................................6-14
Coolant temperature warning light ............3-5
DDimmer switch .........................................3-10
Drive chain slack ......................................6-23
Drive chain, cleaning and lubricating.......6-24
EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil and oil filter element................6-11
Engine stop switch ..................................3-10
Engine trouble warning light ......................3-5
FFront and rear brake pads, checking ......6-21
Front fork, adjusting .................................3-17
Front fork, checking .................................6-27
Fuel ..........................................................3-14
Fuel consumption, tips for reducing ............5-
Fuel tank breather/overflow hose ............3-15
Fuel tank cap ...........................................3-13
Fuses, replacing .......................................6-31
HHandlebar switches ...................................3-9
Hazard switch ..........................................3-10
Headlight bulb, replacing .........................6-32
High beam indicator light...........................3-4
Horn switch ..............................................3-10
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-20
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-6
Indicator and warning lights ......................3-4
LLicense plate light bulb, replacing ...........6-34
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-1
Multi-function display ................................3-6
NNeutral indicator light.................................3-4
PPanels, removing and installing .................6-8Parking .......................................................5-4
Part locations .............................................2-1
Pass switch ..............................................3-10
RRear suspension, lubricating ...................6-27
SSafety information ......................................1-1
Seat ..........................................................3-16
Shift pedal ................................................3-11
Shifting .......................................................5-2
Shock absorber assembly, adjusting.......3-18
Sidestand .................................................3-19
Sidestand, checking and lubricating .......6-26
Spark plug, checking .................................6-9
Specifications.............................................8-1
Start switch ..............................................3-10
Starting the engine.....................................5-1
Steering, checking ...................................6-28
Storage.......................................................7-3
Supporting the motorcycle ......................6-35
Swingarm pivots, lubricating ...................6-27
TTail/brake light ..........................................6-33
Throttle cable free play, checking ............6-17
Tool kit ........................................................6-1
Troubleshooting .......................................6-38
Troubleshooting charts ............................6-40
Turn signal indicator light ...........................3-4
Turn signal light bulb, replacing ...............6-34
Turn signal switch ....................................3-10
VValve clearance ........................................6-17
Vehicle identification number .....................9-1