warning light YAMAHA XTZ125 2008 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2008, Model line: XTZ125, Model: YAMAHA XTZ125 2008Pages: 97, PDF Size: 3.32 MB
Page 32 of 97
4-2
4-2 NOTE:
Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be thoroughly accomplished
in a very short time; and the added safety it assures is more than worth the time involved. If any maintenance service or
adjustment is needed, consult the chart above to refer to the pages in which the service or adjustment is described.
1. The engine, exhaust pipe, and muffler will be very hot after the engine has been run.
Be careful not to touch them or to allow any clothing item to contact them during inspection or repair.
2. If any item is not working properly, have it inspected and repaired before operating the motorcycle.
ITEMROUTINE
PAGE
Sidestand
Fittings / FastenersCheck all chassi fittings and fasteners.
Tighten / Adjust, if necessary
Check fuel level / top up as required.
Fuel tank
Lights, signals and switches
BatteryCheck electrolyte level.
Replenish with “distilled water” if necessary.6-27
4-8 , 6-5
4-8 , 6-35 ~ 6-36
6-32 ~ 6-346-28
4-9
Check for proper operation
Front brake and clutch
lever pivotsCheck for smooth operation.
Lubricate if necessary
Check for smooth operation.
Lubricate if necessary
6-27 Check for smooth operation.
Lubricate if necessary Rear brake and shift pedal
shafts
WARNING:
NOTE:
Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be thoroughly accomplished
in a very short time; and the added safety it assures is more than worth the time involved. If any maintenance service or
adjustment is needed, consult the chart above to refer to the pages in which the service or adjustment is described.
1. The engine, exhaust pipe, and muffler will be very hot after the engine has been run.
Be careful not to touch them or to allow any clothing item to contact them during inspection or repair.
2. If any item is not working properly, have it inspected and repaired before operating the motorcycle.
ITEMROUTINE
PAGE
Sidestand
Fittings / FastenersCheck all chassi fittings and fasteners.
Tighten / Adjust, if necessary
Check fuel level / top up as required.
Fuel tank
Lights, signals and switches
BatteryCheck electrolyte level.
Replenish with “distilled water” if necessary.6-27
4-8 , 6-5
4-8 , 6-35 ~ 6-36
6-32 ~ 6-346-28
4-9
Check for proper operation
Front brake and clutch
lever pivotsCheck for smooth operation.
Lubricate if necessary
Check for smooth operation.
Lubricate if necessary
6-27 Check for smooth operation.
Lubricate if necessary Rear brake and shift pedal
shafts
WARNING:
Page 66 of 97
6-19
6-19
ADVERTENCIA
After adjusting the pedal height adjust brake pedal free
play.
2. Freeplay. The rear brake pedal free play should be adjusted to
20 ~ 30 mm (0.8 ~ 1.2 in) at the brake pedal end. Turn
the adjuster on the brake rod clockwise to reduce play
or counterclockwise to increase play.
ADVERTENCIA
Brake pedal free play should be checked whenever the
chain is adjusted or the rear wheel is removed and then
reinstalled.
If it is impossible to make proper adjustment, consult
a Yamaha dealer.
Check the operation of the brake light after adjusting
the rear brake.
1. Adjuster
a.Free play: 20 ~ 30 mm ( 0.8 ~ 1.2 in)
WARNING:
WARNING:
ADVERTENCIA
After adjusting the pedal height adjust brake pedal free
play.
2. Freeplay. The rear brake pedal free play should be adjusted to
20 ~ 30 mm (0.8 ~ 1.2 in) at the brake pedal end. Turn
the adjuster on the brake rod clockwise to reduce play
or counterclockwise to increase play.
ADVERTENCIA
Brake pedal free play should be checked whenever the
chain is adjusted or the rear wheel is removed and then
reinstalled.
If it is impossible to make proper adjustment, consult
a Yamaha dealer.
Check the operation of the brake light after adjusting
the rear brake.
1. Adjuster
a.Free play: 20 ~ 30 mm ( 0.8 ~ 1.2 in)
WARNING:
WARNING:
Page 82 of 97
6-35
6-35
Headlight bulb replacementThis motocycle this equipped with halogen bulb on its
headlight.
If the headlight bulb burns out, replace the bulb as follows:
1. Remove the cowling by loosing its bolts.
2. Loosen the bulb connectors.
ADVERTENCIA
Keep flammable products and your hands away from
the bulb while it is on, as it is hot. Do not touch the
bulb until it cools down
"
WARNING:
Headlight bulb replacementThis motocycle this equipped with halogen bulb on its
headlight.
If the headlight bulb burns out, replace the bulb as follows:
1. Remove the cowling by loosing its bolts.
2. Loosen the bulb connectors.
ADVERTENCIA
Keep flammable products and your hands away from
the bulb while it is on, as it is hot. Do not touch the
bulb until it cools down
"
WARNING:
Page 87 of 97
6-40
6-40
Rear wheel installationWhen installing the rear wheel, reverse the removal
procedures. Pay attention to the following points:
1. Be sure the slot in the brake shoe plate is fit over the
stopper on the rear arm.
2. Make sure the rear wheel axl is inserted from the right-
hand side and that the chain pullers are installed with
the punched side outward.
3. Adjust the drive chain.
4. Make sure the axle nut is properly torqued.
Axle nut torque:
80 N.m ( 8.0 Kgf.m, 58 lbf.ft)
5. Adjust the rear brake.(See page 6-18)
Check the operation of the brake light after adjusting
the rear brake
WARNING:
Rear wheel installationWhen installing the rear wheel, reverse the removal
procedures. Pay attention to the following points:
1. Be sure the slot in the brake shoe plate is fit over the
stopper on the rear arm.
2. Make sure the rear wheel axl is inserted from the right-
hand side and that the chain pullers are installed with
the punched side outward.
3. Adjust the drive chain.
4. Make sure the axle nut is properly torqued.
Axle nut torque:
80 N.m ( 8.0 Kgf.m, 58 lbf.ft)
5. Adjust the rear brake.(See page 6-18)
Check the operation of the brake light after adjusting
the rear brake
WARNING: