brake YAMAHA XV1900A 2013 Owner's Manual

MOTORCYCLE CARE AND STORAGE
7-2
7off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
●
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
●
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
●
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield. Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
TIPSalt sprayed on roads in the winter may
remain well into spring.1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. After drying the motorcycle, apply a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
U1CRE2E0.book Page 2 Monday, September 17, 2012 9:05 AM

MOTORCYCLE CARE AND STORAGE
7-3
7
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean- er to remove any remaining dirt.
5. Touch up minor paint damage caused by stones, etc.
6. Wax all painted and chrome-plat- ed surfaces. Avoid combination
cleaner waxes, many of which
contain abrasives that may mar
the paint or protective finish.
7. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11131
Contaminants on the brakes or tires
can cause loss of control.●
Make sure that there is no oil or
wax on the brakes or tires.
●
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
NOTICE
ECA10950
●
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
●
Never apply oil or wax to the
drive belt.
●
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
●
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP●
Consult a Yamaha dealer for ad-
vice on what products to use.
●
Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
EAU26282
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the motor-
cycle.NOTICE
ECA10810
●
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
●
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the “Care” section of this chapter.
U1CRE2E0.book Page 3 Monday, September 17, 2012 9:05 AM

SPECIFICATIONS
8-2
8
Gear ratio:1st:
2.375 (38/16)
2nd: 1.571 (33/21)
3rd: 1.160 (29/25)
4th:
0.929 (26/28)
5th: 0.800 (24/30)Chassis:Frame type:
Double cradle
Caster angle: 30.90 °
Trail: 152 mm (6.0 in)Front tire:Type:Tubeless
Size: 130/70R18M/C 63H
Manufacturer/model:
DUNLOP/D251F LRear tire:Type:Tubeless
Size:
190/60R17M/C 78H
Manufacturer/model: DUNLOP/D251
Loading:Maximum load:203 kg (448 lb)
(Total weight of rider, passenger, cargo and
accessories)Tire air pressure (measured on cold
tires):Loading condition:
0–90 kg (0–198 lb)
Front: 250 kPa (2.50 kgf/cm², 36 psi)
Rear: 280 kPa (2.80 kgf/cm², 41 psi)
Loading condition:
90–203 kg (198–448 lb)
Front: 250 kPa (2.50 kgf/cm², 36 psi)
Rear: 280 kPa (2.80 kgf/cm², 41 psi)Front wheel:Wheel type:Cast wheel
Rim size: 18M/C x MT4.00Rear wheel:Wheel type:Cast wheel
Rim size: 17M/C x MT5.50Unified brake system:Operation:Activated by rear brake
Front brake:Type:Dual disc brake
Operation:
Right hand operation
Specified brake fluid: DOT 4Rear brake:Type:
Single disc brake
Operation: Right foot operation
Specified brake fluid: DOT 4Front suspension:Type:Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
130.0 mm (5.12 in)Rear suspension:Type:Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel: 110.0 mm (4.33 in)Electrical system:Ignition system:
TCI
Charging system: AC magneto
U1CRE2E0.book Page 2 Monday, September 17, 2012 9:05 AM

SPECIFICATIONS
8-3
8
Battery:Model:GT14B-4
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:Halogen bulbBulb voltage, wattage × quantity:Low beam headlight:
12 V, 51.0 W × 1
High beam headlight: 12 V, 55.0 W × 1
Tail/brake light:
LED
Front turn signal light: 12 V, 21.0 W × 2
Rear turn signal light: 12 V, 21.0 W × 2
Auxiliary light:
12 V, 5.0 W × 2
License plate light: 12 V, 5.0 W × 1
Meter lighting: LED
Neutral indicator light:
LED
High beam indicator light: LED
Turn signal indicator light: LED
Fuel level warning light:
LED Engine trouble warning light:
LED
Immobilizer system indicator light: LED
Fuses:Main fuse:50.0 A
Headlight fuse: 25.0 A
Signaling system fuse:
10.0 A
Ignition fuse: 25.0 A
Parking lighting fuse: 10.0 A
Fuel injection system fuse:
15.0 A
Auxiliary DC connector fuse: 3.0 A
Backup fuse: 3.0 A
U1CRE2E0.book Page 3 Monday, September 17, 2012 9:05 AM

INDEX
AAir filter element.................................... 6-12
Auxiliary DC connector ......................... 3-22
Auxiliary light bulb, replacing ................ 6-30BBattery .................................................. 6-24
Brake and clutch fluid levels, checking ............................................. 6-17
Brake and clutch fluids, changing ......... 6-19
Brake and clutch levers, checking and lubricating ..................... 6-21
Brake and shift pedals,
checking and lubricating ..................... 6-21
Brake lever ........................................... 3-12
Brake lever free play, checking ............ 6-16
Brake light switches .............................. 6-16
Brake pedal .......................................... 3-12CCables, checking and lubricating .......... 6-20
Care ........................................................ 7-1
Catalytic converter ................................ 3-15
Clutch lever.................................. 3-11, 6-15DDimmer switch ...................................... 3-10
Drive belt slack ..................................... 6-19EEngine break-in ...................................... 5-3
Engine oil and oil filter cartridge ............. 6-9
Engine stop switch................................ 3-11
Engine trouble warning light ................... 3-4
EXUP system ....................................... 3-19FFront and rear brake pads, checking .... 6-17
Front fork, checking .............................. 6-23 Fuel ....................................................... 3-13
Fuel consumption, tips for reducing ........ 5-3
Fuel level warning light............................ 3-4
Fuel tank breather/overflow hose .......... 3-15
Fuel tank cap......................................... 3-13
Fuses, replacing .................................... 6-25
HHandlebar switches ............................... 3-10
Hazard switch........................................ 3-11
Headlight bulb, replacing....................... 6-26
Helmet holder ........................................ 3-16
High beam indicator light......................... 3-4
Horn switch ........................................... 3-11IIdentification numbers ............................. 9-1
Ignition circuit cut-off system ................. 3-20
Immobilizer system .................................3-1
Immobilizer system indicator light ........... 3-5
Indicator lights and warning lights ........... 3-4LLicense plate light .................................6-29MMain switch/steering lock ........................ 3-2
Maintenance and lubrication, periodic..... 6-4
Maintenance, emission control system ... 6-3
Matte color, caution .................................7-1
Model label .............................................. 9-1
Multi-function meter unit .......................... 3-5NNeutral indicator light .............................. 3-4PParking ....................................................5-4
Part locations .......................................... 2-1
RRear suspension, lubricating ................ 6-22
Rider seat ............................................. 3-16SSafety information ................................... 1-1
SELECT switch ..................................... 3-11
Shifting .................................................... 5-2
Shift pedal ............................................. 3-12
Shock absorber assembly, adjusting .... 3-17
Sidestand .............................................. 3-19
Sidestand, checking and lubricating ..... 6-22
Spark plugs, checking............................. 6-8
Specifications.......................................... 8-1
Starting the engine.................................. 5-1
Start switch ........................................... 3-11
Steering, checking ................................ 6-23
Storage ................................................... 7-3
Supporting the motorcycle .................... 6-30TTail/brake light ...................................... 6-29
Throttle grip and cable, checking and
lubricating ........................................... 6-20
Throttle grip free play, checking............ 6-13
Tires ...................................................... 6-13
Tool kit .................................................... 6-2
Transfer case oil ................................... 6-12
Troubleshooting .................................... 6-31
Troubleshooting chart ........................... 6-32
Turn signal indicator lights ...................... 3-4
Turn signal light bulb, replacing ............ 6-29
Turn signal switch ................................. 3-10VValve clearance .................................... 6-13
Vehicle identification number .................. 9-1
U1CRE2E0.book Page 1 Monday, September 17, 2012 9:05 AM