engine oil YAMAHA XV535 2000 User Guide

L
6-23
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EAU02986
Sidestand lubrication
Lubricate the sidestand pivoting point
and metal-to-metal contact surfaces.
Check that the sidestand moves up
and down smoothly.
EW000113
If the sidestand does not move
smoothly, consult a Yamaha dealer.Recommended lubricant:
Engine oil
EAU00790
Rear suspension lubrication
Lubricate the pivoting parts.
Recommended lubricant:
Molybdenum disulfide grease
EAU02939
Front fork inspection
Visual checkEW000115
Securely support the motorcycle so
there is no danger of it falling over.
Check for scratches or damage on the
inner tube and excessive oil leakage
from the front fork.

L
6-25
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
1. Battery
2. Pass through the battery case
3. Pass through the frame
4. Pass through the cable guide
5. Pass through the engine bracket
6. Battery breather hose
EAU00798
Battery
Check the level of the battery electro-
lyte and make sure that the terminals
are tight. Fill with distilled water if the
electrolyte level is low. If the motor-
cycle is equipped with optional electri-
cal accessories, the battery tends to
discharge more quickly, so be sure to
recharge it periodically.
EC000099
CAUTION:
When inspecting the battery, be
sure the breather hose is routed cor-
rectly. If the breather hose is posi-
tioned in such a way as to cause
battery electrolyte or gas to exit
onto the frame, structural and cos-
metic damage to the motorcycle can
occur.
EW000116
Battery electrolyte is poisonous and
dangerous, causing severe burns,
etc. It contains sulfuric acid. Avoid
contact with skin, eyes or clothing.
ANTIDOTE:
lEXTERNAL: Flush with water.
lINTERNAL: Drink large quanti-
ties of water or milk. Follow with
milk of magnesia, beaten egg,
or vegetable oil. Call a physi-
cian immediately.
lEYES: Flush with water for
15 minutes and get prompt
medical attention.
Batteries produce explosive gases.
Keep sparks, flame, cigarettes etc.,
away. Ventilate when charging or
using in an enclosed space. Always
shield your eyes when working near
batteries. KEEP OUT OF REACH OF
CHILDREN.

L
7-3
MOTORCYCLE CARE AND STORAGE
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-7.frame
1. Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
CAUTION:
Do not use warm water since it in-
creases the corrosive action of the
salt.
2. Be sure to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces
to prevent corrosion.After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the motorcycle dry completely
before storing it or covering it.
EWA00001
Make sure that there is no oil or wax
on the brakes and tires. If neces-
sary, clean the brake discs and lin-
ings with a regular brake disc
cleaner or acetone, and wash the
tires with warm water and mild soap.
Then, carefully test the motorcycle
for its braking performance and cor-
nering behavior.

L
7-5
MOTORCYCLE CARE AND STORAGE
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-7.frame
a. Remove the spark plug caps and
spark plugs.
b. Pour a teaspoonful of engine oil
into each spark plug bore.
c. Install the spark plug caps onto
the spark plugs and place the
spark plugs on the cylinder head
so that the electrodes are
grounded. (This will limit sparking
during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder walls with oil.)
e. Remove the spark plug caps from
the spark plugs, install the spark
plugs and then the spark plug
caps.
EWA00003
When turning the engine over, be
sure to ground the spark plug elec-
trodes to prevent damage or injury
from sparking.6. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.
7. Check and, if necessary, correct
the tire air pressure, then raise the
motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover up the muffler outlets with
plastic bags to prevent moisture
from entering.9. Remove the battery and fully
charge it. Store it in a cool, dry
place and recharge it once a
month. Do not store the battery in
an excessively cold or warm place
(less than 0ûC or more than 30ûC).
For more information, see ÒBattery
storageÓ in the chapter ÒPERIODIC
MAINTENANCE AND MINOR
REPAIRSÓ.
NOTE:
Make any necessary repairs before
storing the motorcycle.

L
8-1
SPECIFICATIONS
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-8.frame
Specifications
Model XV535
Dimensions
Overall length 2,225 mm
(except for CH, S, SF, N)
2,250 mm (for CH, S, SF, N)
Overall width 780 mm
Overall height 1,120 mm
Seat hight 720 mm
Wheelbase 1,520 mm
Ground clearance 160 mm
Minimum turning radius 2,900 mm
Basic weight (with oil and full
fuel tank)
195 kg (except for CH, A)
197 kg (for CH, A)
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement V type 2-cylinder
Displacement 535 cm
3
Bore´ Stroke 76.0 ´ 59.0 mm
Compression ratio 9:1
Starting system Electric starter
Lubrication system Wet sump
Engine oil
Ty p e
Recommended engine oil
classiÞcation API Service SE, SF, SG type or
higher
Quantity
Periodic oil change 2.6 L
With oil Þlter replacement 2.8 L
Total amount 3.2 L
-20û -10û 0û
10û20û 30û
40û50ûC
SAE 10W/30
SAE 15W/40
SAE 20W/40
SAE 20W/50
SAE 10W/40
CAUTION:
Be sure to use motor oils that do not contain anti-fric-
tion modifiers. Passenger car motor oils (often labeled
ÒEnergy ConservingÓ) contain anti-friction additives
which will cause clutch and/or starter clutch slippage,
resulting in reduced component life and poor engine
performance.
EAU01038

L
INDEX
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/XV535IX.-
A
Air filter .................................................6-10
B
Battery ..................................................6-25
Brake and clutch lever lubrication ........6-22
Brake and shift pedal lubrication ..........6-22
Brake fluid replacement ........................6-21
Brake light switch adjustment ...............6-19
C
Cable inspection and lubrication ..........6-21
Carburetor adjustment ..........................6-12
Care ........................................................7-1
Checking the front brake pads and
rear brake shoes ................................6-19
Clutch lever ............................................3-3
Clutch lever free play adjustment .........6-17
Controls/Instruments ..............................2-3
D
Dimmer switch ........................................3-2
E
Engine break-in ......................................5-5
Engine oil ................................................6-7
Engine stop switch .................................3-3
F
Final gear oil ...........................................6-9
Front brake lever ....................................3-4
Front brake lever free play
adjustment ........................................ 6-17
Front fork inspection ............................ 6-23
Fuel ........................................................ 3-5
Fuel reserve switch ................................ 3-3
Fuel tank cap ......................................... 3-5
Fuse replacement ................................ 6-27
G
Give safety the right of way ................... 1-1
H
Handlebar switches ............................... 3-2
Dimmer switch ................................. 3-2
Engine stop switch ........................... 3-3
Fuel reserve switch .......................... 3-3
Horn switch ...................................... 3-2
Lights switch .................................... 3-3
Pass switch ...................................... 3-2
Start switch ...................................... 3-3
Turn signal switch ............................ 3-2
Headlight bulb replacement ................. 6-27
Helmet holder ........................................ 3-8
High beam indicator light ....................... 3-1
Horn switch ............................................ 3-2
I
Identification number records ................ 9-1
Idle speed adjustment ......................... 6-13
Indicator lights ....................................... 3-1
High beam indicator light ................. 3-1
Neutral indicator light ....................... 3-1
Turn indicator light ............................ 3-1
Inspecting the brake fluid level ............ 6-20
K
Key identification number ...................... 9-1
L
Left view ................................................. 2-1
Lights switch .......................................... 3-3
M
Main switch ............................................ 3-1
Model label ............................................ 9-2
N
Neutral indicator light ............................. 3-1
P
Parking ................................................... 5-6
Pass switch ............................................ 3-2
Periodic maintenance and lubrication .... 6-2
Pre-operation check list ......................... 4-1
R
Rear brake pedal ................................... 3-4
Rear brake pedal height and free play
adjustment ......................................... 6-18
Rear shock absorber adjustment ........... 3-9
Rear suspension lubrication ................ 6-23
Recommended shift points
(for Switzerland only) .......................... 5-4
Right view .............................................. 2-2