drain bolt YAMAHA XV535 2000 Owners Manual

L
6-3
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
11*Tires¥ Check tread depth and for damage.
¥ Replace if necessary.
¥ Check air pressure.
¥ Correct if necessary.ÖÖ
12
*Wheel bearings¥ Check bearing for looseness or damage.
¥ Replace if necessary. ÖÖ
13
*Swingarm¥ Check swingarm pivoting point for play.
¥ Correct if necessary.
¥ Lubricate with molybdenum disulfide grease.ÖÖ
14
*Steering bearings¥ Check bearing play and steering for roughness.
¥ Correct accordingly.
¥ Lubricate with lithium soap base grease every 24,000 km
or 24 months (whichever comes first).ÖÖ
15
*Chassis fasteners¥ Make sure that all nuts, bolts and screws are properly tightened.
¥ Tighten if necessary.ÖÖ
16 Sidestand¥ Check operation.
¥ Lubricate and repair if necessary.ÖÖ
17
*Sidestand switch¥ Check operation.
¥ Replace if necessary.ÖÖÖ
18
*Front fork¥ Check operation and for oil leakage.
¥ Correct accordingly.ÖÖ
19
*Rear shock absorber
assemblies¥ Check operation and shock absorbers for oil leakage.
¥ Replace shock absorber assembly if necessary.ÖÖ
20
*Carburetors¥ Check engine idling speed, synchronization and starter operation.
¥ Adjust if necessary.ÖÖÖ
21 Engine oil¥ Check oil level and vehicle for oil leakage.
¥ Correct if necessary.
¥ Change. (Warm engine before draining.)ÖÖÖ NO. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
(1,000 km)EVERY
6,000 km
or
6 months
(whichever
comes first)12,000 km
or
12 months
(whichever
comes first)

R
6-8
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
1. Engine oil drain bolt
3. Remove the drain bolt and drain
the oil.
1. Oil filter cover
2. Bolt (´ 3)
4. Remove the oil filter bolts, oil filter
and O-ring.
5. Install the drain bolt and tighten it
to the specified torque.
6. Install the new oil filter, new O-ring
and the filter cover. Then tighten the
oil filter bolts to the specified torque. Tightening torque:
Drain bolt:
43 Nm (4.3 mákg)
Tightening torque:
Oil filter bolts:
10 Nm (1.0 mákg)
1. O-ring
2. Oil filter element
NOTE:
Make sure the O-ring is seated proper-
ly.
7. Fill the engine with oil. Install the
oil filler cap and tighten it.
Recommended oil:
See page 8-1.
Oil quantity:
Total amount:
3.2 L
Periodic oil change:
2.6 L
With oil filter replacement:
2.8 L

L
6-9
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-6.frame
EC000066
CAUTION:
lDo not put in any chemical addi-
tives. Engine oil also lubricates
the clutch and additives could
cause clutch slippage.
lBe sure no foreign material en-
ters the crankcase.
8. Start the engine and warm it up for
a few minutes. While warming up,
check for oil leakage. If oil leakage
is found, stop the engine immedi-
ately and check for the cause.
1. Final gear oil drain bolt
2. Final gear oil
3. Final gear oil filler bolt
4. Correct level
EAU02943
Final gear oil
EW000066
Do not let foreign material enter the
final gear case. Be sure oil does not
get on the tire or wheel.
Oil level inspection
1. Place the motorcycle on a level
place and hold it in an upright posi-
tion. The engine should be cool at
ambient temperature.2. Remove the oil filler bolt and
check the oil level. The oil level
should be at the brim of the filler
hole. Add the recommended oil if
necessary.
Oil replacement
1. Place an oil pan under the final
gear case.
2. Remove the oil filler bolt and drain
bolt to drain the oil.
3. Install and tighten the drain bolt to
the specified torque.
4. Fill the gear case to the brim of the
filler hole with the recommended
oil. Tightening torque:
Drain bolt:
23 Nm (2.3 mákg)

R
7-4
MOTORCYCLE CARE AND STORAGE
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9149_XV535-E6/English/E-7.frame
ECA00013
CAUTION:
lApply spray oil and wax spar-
ingly and wipe off any excess.
lNever apply oil or wax on rub-
ber and plastic parts, but treat
them with a suitable care prod-
uct.
lAvoid using abrasive polishing
compounds as they wear away
the paint.
NOTE:
Consult a Yamaha dealer for advice on
what products to use.
Storage
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA00014
CAUTION:
lStoring the motorcycle in a
poorly ventilated room or cov-
ering it with a tarp while it is still
wet will allow water and humidi-
ty to seep in and cause rust.
lTo prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
ÒCareÓ section of this chapter.
2. Drain the carburetor float cham-
bers by loosening the drain bolts;
this will prevent fuel deposits from
building up. Pour the drained fuel
into the fuel tank.
3. Only for motorcycles equipped
with a fuel cock which has an
ÒOFFÓ position: Turn the fuel cock
to ÒOFFÓ.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.