light YAMAHA XV535 2001 Owner's Manual

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
6 2. Disconnect the headlight coupler,
and then remove the headlight unit
and bulb cover.3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
EW000119
WARNING
@ Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. @4. Place a new bulb into position, and
then secure it with the bulb holder.
EC000105
CAUTION:@ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. @5. Install the bulb cover, and then
connect the coupler.
6. Install the headlight unit by install-
ing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight coupler
2. Headlight bulb cover
1. Headlight bulb holder
1. Do not touch this area.
E_3bt.book Page 32 Thursday, September 7, 2000 10:01 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-33
6
EAU00855
Replacing a turn signal light
bulb or the tail/brake light
bulb1. Remove the lens by removing the
screws.2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
CAUTION:@ Do not overtighten the screws, oth-
erwise the lens may break. @
EAU01579
Supporting the motorcycle Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcycle
by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1. Screw (´ 2)
1. Tail/brake light bulb (´ 2)
E_3bt.book Page 33 Thursday, September 7, 2000 10:01 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-37
6
EAU01406
To install the rear wheel
1. Apply a light coating of lithium-
soap-based grease to the splines
of the final gear case and wheel
hub.
2. Install the wheel by inserting the
wheel axle.
3. Install the brake rod onto the brake
camshaft lever, and then install
the brake pedal free play adjusting
nut onto the brake rod.
4. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut.
5. Install the rear wheel axle pinch
bolt.6. Lower the rear wheel so that it is
on the ground.
7. Tighten the axle nut, pinch bolt
and brake torque rod nut to the
specified torques.
8. Install the brake torque rod cotter
pin.
EW000124
WARNING
_ Always use a new cotter pin. _9. Adjust the brake pedal free play.
(See page 6-20 for brake pedal
free play adjustment procedures.)
EW000103
WARNING
_ After adjusting the brake pedal free
play, check the operation of the
brake light. _
EAU01008
TroubleshootingAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
Tightening torques:
Axle nut:
107 Nm (10.7 m·kg)
Rear wheel axle pinch bolt:
16 Nm (1.6 m·kg)
Brake torque rod nut:
20 Nm (2.0 m·kg)
E_3bt.book Page 37 Thursday, September 7, 2000 10:01 AM

MOTORCYCLE CARE AND STORAGE
7-2
7
l
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
l
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
l
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
@After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:@ Salt sprayed on roads in the winter may
remain well into spring. @1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:@ Do not use warm water since it in-
creases the corrosive action of the
salt. @2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent
corrosion.
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM

SPECIFICATIONS
8-3
8
Maximum load* 220 kg (except for A)
218 kg (for A)
Tire air pressure
(measured on cold tires)
Up to 90 kg*
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 225 kPa (2.25 kg/cm2, 2.25 bar)
90 kg–maximum*
Front 200 kPa (2.00 kg/cm2, 2.00 bar)
Rear 250 kPa (2.50 kg/cm2, 2.50 bar)
* Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type Spoke wheel
Size 19 ´ MT 1.85
Rear
Type Spoke wheel
Size 15 M/C ´ MT 3.00
Brakes
Front
Type Single disc brake
Operation Right hand
Fluid DOT 4 or DOT 3Rear
Type Drum brake
Operation Right foot
Suspension
Front Telescopic fork
Rear Swingarm
Springs/shock absorbers
Front Coil spring / oil damper
Rear Coil spring / oil damper
Wheel travel
Front 150 mm
Rear 85 mm
Electrical system
Ignition system T.C.I. (digital)
Charging system
Type A.C. magneto
Standard output 14 V, 24 A @ 5,000 r/min
Battery
Model GM12AZ-3A-2
Voltage, capacity 12 V, 12 Ah
Headlight typeQuartz bulb (halogen)
E_3bt.book Page 3 Thursday, September 7, 2000 10:01 AM

SPECIFICATIONS
8-4
8
Bulb voltage, wattage ´ quantity
Headlight 12 V, 60/55 W ´ 1
Auxiliary light 12 V, 4 W ´ 1 (except for GB)
12V, 3.4 W ´ 1 (for GB)
Tail/brake light 12 V, 5/21 W ´ 2
Front turn signal light 12 V, 21 W ´ 2
Rear turn signal light 12 V, 21 W ´ 2
Meter lighting 14 V, 3 W ´ 1
Neutral indicator light 14 V, 3 W ´ 1
High beam indicator light 12 V, 1.7 W ´ 1
Turn signal indicator light 14 V, 3 W ´ 1
Fuses
Main fuse 30 A
Ignition fuse 15 A
Signaling system fuse 15 A
Headlight fuse 15 A
E_3bt.book Page 4 Thursday, September 7, 2000 10:01 AM

10-INDEXAAir filter element, cleaning ...................... 6-11BBattery ................................................... 6-29
Brake and clutch levers, checking and
lubricating ............................................ 6-25
Brake and shift pedals, checking and
lubricating ............................................ 6-25
Brake fluid, changing ............................. 6-23
Brake fluid level, checking...................... 6-22
Brake lever...............................................3-4
Brake lever free play, adjusting .............. 6-19
Brake light switch, adjusting ................... 6-21
Brake pads and shoes, checking ........... 6-21
Brake pedal..............................................3-4
Brake pedal position and free play,
adjusting .............................................. 6-19CCables, checking and lubricating............ 6-23
Carburetors, adjusting............................ 6-13
Care.........................................................7-1
Clutch lever ..............................................3-3
Clutch lever free play, adjusting ............. 6-18
Conversion table ......................................8-5DDimmer switch .........................................3-2
EEngine break-in ....................................... 5-4
Engine oil and oil filter element ................ 6-7
Engine stop switch................................... 3-3FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-27
Fuel ......................................................... 3-5
Fuel consumption, tips for reducing ......... 5-4
Fuel reserve switch.................................. 3-3
Fuel tank cap ........................................... 3-5
Fuses, replacing .................................... 6-31HHandlebar switches ................................. 3-2
Headlight bulb, replacing ....................... 6-31
Helmet holder .......................................... 3-9
High beam indicator light ......................... 3-1
Horn switch ............................................. 3-2IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-13
Ignition circuit cut-off system.................. 3-10
Indicator lights ......................................... 3-1KKey identification number ........................ 9-1
LLight switch ..............................................3-3MMain switch ..............................................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-1PParking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-2
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .......................................................3-7
Passenger seat...................................3-7
Rider seat ...........................................3-8
Shifting .....................................................5-3
Shift pedal ................................................3-4
Shift points (for Switzerland only) .............5-3
Shock absorber assemblies, adjusting .....3-9
Sidestand ...............................................3-10
Sidestand, checking and lubricating .......6-25
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM

INDEX
Spark plugs, checking ............................. 6-5
Specifications .......................................... 8-1
Speedometer unit .................................... 3-2
Starter (choke) lever ................................ 3-6
Starting a cold engine .............................. 5-1
Starting a warm engine ............................ 5-2
Start switch .............................................. 3-3
Steering, checking ................................. 6-27
Steering lock............................................ 3-7
Storage.................................................... 7-4
Supporting the motorcycle ..................... 6-33
Suspension (rear), lubricating ................ 6-26TThrottle cable free play, adjusting .......... 6-14
Throttle grip and cable, checking and
lubricating............................................ 6-24
Tires ...................................................... 6-15
Tool kit..................................................... 6-1
Troubleshooting..................................... 6-37
Troubleshooting chart ............................ 6-38
Turn signal indicator light ......................... 3-1
Turn signal or tail/brake light bulb,
replacing ............................................. 6-33
Turn signal switch .................................... 3-2VValve clearance, adjusting ..................... 6-14
Vehicle identification number ................... 9-1
WWheel bearings, checking ..................... 6-28
Wheel (front) ......................................... 6-34
Installing .......................................... 6-35
Removing ........................................ 6-34
Wheel (rear) .......................................... 6-35
Installing .......................................... 6-37
Removing ........................................ 6-35
Wheels .................................................. 6-17
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM