high beam YAMAHA XV535 2001 Owners Manual

3-1
3
EAU00027
3-INSTRUMENT AND CONTROL FUNCTIONS
EAU00028
Main switch The main switch controls the ignition
and lighting systems. The various main
switch positions are described below.
EAU00036
ON
All electrical systems are supplied with
power, and the engine can be started.
The key cannot be removed.
EAU00038
OFF
All electrical systems are off. The key
can be removed.
EAU00055
P (Parking)
The taillight and auxiliary light are on,
but all other electrical systems are off.
The key can be removed.
The key must be pushed in, and then
released before it can be turned to “P”.
ECA00043
CAUTION:@ Do not use the parking position for
an extended length of time, other-
wise the battery may discharge. @
EAU00056
Indicator lights
EAU00063
High beam indicator light “ ”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU00061
Neutral indicator light “ ”
This indicator light comes on when the
transmission is in the neutral position.
EAU00057
Turn signal indicator light “ ”
This indicator light flashes when the turn
signal switch is pushed to the left or right.
1. Push.
2. Release.
3. Turn.
1. High beam indicator light “ ”
2. Neutral indicator light “ ”
3. Turn signal indicator light “ ”
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-2
3
EAU00095
Speedometer unit The speedometer unit is equipped with
a speedometer, an odometer and a
tripmeter. The speedometer shows
riding speed. The odometer shows the
total distance traveled. The tripmeter
shows the distance traveled since it
was last set to zero with the reset knob.
The tripmeter can be used to estimate
the distance that can be traveled with a
full tank of fuel. This information will en-
able you to plan future fuel stops.
EAU00118
Handlebar switches
EAU00119
Pass switch “ ”
Press this switch to flash the headlight.
EAU00121
Dimmer switch
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
EAU00124
Turn signal switch
To signal a right-hand turn, push this
switch to the right. To signal a left-hand
turn, push this switch to the left. When
released, the switch returns to the cen-
ter position.
Since this model is equipped with a self-
canceling system, the turn signal lights
will self-cancel after the motorcycle has
traveled both about 150 m and for ap-
proximately 15 seconds. However, the
turn signal lights can also be canceled
manually by pushing the switch in after
it has returned to the center position.NOTE:@ The self-canceling system only oper-
ates when the motorcycle is moving, so
that the turn signal lights will not self-
cancel while you are stopped at an
intersection.@
EAU00129
Horn switch “ ”
Press this switch to sound the horn.
1. Tripmeter reset knob
2. Odometer
3. Tripmeter
1. Pass switch “ ”
2. Dimmer switch
3. Turn signal switch
4. Horn switch “ ”
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM

SPECIFICATIONS
8-4
8
Bulb voltage, wattage ´ quantity
Headlight 12 V, 60/55 W ´ 1
Auxiliary light 12 V, 4 W ´ 1 (except for GB)
12V, 3.4 W ´ 1 (for GB)
Tail/brake light 12 V, 5/21 W ´ 2
Front turn signal light 12 V, 21 W ´ 2
Rear turn signal light 12 V, 21 W ´ 2
Meter lighting 14 V, 3 W ´ 1
Neutral indicator light 14 V, 3 W ´ 1
High beam indicator light 12 V, 1.7 W ´ 1
Turn signal indicator light 14 V, 3 W ´ 1
Fuses
Main fuse 30 A
Ignition fuse 15 A
Signaling system fuse 15 A
Headlight fuse 15 A
E_3bt.book Page 4 Thursday, September 7, 2000 10:01 AM

10-INDEXAAir filter element, cleaning ...................... 6-11BBattery ................................................... 6-29
Brake and clutch levers, checking and
lubricating ............................................ 6-25
Brake and shift pedals, checking and
lubricating ............................................ 6-25
Brake fluid, changing ............................. 6-23
Brake fluid level, checking...................... 6-22
Brake lever...............................................3-4
Brake lever free play, adjusting .............. 6-19
Brake light switch, adjusting ................... 6-21
Brake pads and shoes, checking ........... 6-21
Brake pedal..............................................3-4
Brake pedal position and free play,
adjusting .............................................. 6-19CCables, checking and lubricating............ 6-23
Carburetors, adjusting............................ 6-13
Care.........................................................7-1
Clutch lever ..............................................3-3
Clutch lever free play, adjusting ............. 6-18
Conversion table ......................................8-5DDimmer switch .........................................3-2
EEngine break-in ....................................... 5-4
Engine oil and oil filter element ................ 6-7
Engine stop switch................................... 3-3FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-27
Fuel ......................................................... 3-5
Fuel consumption, tips for reducing ......... 5-4
Fuel reserve switch.................................. 3-3
Fuel tank cap ........................................... 3-5
Fuses, replacing .................................... 6-31HHandlebar switches ................................. 3-2
Headlight bulb, replacing ....................... 6-31
Helmet holder .......................................... 3-9
High beam indicator light ......................... 3-1
Horn switch ............................................. 3-2IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-13
Ignition circuit cut-off system.................. 3-10
Indicator lights ......................................... 3-1KKey identification number ........................ 9-1
LLight switch ..............................................3-3MMain switch ..............................................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-1PParking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-2
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .......................................................3-7
Passenger seat...................................3-7
Rider seat ...........................................3-8
Shifting .....................................................5-3
Shift pedal ................................................3-4
Shift points (for Switzerland only) .............5-3
Shock absorber assemblies, adjusting .....3-9
Sidestand ...............................................3-10
Sidestand, checking and lubricating .......6-25
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM