maintenance YAMAHA XV950 2014 Owner's Guide

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
6is turne
d to “OFF”, then connect
the positive lea d before con-
nectin g the ne gative lea d.
[ECA16841]
4. After installation, make sure that
the battery leads are properly con-
nected to the battery terminals.NOTICE
ECA16531
Always keep the b attery charged .
Storin g a d ischar ged battery can
cause permanent battery dama ge.
EAU57791
Replacin g the fusesThe main fuse, the fuel injection sys-
tem fuse (for non-ABS models) or the
ABS motor fuse (for ABS models), and
the fuse boxes, which contain the fus-
es for the individual circuits, are locat-
ed under the owner’s tool box behind
panel A. (See page 6-8.)TIPTo access the fuel injection system
fuse (for non-ABS models) or the ABS
motor fuse (for ABS models), remove
the starter relay cover by pulling it up-
ward.
For non-ABS mo dels1. Fuse box
2. Main fuse
3. Starter relay cover
4. Fuel injection system fuse
5. Fuel injection system spare fuse
3
2
1
4
5
U2DEE0E0.book Page 27 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-28
6
For non-ABS mo
dels For ABS mo dels For ABS mo dels
If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a hi gher ampera ge
ratin g than recommen ded to
1. Ignition fuse
2. Signaling system fuse
3. Parking lighting fuse
4. Backup fuse (for clock and immobilizer sys-
tem)
5. Headlight fuse
6. Spare fuse
2 1
3
4
5
6
1. Fuse box
2. Main fuse
3. Starter relay cover
4. ABS motor fuse
5. ABS motor spare fuse
3
2
1
4
5
1. Ignition fuse
2. ABS control unit fuse
3. Signaling system fuse
4. Parking lighting fuse
5. Backup fuse (for clock and immobilizer sys-tem)
6. Headlight fuse
7. Spare fuse
8. Fuel injection system fuse
9. ABS solenoid fuse
2 1
4
5
6
7
789
3
U2DEE0E0.book Page 28 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6avoi
d causin g extensive d am-
a g e to the electrical system an d
possi bly a fire.
[EWA15132]
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU48514
Replacin g the hea dlig ht bul bThis model is equipped with a halogen
bulb headlight. If the headlight bulb
burns out, replace it as follows.NOTICE
ECA10651
Take care not to damag e the follow-
in g parts:
 Hea dlig ht bul b
Do not touch the glass part of
the hea dlig ht bul b to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the b ulb, an d the bul b life will
b e ad versely affected . Thor-
ou ghly clean off any dirt an d fin-
g erprints on the head lig ht bul b
usin g a cloth moistene d with al-
cohol or thinner.
 Hea dlig ht lens
Do not affix any type of tinted
film or stickers to the hea dlig ht
lens.
Do not use a hea dlig ht bul b of a
wattag e higher than specifie d.
1. Remove the headlight unit by re-
moving the screws.
2. Disconnect the headlight coupler, and then remove the headlight
bulb cover.
Specifie d fuses:
Main fuse: 40.0 A
Headlight fuse:
20.0 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Parking lighting fuse:
15.0 A
Fuel injection system fuse: 10.0 A
ABS motor fuse: For ABS models 30.0 A
ABS solenoid fuse:
For ABS models 15.0 A
ABS control unit fuse: For ABS models 7.5 A
Backup fuse: 7.5 A
1. Do not touch the glass part of the bulb.
1. Screw
1
U2DEE0E0.book Page 29 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
6
3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into position, and then secure it with
the bulb holder. 5. Install the bulb cover, and then
connect the coupler.
TIPWhen installing the headlight bulb cov-
er, make sure the “TOP” mark faces
upwards.6. Install the headlight unit by install-ing the screws.
7. Have a Yamaha dealer adjust the headlight beam if necessary.
EAU24182
Tail/b rake li ghtThis model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
1. Headlight coupler
2. Headlight bulb cover
1. Headlight bulb holder
2
11
1. “TOP” mark
1
U2DEE0E0.book Page 30 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
6
EAU24214
Replacing a turn si gnal li ght
b ul b1. Remove the turn signal light lens
by removing the screws.
2. Remove the burnt-out bulb by pushing it in and turning it coun-
terclockwise. 3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screws. NOTICE: Do not over-
ti g hten the screws, otherwise
the lens may break.
[ECA10682] EAU24331
License plate li
ghtIf the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.
1. Screw
2. Turn signal light lens
2
1
1. Turn signal light bulb
1
U2DEE0E0.book Page 31 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
6
EAU45226
Replacing the auxiliary li ght
b ul b If the auxiliary light bulb burns out, re-
place it as follows.
1. Remove the headlight unit. (See page 6-29.)
2. Remove the auxiliary light bulb socket (together with the bulb) by
pulling it out.
3. Remove the burnt-out bulb by pulling it out. 4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the headlight unit.
EAU24351
Supportin g the motorcycleSince this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motorcy-
cle is in a stable and level position be-
fore starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy- cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing a
jack under the frame in front of the
rear wheel.
2. Raise the front wheel off the ground by using a motorcycle
stand.
To service the rear wheel
Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing
1. Auxiliary light bulb socket
1
1. Auxiliary light bulb
1
U2DEE0E0.book Page 32 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
6a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.
EAU25852
Trou
bleshootin gAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
WARNING
EWA15142
When checkin g the fuel system, do
not smoke, an d make sure there are
no open flames or sparks in the ar-
ea, inclu din g pilot lig hts from water heaters or furnaces. Gasoline or
g
asoline vapors can i gnite or ex-
plod e, causin g severe injury or prop-
erty damag e.
U2DEE0E0.book Page 33 Friday, June 14, 2013 1:29 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
6
EAU42604
Troubleshootin g chart
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.
There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
Remove the spark plugs
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start.
Have a Yamaha dealer check the vehicle.Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the compression.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The engine does not start.
Check the ignition.
The battery is good.Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
DryWet
Operate the electric starter.
U2DEE0E0.book Page 34 Friday, June 14, 2013 1:29 PM

INDEXAABS (for ABS models) ........................... 3-11
ABS warning light (for ABS models) ....... 3-4
Air filter element, replacing ................... 6-13
Auxiliary light bulb, replacing ................ 6-32BBattery .................................................. 6-26
Brake and clutch levers, checking and lubricating ........................................... 6-23
Brake and shift pedals, checking and lubricating ........................................... 6-22
Brake fluid, changing ............................ 6-20
Brake fluid level, checking .................... 6-19
Brake lever ............................................ 3-10
Brake lever free play, checking............. 6-17
Brake light switches.............................. 6-18
Brake pedal........................................... 3-11CCables, checking and lubricating ......... 6-21
Care ........................................................ 7-1
Catalytic converter ................................ 3-14
Clutch lever ........................................... 3-10
Clutch lever free play, adjusting ........... 6-16DDimmer switch ........................................ 3-8
Drive belt slack ..................................... 6-21EEngine break-in....................................... 5-3
Engine oil and oil filter cartridge ........... 6-10
Engine stop switch ................................. 3-9
Engine trouble warning light ................... 3-4FFront and rear brake pads, checking.... 6-18
Front fork, checking .............................. 6-24 Fuel ....................................................... 3-13
Fuel consumption, tips for reducing ...... 5-3
Fuel level warning light ........................... 3-4
Fuel tank breather/overflow hose ......... 3-14
Fuel tank cap ........................................ 3-12
Fuses, replacing ................................... 6-27
HHandlebar switches ................................ 3-8
Hazard switch......................................... 3-9
Headlight bulb, replacing ..................... 6-29
High beam indicator light ....................... 3-3
Horn switch ............................................ 3-9IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-18
Immobilizer system ................................ 3-1
Immobilizer system indicator light .......... 3-5
Indicator lights and warning lights ......... 3-3LLicense plate light ................................ 6-31MMain switch ............................................ 3-2
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system.................................................. 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-5NNeutral indicator light ............................. 3-3OOil level warning light ............................. 3-3PPanel, removing and installing ............... 6-8 Parking ....................................................5-4
Part locations ..........................................2-1
Pass switch .............................................3-8
RRESET switch .........................................3-9
Rider seat ..............................................3-16SSafety information ...................................1-1
SELECT switch .......................................3-9
Shifting ....................................................5-2
Shift pedal .............................................3-10
Shock absorber assemblies,
adjusting .............................................3-17
Sidestand ..............................................3-17
Sidestand, checking and lubricating.....6-23
Spark plugs, checking ............................6-8
Specifications .........................................8-1
Starting the engine ..................................5-1
Start switch .............................................3-9
Steering, checking ................................6-25
Steering lock .........................................3-15
Storage ...................................................7-3
Supporting the motorcycle ...................6-32
Swingarm pivots, lubricating ................6-24TTail/brake light ......................................6-30
Throttle grip and cable, checking and lubricating ...........................................6-22
Throttle grip free play, checking ...........6-13
Tires ......................................................6-14
Tool kit ....................................................6-2
Troubleshooting ....................................6-33
Troubleshooting chart ...........................6-34
Turn signal indicator light........................3-3
U2DEE0E0.book Page 1 Friday, June 14, 2013 1:29 PM