brake YAMAHA XVS1100A 2001 Owner's Manual

PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
64. Grease the metal-to-metal contact
surface of the throttle grip, and
then install the grip by installing
the screws.
EAU03370
Checking and lubricating the
brake and shift pedals The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.
EAU03164
Checking and lubricating the
brake and clutch levers The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary. Recommended lubricant:
Throttle cable:
Engine oil
Throttle grip housing and grip:
Lithium-soap-based grease
(all-purpose grease)
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
E_5pb.book Page 23 Thursday, October 5, 2000 10:10 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-24
6
EAU03165
Checking and lubricating the
sidestand The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.
EW000113
WARNING
@ If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. @
EAU02939
Checking the front fork The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
EW000115
WARNING
@ Securely support the motorcycle so
that there is no danger of it falling
over. @Check the inner tubes for scratches,
damage and excessive oil leakage.To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
EC000098
CAUTION:@ If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it. @
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
E_5pb.book Page 24 Thursday, October 5, 2000 10:10 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
EC000105
CAUTION:@ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. @5. Install the bulb cover, and then
connect the coupler.
6. Install the headlight unit by install-
ing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU00855
Replacing a turn signal light
bulb or the tail/brake light
bulb 1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.1. Screw (´ 2)
1. Screw (´ 2)XVS1100
E_5pb.book Page 31 Thursday, October 5, 2000 10:10 AM

MOTORCYCLE CARE AND STORAGE
7-2
7 thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
l
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments, switch-
es and lights), breather hoses
and vents.
l
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-shield is scratched, use a quali-
ty plastic polishing compound
after washing.
_
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:_ Salt sprayed on roads in the winter may
remain well into spring. _
E_5pb.book Page 2 Thursday, October 5, 2000 10:10 AM

MOTORCYCLE CARE AND STORAGE
7-3
71. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:_ Do not use warm water since it in-
creases the corrosive action of the
salt. _2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the motorcycle dry completely
before storing or covering it.
EWA00031
WARNING
_ l
Make sure that there is no oil or
wax on the brakes or tires.
l
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
_
E_5pb.book Page 3 Thursday, October 5, 2000 10:10 AM

SPECIFICATIONS
8-4
8
Wheels
XVS1100
Fron t
Type Spoke wheel
Size 18 ´ 2.15
Rear
Type Spoke wheel
Size 15 M/C ´ MT 4.50
XVS1100A
Fron t
Type Spoke wheel
Size 16 ´ 3.00
Rear
Type Spoke wheel
Size 15 M/C ´ MT 4.50
Brakes
Front
Type Dual disc brake
Operation Right hand
Fluid DOT 4
Rear
Type Single disc brake
Operation Right foot
Fluid DOT 4Suspension
Front Telescopic fork
Rear Swingarm (link suspension)
Spring/shock absorber
Front Coil spring / oil damper
Rear Coil spring / gas-oil damper,
spring preload adjustable
Wheel travel
Front 140 mm
Rear 113 mm
Electrical system
Ignition system Transistorized coil ignition
(digital)
Charging system
Type A.C. magneto
Standard output
XVS1100 14 V, 305 W@ 5,000 r/min
XVS1100A 14 V, 350 W@ 5,000 r/min
Battery
Model GT14B-4
Voltage, capacity 12 V, 12 Ah
Headlight typeQuartz bulb (halogen)
E_5pb.book Page 4 Thursday, October 5, 2000 10:10 AM

SPECIFICATIONS
8-5
8
Bulb voltage, wattage ´ quantity
Headlight 12 V, 60/55 W ´ 1
Auxiliary light 12 V, 4 W ´ 1
Tail/brake light 12 V, 5/21 W ´ 1
Turn signal light 12 V, 21 W ´ 4
Meter lighting 14 V, 1.4 W ´ 2
Oil level warning light 12 V, 1.7 W ´ 1
Neutral indicator light 12 V, 1.7 W ´ 1
Turn signal indicator light 12 V, 1.7 W ´ 1
Engine trouble warning light 12 V, 1.7 W ´ 1
High beam indicator light 12 V, 1.7 W ´ 1
Fuses
Main fuse 30 A
Signaling system fuse 10 A
Odometer fuse 5 A
Ignition fuse 10 A
Headlight fuse 15 A
Carburetor heater fuse 15 A
E_5pb.book Page 5 Thursday, October 5, 2000 10:10 AM

10-INDEXAAir filter element, cleaning ...................... 6-11
Anti-theft alarm (optional) .........................3-4BBattery ................................................... 6-26
Brake and clutch levers, checking
and lubricating ..................................... 6-23
Brake and shift pedals, checking
and lubricating ..................................... 6-23
Brake fluid, changing ............................. 6-22
Brake fluid level, checking...................... 6-21
Brake lever...............................................3-6
Brake lever free play, adjusting .............. 6-17
Brake light switch, adjusting ................... 6-19
Brake pads, checking............................. 6-20
Brake pedal..............................................3-7
Brake pedal position, adjusting .............. 6-19CCables, checking and lubricating............ 6-22
Carburetors, adjusting............................ 6-12
Care.........................................................7-1
Clutch lever ..............................................3-5
Clutch lever free play, adjusting ............. 6-17
Conversion table ......................................8-6DDimmer switch .........................................3-4EEngine break-in........................................5-5
Engine oil and oil filter element.................6-7
Engine, starting a warm ...........................5-3
Engine stop switch ...................................3-5
Engine trouble warning light .................... 3-3FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-24
Fuel ......................................................... 3-8
Fuel cock ................................................. 3-9
Fuel consumption, tips for reducing ......... 5-4
Fuel tank cap ........................................... 3-7
Fuses, replacing .................................... 6-28HHandlebar switches ................................. 3-4
Headlight bulb, replacing ....................... 6-30
Helmet holder ........................................ 3-13
High beam indicator light ......................... 3-3
Horn switch ............................................. 3-4IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-12
Ignition circuit cut-off system.................. 3-19
Indicator and warning lights ..................... 3-2KKey identification number ........................ 9-1LLight switch.............................................. 3-5
Luggage strap holders ........................... 3-18MMain switch/steering lock ......................... 3-1
Model label .............................................. 9-2
NNeutral indicator light ...............................3-2OOil level warning light ...............................3-2PPart locations............................................. 2-1
Panel, removing and installing..................6-5
Parking.....................................................5-5
Pass switch ..............................................3-4
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1SSafety information ..................................... 1-1
Seats (XVS1100) ...................................3-11
Passenger seat.................................3-11
Rider seat .........................................3-11
Seats (XVS1100A) .................................3-12
Passenger seat.................................3-12
Rider seat .........................................3-13
Shifting .....................................................5-3
Shift pedal (XVS1100)..............................3-6
Shift pedal (XVS1100A) ...........................3-6
Shift points (for Switzerland only) .............5-4
Shock absorber assembly, adjusting ......3-15
Sidestand ...............................................3-18
Sidestand, checking and lubricating .......6-24
Spark plugs, checking ..............................6-6
Specifications ...........................................8-1
Speedometer unit.....................................3-3
Starter (choke) lever...............................3-10
E_5pb.book Page 1 Thursday, October 5, 2000 10:10 AM

INDEX
Starting the engine .................................. 5-1
Start switch .............................................. 3-5
Steering, checking ................................. 6-25
Storage.................................................... 7-4
Storage compartment ............................ 3-14TThrottle cable free play, adjusting .......... 6-13
Throttle grip and cable, checking
and lubricating ..................................... 6-22
Tires ...................................................... 6-13
Tool kit..................................................... 6-1
Troubleshooting..................................... 6-32
Troubleshooting chart ............................ 6-33
Turn signal indicator light ......................... 3-2
Turn signal or tail/brake light bulb,
replacing ............................................. 6-31
Turn signal switch .................................... 3-4VValve clearance, adjusting ..................... 6-13
Vehicle identification number ................... 9-1WWheel bearings, checking...................... 6-25
Wheels .................................................. 6-16
E_5pb.book Page 2 Thursday, October 5, 2000 10:10 AM