ABS YAMAHA XVS125 2000 Owners Manual

EAU00009
TABLE OF CONTENTS
GIVE SAFETY THE RIGHT OF WAY ..................1-1
DESCRIPTION ....................................................2-1
Left view .............................................................2-1
Right view ..........................................................2-2
Controls and Instruments ...................................2-3
INSTRUMENT AND CONTROL
FUNCTIONS ........................................................3-1
Main switch/steering lock ...................................3-1
Indicator lights ....................................................3-2
Speedometer unit ..............................................3-2
Anti-theft alarm (optional)...................................3-3
Handlebar switches............................................3-3
Clutch lever ........................................................3-5
Shift pedal ..........................................................3-5
Brake lever .........................................................3-5
Brake pedal ........................................................3-6
Fuel tank cap .....................................................3-6
Fuel ....................................................................3-7
Fuel cock............................................................3-7
Starter (choke) lever ..........................................3-8
Helmet holder.....................................................3-9
Adjusting the shock absorber assemblies..........3-9
Sidestand .........................................................3-10
Ignition circuit cut-off system............................3-10PRE-OPERATION CHECKS ...............................4-1
Pre-operation check list .....................................4-1
OPERATION AND IMPORTANT RIDING
POINTS................................................................5-1
Starting the engine .............................................5-1
Starting a warm engine ......................................5-3
Shifting ...............................................................5-3
Recommended shift points
(for Switzerland only) .......................................5-4
Tips for reducing fuel consumption ....................5-4
Engine break-in ..................................................5-4
Parking ...............................................................5-5
PERIODIC MAINTENANCE AND MINOR
REPAIR................................................................6-1
Owner’s tool kit ..................................................6-1
Periodic maintenance and lubrication chart .......6-2
Removing and installing panels .........................6-5
Checking the spark plugs...................................6-7
Engine oil and oil filter element ..........................6-9
Cleaning the air filter element ..........................6-12
Adjusting the carburetor ...................................6-14
Adjusting the engine idling speed ....................6-14
Adjusting the throttle cable free play ................6-15
Adjusting the valve clearance ..........................6-161
2
3
4
5
6
5JX-9-E0 4/9/0 4:11 AM Page 5

EAU00026
DESCRIPTION
2
2-1
1. Headlight (page 6-34)
2. Fuel cock (page 3-7)
3. Fuses (page 6-33)
4. Helmet holder (page 3-9)
5. Rear shock absorber spring preload
adjusting ring (page 3-9)6. Shift pedal (page 3-5)
1234
5
6
Left view
5JX-9-E0 4/9/0 4:11 AM Page 8

DESCRIPTION
2
2-2
7. Tool kit (page 6-1)
8. Battery (page 6-31)
9. Air filter (page 6-12)
10. Main switch/steering lock (page 3-1)
11. Brake pedal (page 3-6, 6-21)12. Oil filter element (page 6-9)
13. Rear shock absorber spring preload
adjusting ring (page 3-9)
78 910
11
12 13
Right view
5JX-9-E0 4/9/0 4:11 AM Page 9

INSTRUMENT AND CONTROL FUNCTIONS
3
3-9
EAU00260
Helmet holder
To open the helmet holder, insert the
key into the lock, and then turn the
key as shown.
To lock the helmet holder, place it in
the original position, and then remove
the key.
EW000030
w
Never ride with a helmet attached
to the helmet holder, since the hel-
met may hit objects, causing loss
of control and possibly an acci-
dent.
1. Helmet holder
2. Open
1
2
EW000040
w
Always adjust both shock
absorber assemblies equally, oth-
erwise poor handling and loss of
stability may result.
Adjust the spring preload as follows.
To increase the spring preload and
thereby harden the suspension, turn
the adjusting ring on each shock
absorber assembly in direction a. To
decrease the spring preload and
thereby soften the suspension, turn
the adjusting ring on each shock
absorber assembly in direction b.
NOTE:
Align the appropriate notch in the
adjusting ring with the position indica-
tor on the shock absorber.
EAU00300
Adjusting the shock
absorber assemblies
Each shock absorber assembly is
equipped with a spring preload
adjusting ring.
EC000015
cC
Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.
1. Rear shock absorber spring preload
adjusting ring
2. Position indicator
1
2
3
4
5
b
a
2
1
Minimum
StandardMaximum(soft) (hard)
Setting 1 2 3 4 5
5JX-9-E0 4/9/0 4:11 AM Page 19

PERIODIC MAINTENANCE AND MINOR REPAIR
6
6-3
13 Drive chain¥ Check chain slack.
¥ Adjust if necessary. Make sure that the rear wheel is properly
aligned.
¥ Clean and lubricate.Every 1,000 km and after washing the
motorcycle or riding in the rain
14
*Steering bearings¥ Check bearing play and steering for roughness.
¥ Correct accordingly.
¥ Lubricate with lithium-soap-based grease every 24.000 km or 24
months (whichever comes first)ÖÖ
15
*Chassis fasteners¥ Make sure that all nuts, bolts and screws are properly tightened.
¥ Tighten if necessary.ÖÖ
16 Sidestand¥ Check operation.
¥ Lubricate and repair if necessary.ÖÖ
17
*Sidestand switch¥ Check operation.
¥ Replace if necessary.ÖÖ Ö
18
*Front fork¥ Check operation and for oil leakage.
¥ Correct accordingly.Ö
19
*Rear shock absorber
assemblies¥ Check operation and shock absorbers for oil leakage.
¥ Replace shock absorber assembly if necessary.Ö
20
*Carburetor¥ Check engine idling speed and starter operation.
¥ Adjust if necessary.ÖÖ Ö
21 Engine oil¥ Check oil level and vehicle for oil leakage.
¥ Correct accordingly.
¥ Change. (Warm engine before draining.)ÖÖ Ö
22 Engine oil filter element¥ Replace.ÖÖ
23
*Front and rear brake
switches¥ Check operation.
¥ Correct accordingly.ÖÖ Ö
24
*Moving parts and cables¥ Lubricate if necessary.ÖÖ No. ITEM CHECKS AND MAINTENANCE JOBSInitial
1,000 kmEvery
6,000 kmEvery
12,000 kmAnnual
check
5JX-9-E0 4/9/0 4:11 AM Page 31

MOTORCYCLE CARE AND STORAGE
7
7-3
After cleaning
1. Dry the motorcycle with a
chamois or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated,
surfaces.
5. Use spray oil as a universal
cleaner to remove any remaining
dirt.
6. Touch up minor paint damage
caused by stones, etc.7. Wax all painted surfaces.
8. Let the motorcycle dry complete-
ly before storing or covering it.
EWA00001
w
8Make sure that there is no oil
or wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
8Before operating the motorcy-
cle test its braking perfor-
mance and cornering behav-
ior.
ECA00013
cC
8Apply spray oil and wax spar-
ingly and make sure to wipe
off any excess.
8Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
8Avoid using abrasive polish-
ing compounds as they will
wear away the paint.
NOTE:
Consult a Yamaha dealer for advice
on what products to use.
5JX-9-E0 4/9/0 4:11 AM Page 73

8
SPECIFICATIONS
8-3
Maximum load* 183 kg
Air pressure (cold tire)
up to 90 kg load*
Front
175 kPa (1.75 kg/cm2, 1.75 bar)
Rear200 kPa (2.00 kg/cm2, 2.00 bar)
90 kg load–maximum
load*
Front
225 kPa (2.25 kg/cm2, 2.25 bar)
Rear225 kPa (2.25 kg/cm2, 2.25 bar)
*Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Type Spoke wheel
Size 18 ´1.60
Rear
Type Spoke wheel
Size 15 M/C ´MT 3.00
Brakes
Front
Type Single disc brake
Operation Right hand operation
Fluid DOT 4Rear
Type Drum brake
Operation Right foot operation
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm
Shock absorber/spring
Front
Type Coil spring / oil damper
Rear
Type Coil spring / oil damper
Wheel travel
Front 140 mm
Rear 100 mm
Electrical system
Ignition system Transistorized coil ignition
(digital)
Charging system
Type A.C. magneto
Standard output 14 V, 23 A @ 5,000 r/min
5JX-9-E0 4/9/0 4:11 AM Page 78