brake light YAMAHA XVS125 2001 Owners Manual

EAU00009
TABLE OF CONTENTS
GIVE SAFETY THE RIGHT OF WAY..................1-1
DESCRIPTION....................................................2-1
Left view.............................................................2-1
Right view..........................................................2-2
Controls and Instruments...................................2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................................................3-1
Main switch/steering lock...................................3-1
Indicator lights....................................................3-2
Speedometer unit..............................................3-2
Anti-theft alarm (optional)...................................3-3
Handlebar switches............................................3-3
Clutch lever........................................................3-5
Shift pedal..........................................................3-5
Brake lever.........................................................3-5
Brake pedal........................................................3-6
Fuel tank cap.....................................................3-6
Fuel....................................................................3-7
Fuel cock............................................................3-7
Starter (choke) lever..........................................3-8
Helmet holder.....................................................3-9
Adjusting the shock absorber assemblies..........3-9
Sidestand.........................................................3-10
Ignition circuit cut-off system............................3-10PRE-OPERATION CHECKS...............................4-1
Pre-operation check list.....................................4-1
OPERATION AND IMPORTANT RIDING
POINTS................................................................5-1
Starting the engine.............................................5-1
Starting a warm engine......................................5-2
Shifting...............................................................5-3
Recommended shift points
(for Switzerland only).......................................5-3
Tips for reducing fuel consumption....................5-4
Engine break-in..................................................5-4
Parking...............................................................5-5
PERIODIC MAINTENANCE AND MINOR
REPAIR................................................................6-1
OwnerÕs tool kit..................................................6-1
Periodic maintenance and lubrication chart.......6-2
Removing and installing panels.........................6-5
Checking the spark plugs...................................6-7
Engine oil and oil filter element..........................6-9
Cleaning the air filter element..........................6-12
Adjusting the carburetor...................................6-14
Adjusting the engine idling speed....................6-14
Adjusting the throttle cable free play................6-15
Adjusting the valve clearance..........................6-15
123
456
5JX-9-E1 9/27/00 10:45 AM Page 5

Tires.................................................................6-15
Spoke wheels..................................................6-18
Adjusting the clutch lever free play..................6-19
Adjusting the brake lever free play...................6-20
Adjusting the brake pedal position and
free play.........................................................6-20
Adjusting the rear brake light switch................6-22
Checking the front brake pads and
rear brake shoes............................................6-22
Checking the brake fluid level..........................6-23
Changing the brake fluid..................................6-24
Drive chain slack..............................................6-25
Lubricating the drive chain...............................6-27
Checking and lubricating the cables................6-27
Checking and lubricating the brake and
shift pedals.....................................................6-28
Checking and lubricating the brake and
clutch levers...................................................6-28
Checking and lubricating the sidestand...........6-29
Checking the front fork.....................................6-29
Checking the steering......................................6-30
Checking the wheel bearings...........................6-30
Battery..............................................................6-31
Replacing the fuses.........................................6-32
Replacing the headlight bulb...........................6-33
Replacing a turn signal light bulb.....................6-35Replacing the tail/brake light bulb....................6-36
Supporting the motorcycle...............................6-37
Front wheel......................................................6-37
Rear wheel.......................................................6-39
Troubleshooting...............................................6-41
Troubleshooting chart......................................6-42
MOTORCYCLE CARE AND STORAGE.............7-1
Care...................................................................7-1
Storage..............................................................7-4
SPECIFICATIONS...............................................8-1
Specifications.....................................................8-1
Conversion table................................................8-5
CONSUMER INFORMATION..............................9-1
Identification numbers........................................9-1
Key identification number...................................9-1
Vehicle identification number.............................9-1
Model label.........................................................9-2
TABLE OF CONTENTS
789
5JX-9-E1 9/27/00 10:45 AM Page 6

PRE-OPERATION CHECKS
1
2
34
5
6
7
8
9
4-2
Throttle grip¥Make sure that operation is smooth.
¥Lubricate throttle grip, housing and cables if necessary.
¥Check free play.
¥If necessary, have Yamaha dealer make adjustment.6-15
Control cables¥Make sure that operation is smooth.
¥Lubricate if necessary.6-27
Drive chain¥Check chain slack.
¥Adjust if necessary.
¥Check chain condition.
¥Lubricate if necessary.6-25Ð6-27
Wheels and tires¥Check for damage.
¥Check tire condition and tread depth.
¥Check air pressure.
¥Correct if necessary.6-15Ð6-18
Brake and shift pedals¥Make sure that operation is smooth.
¥Lubricate pedal pivoting points if necessary.6-28
Brake and clutch levers¥Make sure that operation is smooth.
¥Lubricate lever pivoting points if necessary.6-28
Sidestand¥Make sure that operation is smooth.
¥Lubricate pivot if necessary.6-29
Chassis fasteners¥Make sure that all nuts, bolts and screws are properly tightened.
¥Tighten if necessary.Ñ
Instruments, lights,
signals and switches¥Check operation.
¥Correct if necessary.3-2Ð3-4, 6-33Ð6-36
Sidestand switch¥Check operation of ignition circuit cut-off system.
¥If system is defective, have Yamaha dealer check vehicle.3-10Ð3-11 ITEMCHECKSPAGE
5JX-9-E1 9/27/00 10:45 AM Page 23

PERIODIC MAINTENANCE AND MINOR REPAIR
6
6-4
22Engine oil filter element¥Replace.ÖÖÖ
23
*Front and rear brake
switches¥Check operation.ÖÖÖÖÖÖ
24Moving parts and cables¥Lubricate.ÖÖÖÖÖ
25*Lights, signals and
switches¥Check operation.
¥Adjust headlight beam.ÖÖÖÖÖÖ NO.ITEMCHECK OR MAINTENANCE JOBODOMETER READING (´1,000 km)
ANNUAL
CHECK
16121824
EAU03541
NOTE:
8The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
8Hydraulic brake service
8
Regularly check and, if necessary, correct the brake fluid level.
8
Every two years replace the internal components of the brake master cylinder and caliper, and change the brake
fluid.
8
Replace the brake hoses every four years and if cracked or damaged.
5JX-9-E1 9/27/00 10:45 AM Page 33

1
2
3
4
56
7
8
9
6-22
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU00713
Adjusting the rear brake light
switchThe rear brake light switch, which is
activated by the brake pedal, is prop-
erly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding
the rear brake light switch in place.
To make the brake light come on ear-
lier, turn the adjusting nut in direction
a. To make the brake light come on
later, turn the adjusting nut in direc-
tion b.1.Rear brake light switch
2.Adjusting nut
12
b
a
EAU00720
Checking the front brake
pads and rear brake shoesThe front brake pads and the rear
brake shoes must be checked for
wear at the intervals specified in the
periodic maintenance and lubrication
chart.
EW000106
w8After adjusting the drive chain
slack or removing and
installing the rear wheel,
always check the brake pedal
free play.
8If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this
adjustment.
8After adjusting the brake pedal
free play, check the operation
of the brake light.
5JX-9-E1 9/27/00 10:45 AM Page 51

1
2
3
4
56
7
8
9
6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
1.Axle nut
1
2.To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction a. To
loosen the drive chain, turn the
adjusting nut at each end of the
swingarm in direction b, and
then push the rear wheel for-
ward.NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.1.Drive chain adjusting nut
2.Alignment marks
3.Locknut
3
1
2
ba
EC000096
cCImproper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.3.Tighten both locknuts, and then
tighten the axle nut to the speci-
fied torque.
4.Adjust the brake pedal free play.
(See page 6-21 for brake pedal
free play adjustment proce-
dures.)
EW000103
wAfter adjusting the brake pedal
free play, check the operation of
the brake light.
Tightening torque:
Axle nut:
104 Nm (10.4 mákg)
5JX-9-E1 9/27/00 10:45 AM Page 55

1
2
3
4
56
7
8
9
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
2.Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3.Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4.Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.1.Bulb
1
2
1
EAU01623
Replacing the tail/brake light
bulb1.Remove the tail/brake light lens
by removing the screws.1.Lens
2Screw (´2)
1
2.Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3.Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4.Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.1.Bulb
5JX-9-E1 9/27/00 10:45 AM Page 65

1
2
3
4
56
7
8
9
6-40
PERIODIC MAINTENANCE AND MINOR REPAIR
5.Loosen the locknut and the drive
chain adjusting nut on both ends
of the swingarm.
6.Remove the axle nut, and then
pull the wheel axle out.
7.Push the wheel forward, and
then remove the drive chain from
the rear sprocket.NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.8.Remove the wheel.1.Locknut
2.Drive chain adjusting nut
3.Wheel axle
1
32
EAU03190
To install the rear wheel
1.Insert the wheel axle from the
left-hand side, and then install
the drive chain onto the rear
sprocket.
2.Install the axle nut, and then
lower the rear wheel so that it is
on the ground.
3.Install the brake rod onto the
brake camshaft lever, and then
install the brake pedal free play
adjusting nut onto the brake rod.
4.Connect the brake torque rod to
the brake shoe plate by installing
the bolt and the nut, and then
tighten the bolt to the specified
torque.
5.Adjust the drive chain slack.
(See page 6-25 for drive chain
slack adjustment procedures.) Tightening torque:
Brake torque rod bolt:
23 Nm (2.3 mákg)
6.Tighten the axle nut to the speci-
fied torque.
7.Adjust the brake pedal position
and free play. (See page 6-20 for
brake pedal position and free
play adjustment procedures.)
EW000103
wAfter adjusting the brake pedal
free play, check the operation of
the brake light.
Tightening torque:
Axle nut:
104 Nm (10.4 mákg)
5JX-9-E1 9/27/00 10:45 AM Page 69

1
2
3
4
5
67
8
9
7-2
MOTORCYCLE CARE AND STORAGE
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or elec-
trolyte.
8Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of
wheel and swingarm bearings,
fork and brakes), electric com-
ponents (couplers, connec-
tors, instruments, switches
and lights), breather hoses
and vents.8For motorcycles equipped
with a windshield: Do not use
strong cleaners or hard
sponges as they will cause
dulling or scratching. Some
cleaning compounds for plas-
tic may leave scratches on the
windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If
the windshield is scratched,
use a quality plastic polishing
compound after washing.
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas.
Stubborn dirt and insects will come
off more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.After riding in the rain, near the sea
or on salt-sprayed roadsSince sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter
may remain well into spring.1.Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
cCDo not use warm water since it
increases the corrosive action of
the salt.2.After drying the motorcycle,
apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
5JX-9-E1 9/27/00 10:45 AM Page 73

8
SPECIFICATIONS
8-4
Battery
TypeGT6B-3
Voltage, capacity12 V, 6 Ah
Headlight typeHalogen bulb
Bulb voltage, wattage ´quantity
Headlight12 V, 60/55 W ´1
Tail/brake light12 V, 5/21 W ´1
Front flasher light12 V, 21 W ´2
Rear flasher light12 V, 21 W ´2
Auxiliary light12 V, 4 W ´1
Meter lighting12 V, 1.7 W ´1
Neutral indicator light12 V, 1.7 W ´1
High beam indicator light12 V, 1.7 W ´1
Turn indicator light12 V, 1.7 W ´1
Engine indicator light12 V, 1.7 W ´1
Fuses
Main fuse30 A
Headlight fuse15 A
Signaling system fuse10 A
Ignition fuse10 A
Carburetor heater fuse10 A
5JX-9-E1 9/27/00 10:45 AM Page 80