light YAMAHA XVS950 2009 Owner's Guide

MOTORCYCLE CARE AND STORAGE
7-2
2
3
4
5
6
78
9 off any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
TIP

Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE:
Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]

2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-

MOTORCYCLE CARE AND STORAGE
7-3
1
2
3
4
5
6
7
8
9
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted and chrome-plat-
ed surfaces. Avoid combination
cleaner waxes, many of which
contain abrasives that may mar
the paint or protective finish.
7. Let the motorcycle dry completely
before storing or covering it.
WARNING

EWA11131
Contaminants on the brakes or tires
can cause loss of control.

Make sure that there is no oil or
wax on the brakes or tires.

If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
NOTICE

ECA10950

Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.

Never apply oil or wax to the
drive belt.

Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.

Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP


Consult a Yamaha dealer for ad-
vice on what products to use.

Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
EAU26281
Storage
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
NOTICE

ECA10810

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the

SPECIFICATIONS
8-3
1
2
3
4
5
6
7
8
9

Voltage, capacity:
12 V, 11.2 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage
×× × ×
quantity:
Headlight:
12 V, 60 W/55 W
×
1
Tail/brake light:
12 V, 5.0 W/21.0 W
×
1
Front turn signal light:
12 V, 21.0 W
×
1
Rear turn signal light:
12 V, 21.0 W
×
2
Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Oil level warning light:
LED
Turn signal indicator light:
LED
Fuel level warning light:
LED
Engine trouble warning light:
LED
Immobilizer system indicator light:
LED

Fuses:
Main fuse:
40.0 AHeadlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Parking lighting fuse:
10.0 A
Fuel injection system fuse:
10.0 A
Backup fuse:
10.0 A

INDEX
A
Air filter element, replacing ...................... 6-11
Auxiliary light bulb, replacing ................... 6-31
B
Battery ..................................................... 6-24
Brake and clutch levers, checking and
lubricating .............................................. 6-21
Brake and shift pedals, checking and
lubricating .............................................. 6-21
Brake fluid, changing ............................... 6-18
Brake fluid level, checking ....................... 6-17
Brake lever .............................................. 3-10
Brake lever free play, adjusting ............... 6-15
Brake pedal ............................................. 3-10
C
Cables, checking and lubricating ............. 6-20
Care ........................................................... 7-1
Catalytic converter ................................... 3-12
Clutch lever................................................ 3-9
Clutch lever free play, adjusting .............. 6-14
D
Dimmer switch ........................................... 3-8
Drive belt slack ........................................ 6-18
E
Engine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-11
Engine oil and oil filter cartridge ................ 6-7
Engine stop switch..................................... 3-8
Engine trouble warning light ...................... 3-4
F
Front and rear brake pads, checking ....... 6-16
Front fork, checking ................................. 6-23
Fuel.......................................................... 3-11
Fuel consumption, tips for reducing........... 5-3Fuel level warning light .............................. 3-4
Fuel tank cap ........................................... 3-10
Fuses, replacing ...................................... 6-26
H
Handlebar switches ................................... 3-7
Hazard switch ............................................ 3-8
Headlight bulb, replacing ......................... 6-27
Helmet holder .......................................... 3-14
High beam indicator light ........................... 3-3
Horn switch................................................ 3-8
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-16
Immobilizer system.................................... 3-1
Immobilizer system indicator light ............. 3-4
Indicator and warning lights....................... 3-3
K
Key identification number .......................... 9-1
L
License plate light bulb, replacing ........... 6-30
M
Main switch/steering lock .......................... 3-2
Maintenance and lubrication, periodic ....... 6-3
Maintenance, emission control system ..... 6-2
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function meter unit ............................ 3-4
N
Neutral indicator light................................. 3-3
O
Oil level warning light ................................ 3-3
P
Panel, removing and installing .................. 6-6Parking ...................................................... 5-4
Part locations ............................................ 2-1
Pass switch ............................................... 3-8
R
Rear brake light switch, adjusting ........... 6-16
Rear suspension, lubricating................... 6-22
RESET switch ........................................... 3-9
Rider seat................................................ 3-13
S
Safety information ..................................... 1-1
SELECT switch ......................................... 3-8
Shifting ...................................................... 5-2
Shift pedal ................................................. 3-9
Shock absorber assembly, adjusting ...... 3-14
Sidestand ................................................ 3-16
Sidestand, checking and lubricating ....... 6-22
Spark plugs, checking ............................... 6-6
Specifications ............................................ 8-1
Starting the engine .................................... 5-1
Start switch ............................................... 3-8
Steering, checking .................................. 6-23
Storage ..................................................... 7-3
Supporting the motorcycle ...................... 6-31
T
Tail/brake light bulb, replacing ................ 6-28
Throttle cable free play, checking ........... 6-12
Throttle grip and cable, checking and
lubricating ............................................. 6-20
Tires ........................................................ 6-12
Tool kit ...................................................... 6-1
Troubleshooting ...................................... 6-32
Troubleshooting chart ............................. 6-33
Turn signal indicator light .......................... 3-3
Turn signal light bulb, replacing .............. 6-29