low beam YAMAHA YBR125 2007 Owners Manual

INSTRUMENT AND CONTROL FUNCTIONS
3-2
1. Turn indicator light “ ”
2. Neutral ”N”
3. High beam.Indicator light “ ” 1. Speedometer
2. Odometer1. Fuel gauge
1
1
2SpeedometerThe speedometer shows riding
speed.
This speedometer is equipped with
an odometer.
Fuel gaugeThe fuel gauge indicates the quantity
of the remaining petrol in the fuel tank.
The gauge needle moves from “F”
(Full) to"E”(Empty) as the fuel level
decreases.
When the needle comes below “E”
please refill the fuel tank at the
earliest.
Indicator lights1. Turn indicator light " "
2. Neutral indicator light "N"
3. High beam indicator light " "The indicator flashes when the
turn switch is moved to the left or
right. .
This indicator comes on when the
transmission is in neutral.
This indicator comes on when the
headlight high beam is used.
1
2
3

Turn signal switch
Horn switch " "
Lights switch To signal a right-hand turn, push the
switch to " ". To signal a left-
hand turn, push the switch to " ".
Once the switch is released it will
return to the center position. To
cancel the signal, push the switch in
after it has returned to the center
position.
Press the switch to sound the horn.
Turning the light switch to " ",
turns on the meter light and tail-light.
Turning the light switch to “ ",
turns the headlight on also.
1. Clutch leverClutch leverThe clutch lever is located on the left
handlebar. Pull the clutch lever to
the handlebar to disengage the
clutch, and release the lever to
engage the clutch. The lever should
be pulled rapidly and released slowly
for smooth clutch operation.
INSTRUMENT AND CONTROL FUNCTIONS
3-3
1. PassSwitch " "
2. Dimmer Switch
3. Light switch
4. Turn signal cum cancellation switch“ “
5. Horn switchHandlebar switchesDimmer switch
Turn the switch to" " for the high
beam and to " " for the low beam. Pass switch""
Press the switch to operate the
Passing Light.
1
1
2
3
4 5

1. Screw (2 Nos.)
2. Bolt (1Headlight bulb replacementIf the headlight bulb burns out,
replace the bulb as follows:
1. Remove the two screws from the
Head Light.
2. Loosen bolt.
3. Remove head light bezel assy.
Forward.
No.)1. Bulb holder
3. Remove headlight bulb holder
from bezel
1. Bulb (Halogen)Keep flammable products and
your hands away from the bulb
while it is on, as it is hot. Do not
touch the bulb until it cools down.
4. Remove the defective bulb.
5. Put a new bulb into position and
secure it in place with the bulb
holder.
6. Install the Head Light Assy.
7. If the headlight beam adjustment
is necessary, ask a YAMAHA
dealer to make adjustment.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
WARNING
1

PRE-DELIVERY INSPECTION REPORT10-4
C. ELECTRICAL
a. Ignition Switch Operation
b. Left Hand Switch Operation & Pass Beam
• Horn
• Indicator• Head Light
c. All Bulbs - Functioningd. Battery
• Electrolyte Level
• Specific Gravity• Routing of Breather Pipe• Fuse• Routing of Positive Wire (Red) Below Breather Pipe
D. ROAD TEST
a. Starting
b. Gear Shifting Operationc. Clutch Operationd. Application of Brakes (Front and Rear)e. Speedo/ Odo Meter Operationf. Fuel gauge OperationEXPLAINED BYSIGNATURE: _____________ NAME:
CUSTOMER’S SIGN
MAIN SELLING DLR’S STAMP, SIGNATURE
service2.pmd11/3/2006, 8:50 PM 4