check engine YAMAHA YD110 2005 User Guide

The exhaust gas of an Engine pollutes air with such gases which are very dangerous for mankind. In order to ensure
clean and healthy environment, strict regulations have been enforced to control pollution. As per regulations ‘CO’
emissions by petrol driven Two Wheelers must be less than 3.5% (by volume) during Idling of the Engine.fudkl çokg fu;a=k.k ls lacf/kr rF;% batu ls ckgj fudyus okyh xSl gok d¨ mu xSl¨ ls çnwf"kr dj nsrk gS t¨ ekuo thou
ds fy, cgqr [krjukd gSA blh lanHkZ esa lkQ v©j LoLFk okrkoj.k d¨ lqfuf'pr djus ds fy, çnw"k.k fu;a=k.k gsrq l[r dkuwu¨
dk çko/kku fd;k x;k gSA bUgh dkuwu¨ ds rgr iSVª¨y ls nqifg;k okgu¨ ds batu ds [kkyh pyus dh voLFkk esa lhñv¨ñ dk çokg3.5%
ls de g¨uk pkfg,A
Non Compliance with emission standards is treated as a punishable offence.çekf.kd çokg ds vuqlkj vlg;¨x djus d¨ n.MkRed vijk/k dh rjg ekuk tkrk gSAAs a Manufacture, YAMAHA MOTOR INDIA PVT. LTD. ensure that your Vehicle meets the exhaust emission
standards before leaving the Factory.,d fuekZrk ds :i esa ;kekgk e¨Vj bafM;k fyfeVsM ;g lqfuf'pr djrk gS fd vkidh e¨VjlkbZfdy QSDVªh ls ckgj vkus ls igys
fudkl çokg dh çekf.kdrkv¨a d¨ gj rjg ls iwjk djrk gSAPlease note that when new, the Vehicle has a Factory tuned Carburetor, where the Air Screw is optimally adjusted to
meet the requirement of exhaust emission. This screw must not be tampered with as it may cause variation in pre-
controlled ‘CO’ emission levels. Subsequently, it becomes very important that it should always be within the recom-
mended limit, when checked by a properly calibrated ‘CO’ Measuring Equipment.ÑI;k /;ku j[ksa] u;h g¨usa ds dkj.k e¨VjlkbZfdy esa QSDVªh esa gh lSV x;k dkc¨ZjsVj yxk g¨rk gS] tgk¡ bls ,DtkWLV ¼fudkl½&çokg
ds eqrkfod dk;kZuqlkj ,MtLV fd;k tkrk gSA dkc¨ZjsVj ds lkFk fdlh rjg dh NsM+&NkM+ ugh dh tkuh pkfg,] D;¨fd ,slk
djus ls iwoZ&fu;a=k.k dkcZu&e¨u¨vkWDlkbM ds çokg ds Lrj¨a esa fHkérk vk ldrh gSA lkFk gh] ;g cgqr vko';d g¨ tkrk gS
fd tc bls lgh rjhds ls dSyhcjsV ¼iM+rky½ fd, x, dkcZu&e¨u¨vkWDlkbM eki&midj.k ls tk¡pk tk, vkSj ;g ges'kk çLrkfod
lhek ds vUnj gh g¨uk pkfg,AFACTS RELATED WITH EXHAUST EMISSION CONTROL
9.2
çokg&fu;a=k.k ls lacf/kr rF;
pg56_96.pmd2/25/2005, 9:59 AM 95

If the owner of the Vehicle does not comply with above legal requirement, the Vehicle may be
deregistered or penalty may be imposed by the authorities.;fn okgu&ekfyd mij¨Dr dkuwuh ek¡x d¨ Lohdkj ugh djrk gS r¨ okgu dk iathdj.k jí g¨ ldrk gS vFkok ml
ij tqekZuk yxk;k tk ldrk gSAThe following points may be checked and suitable corrective action if required, to ensure emission levels to remain
within acceptable limits.,eh'ku Lrjksa dks Lohdkjh; lhekvksa ds varxZr cuk;s j[kus ds fy, fuEufyf[kr rF;ksa dj tk¡p djsa o vko';d gks rks la'kks/ku
ds yh, dk;Zokgh djsaA1. Clean and oil Air Filter Element periodically and replace it when required.
le;≤ ij ,;j fQYVj ds ,syhesaV d¨ lkQ djsa v©j blesa rsy Mkyrs jgsa rFkk tc vko';drk iMs+ r¨ bls cny nsaA
2. Clean, inspect and adjust spark Plug Gap periodically.
le;≤ ij LikdZ Iyx dh tk¡p djsa] bls lkQ djsa v©j blds xSi ¼varj½ d¨ ,MtLV djsaA
3. Use only recommended Spark Plug. Replace it as per recommendations.
dsoy çLrkfor LikdZ Iyx dk gh ç;¨x djsaA çLrkfod ekin.M¨ ds vuq:i gh u;k Iyx yxk;saA
4. Use only recommended grade (SG) of genuine engine oil of superior quality.
dsoy mPp DokfyVh dk çLrkfor xzsM ¼
SG
½ dk vlyh batu rsy gh ç;¨x djsaA
5. Get your Vehicle serviced and turned periodically as per recommended schedule.
çLrkfor f'kM~;wy ds eqrkfcd le;≤ ij vius okgu dh l£ol v©j V~;w¯ux djkrs jgsaA
6. Use unadulterated Petrol.
feykoV jfgr iSVª¨y dk ç;¨x djsaaA SAFETY NORMS
9.3
lqj{kk&flðk¡r
pg97_103.pmd2/25/2005, 9:59 AM 97

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd2/25/2005, 10:00 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd2/25/2005, 10:00 AM 10

JOBS TO BE CARRIED OUT DURING TENTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-12
DETWHITE.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING NINTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy
operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if
necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork,
Front & Rear Wheel Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
VALIDITY
KMSDATE OF
SERVICESERVICE DEALER
STAMP
7
PAID
8
PAID12500 - 13000
14500 - 15000 PAID SERVICE RECORD
10-14
DETWHITE.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING EIGHTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-16
DETGREEN.pmd2/25/2005, 10:00 AM 12