engine oil YAMAHA YD110 2005 User Guide

CAUTION :
Make sure the air filter is
properly seated in the air filter
case.
 The engine should never be run
without the air filter installed.
Excessive piston and/or
cylinder wear may result.
 Dirty Element Air Cleaner
caused excessive fuel
consumption and loss of
power.
 Clean Element Air Cleaner after
every 2000 kms.
 The Element Air Cleaner should
be cleaned and lubricated more
frequently (every 1000 km,s), if
Motorcycle is operated in very
dusty (e.g. unpaved, dust laden
roads) conditions. lko/kkuh %
;g lqfufpr djsa fd ,;j&fQYVj
lgh tk,A
6. Apply recommended oil to the
entire surface of the each
element and squeeze out the
excess oil. They should be wet
but not dripping.
çR;sd ewy Hkkx dh van#uh lrg ij
çLrkfod rsy gh yxk, v©j Qkyrw
rsy ds fupksM+ ysA os ¼ewy Hkkx½ xhys
gksus pkfg, u fd rsy esa Mwcs gq,A
Recommended oil
çLrkfod rsy :20W40 type SG
7. Pull the air filter elements over
the frame and install the air filter
in the case.
,;j&fQYVj ds ,yhesaV ¼ewy&fgLlksa½
dks Ýse ds Åij ls [khap ys rFkk
,;j&fQYVj dks dsl ds vanj yxk
nsaA
8. Install the Spring Wire.
¯Lçx okW;j Hkh yxk,¡A
9. Install the air filter case cover and
panel
,;j&fQYVj dsl ds doj v©j iSuy
dks yxk nsaA
6.15
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
PG1_55.pmd2/25/2005, 10:04 AM 51

2.
b±/ku dh [kkyh Vadh dks ckgj fudky
ysa] Vadh esa ,d di
SAE 10W30 or
20W40
czkaM dk eksVj vkW;y Mkysaa]
fQj Vadh ds van:uh lrg dh dks¯Vx
djus ds fy, Vadh dks vPNh rjg ls
fgyk,a vkSj Qkyrw rsy dks ckgj fudky
nsaA Vadh dks fQj ls ;FkkLFkku ij
yxk nsaA
3. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil in the
spark plug hole. Reinstall spark
plug. Kick the engine over several
times (with the ignition off) to coat
the cylinder wall with oil.
LikWdZ Iyx dks ckgj fudky ys]
SAE
10W30 or 20W40
czkaM dk ,d cM+k
pEep LikWdZ Iyx ds Nsn esa ¼gksy½
Mkysa vkSj bls fQj ls okil yxk nsaA
batu dks dqN le; rd fdd yxkrs
jgsa ¼bXuh'u dks can j[krs gq,½ ftlls
flyh.Mj dh fnokjksa dh vkW;y&dks¯Vx
gks tk,A
4. Remove the drive chain.
Thoroughly clean the chain
withsolvent and lubricate it.
Reinstall the chain or store it in a
B. STORAGEch- Hk.Mkj.k ¼LVksjst½Long term storage (60 days or more)
of your Motorcycle will require more
preventive procedures to guard
against deterioration. After thoroughly
cleaning the Motorcycle, prepare for
storage as follows:vkidh eksVjlkbfdy dks yEch vof/k rd
¼60
fnu ;k mlls Åij½ ^LVksj* djds
j[kus ij bls u"V gksus ls cpkus ds fy,
lko/kkuho'k dqN izfØ;k,a viukuh iM+rh
gSaA eksVjlkbfdy dks iwjh rjg lQkbZ
djus ds ckn] fuEufyf[kr ckrkssa dk vuqlj.k
djds] bls ^LVksj* djus dh rS;kjh djsa %
1. Drain the fuel tank, fuel lines, and
carburetor float bowl.
b±/ku dh Vadh] b±/ku dh ykbZuksa] vkSj
dkjC;wjsVj ds ¶yksV&ckÅy dks [kkyh
djs ysaA
2. Remove the empty fuel tank, pour
a cup of SAE 10W30 or 20W40
motor oil in the tank, shake the
tank to coat the inner surfaces tank
to coat the inner surfaces
thoroughly and drain off the excess
oil. Reinstall the tank.plastic bag (tied to frame for
safekeeping).
M ªkbo&pSu dks ckgj fudky ysaA
bls iwjh rjg ls nzkod ¼lkWYosaV½ ls
lkQ djsa vkSj bl ij xzhl bR;kfn
yxk nsaA pSu dks fQj ls yxk nsa
vFkok bls ,d IykWfLVd & cSx esa
^LVksj* djds j[k ysaA ¼lqjf{kr j[kus
ds fy, Ýse ds lkFk cka/k nsa½A
5. Lubricate all control cables.
lHkh daVªksy&dscyksa ¼rkjksa½ dh xzh¯lx
dj ysaA
6. Block up the frame to raise both
wheels off the ground.
nksuksa ifgvksa dks t+ehu ls Åij mBkus
ds fy, Ýse dks jksddj j[ksaA
7. Tie a plastic bag over the
exhaust pipe outlet to prevent
moisture from entering.
ueh dks ^,XtkWLV&ikbi* ¼fudkl&uyh½
ds vanj vkus ls cpkus dss fy, ikbi
dks ckgj ls IykWfLVd cSx ls ¼yisV½ nsaA
CLEANING AND STORAGElQkbZ rFkk HkaMkj.k
7.3
pg56_96.pmd2/25/2005, 9:59 AM 86

SPECIFICATIONS
ModelCRUX S
Dimensions:
Overall length2,000 mm
Overall width 735 mm
Overall height1,075 mm
Seal height 780 mm
Wheelbase1,260 mm
Ground clearance160 mm
Minimum turning radius 2,000 mm
Weight : ( With oil & 90% fuel ) 113 kg
Engine :Engine type Air cooled 4-stroke,
SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement105.6 cm
3
Boer × Stroke49×56 mm
Compression ratio9.0 : 1
Starting systemKick starter
Lubrication systemWet sump
Maximum power7.60BHP(5.59kw) @ 7500 RPM
Maximum torque 0.8 Mkg @ 6000 RPM
EngineOil
Type:
CAUTION :
Be sure to use motor oils that do not contain
antifrication modifiers. Passenger car motor oils
(often labelled Energy conserving) contain anti-
friction additives which will cause clutch/or
starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity :
Periodic oil change 0.9 L
Total amount 1.1 L
Air filter:Foam type element
Fuel :
Type Regular gasoline
(petrol)
Fuel tank capacity 11.0 Litres
Reserve amount1.4 Litres
Carburetor:
Type VM17SH
ManufactureMIKUNI
SPECIFICATIONSfo'ks"k fooj.k
8.1
YAMALUBE
4-Stroke motor oil (20W40)
Type SG
pg56_96.pmd2/25/2005, 9:59 AM 88

If the owner of the Vehicle does not comply with above legal requirement, the Vehicle may be
deregistered or penalty may be imposed by the authorities.;fn okgu&ekfyd mij¨Dr dkuwuh ek¡x d¨ Lohdkj ugh djrk gS r¨ okgu dk iathdj.k jí g¨ ldrk gS vFkok ml
ij tqekZuk yxk;k tk ldrk gSAThe following points may be checked and suitable corrective action if required, to ensure emission levels to remain
within acceptable limits.,eh'ku Lrjksa dks Lohdkjh; lhekvksa ds varxZr cuk;s j[kus ds fy, fuEufyf[kr rF;ksa dj tk¡p djsa o vko';d gks rks la'kks/ku
ds yh, dk;Zokgh djsaA1. Clean and oil Air Filter Element periodically and replace it when required.
le;≤ ij ,;j fQYVj ds ,syhesaV d¨ lkQ djsa v©j blesa rsy Mkyrs jgsa rFkk tc vko';drk iMs+ r¨ bls cny nsaA
2. Clean, inspect and adjust spark Plug Gap periodically.
le;≤ ij LikdZ Iyx dh tk¡p djsa] bls lkQ djsa v©j blds xSi ¼varj½ d¨ ,MtLV djsaA
3. Use only recommended Spark Plug. Replace it as per recommendations.
dsoy çLrkfor LikdZ Iyx dk gh ç;¨x djsaA çLrkfod ekin.M¨ ds vuq:i gh u;k Iyx yxk;saA
4. Use only recommended grade (SG) of genuine engine oil of superior quality.
dsoy mPp DokfyVh dk çLrkfor xzsM ¼
SG
½ dk vlyh batu rsy gh ç;¨x djsaA
5. Get your Vehicle serviced and turned periodically as per recommended schedule.
çLrkfor f'kM~;wy ds eqrkfcd le;≤ ij vius okgu dh l£ol v©j V~;w¯ux djkrs jgsaA
6. Use unadulterated Petrol.
feykoV jfgr iSVª¨y dk ç;¨x djsaaA SAFETY NORMS
9.3
lqj{kk&flðk¡r
pg97_103.pmd2/25/2005, 9:59 AM 97

NON- CLAIMABLE
This coupon entitles the owner to the paid service as detailed overleaf
and is mandatory for
eligibility of warranty benefits.
Cost of Oil & Gaskets will be chargeable at actuals.
No.
SELLING DLR'S STAMP, SIGN & CODESERVICING DLR'S STAMP, SIGN & CODE
CUSTOMER'S CERTIFICATION
The jobs as detailed overleaf have been
executed to my entire satisfaction.
Sig. :
Name :FRAME NO. :
ENGINE NO. :
DATE OF SALE :JOB CARD NO :SERVICE DATE :KILOMETERS :VALIDITY : WITHIN 28500-29000 KMS FROM THE DATE OF PURCHASE OF MOTORCYCLE
OR WITHIN 60 DAYS FROM PREVIOUS SERVICE WHICHEVER IS EARLIER.
15
FIFTEENTH PAID SERVICE COUPON
SERVICING DEALER TO ENSURE THAT SERVICE RECORD IS DULY ENTERED ON PAGE 10-41.
10-1
DETGREEN.pmd2/25/2005, 10:00 AM 1

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

NON- CLAIMABLE
This coupon entitles the owner to the paid service as detailed overleaf
and is mandatory for
eligibility of warranty benefits.
Cost of Oil & Gaskets will be chargeable at actuals.
No.
SELLING DLR'S STAMP, SIGN & CODESERVICING DLR'S STAMP, SIGN & CODE
CUSTOMER'S CERTIFICATION
The jobs as detailed overleaf have been
executed to my entire satisfaction.
Sig. :
Name :FRAME NO. :
ENGINE NO. :
DATE OF SALE :JOB CARD NO :SERVICE DATE :KILOMETERS :
FOURTEENTH PAID SERVICE COUPON
14
VALIDITY : WITHIN 26500-27000 KMS FROM THE DATE OF PURCHASE OF MOTORCYCLE
OR WITHIN 60 DAYS FROM PREVIOUS SERVICE WHICHEVER IS EARLIER.
SERVICING DEALER TO ENSURE THAT SERVICE RECORD IS DULY ENTERED ON PAGE 10-41.
10-3
DETGREEN.pmd2/25/2005, 10:00 AM 3

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

NON- CLAIMABLE
This coupon entitles the owner to the paid service as detailed overleaf
and is mandatory for
eligibility of warranty benefits.
Cost of Oil & Gaskets will be chargeable at actuals.
No.
SELLING DLR'S STAMP, SIGN & CODESERVICING DLR'S STAMP, SIGN & CODE
CUSTOMER'S CERTIFICATION
The jobs as detailed overleaf have been
executed to my entire satisfaction.
Sig. :
Name :FRAME NO. :
ENGINE NO. :
DATE OF SALE :JOB CARD NO :SERVICE DATE :KILOMETERS :
THIRTEENTH PAID SERVICE COUPON
VALIDITY : WITHIN 24500-25000 KMS FROM THE DATE OF PURCHASE OF MOTORCYCLE
OR WITHIN 60 DAYS FROM PREVIOUS SERVICE WHICHEVER IS EARLIER.
13
SERVICING DEALER TO ENSURE THAT SERVICE RECORD IS DULY ENTERED ON PAGE 10-41.
10-5
DETGREEN.pmd2/25/2005, 10:00 AM 5

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6