fuel YAMAHA YD110 2005 Owner's Manual

2.
b±/ku dh [kkyh Vadh dks ckgj fudky
ysa] Vadh esa ,d di
SAE 10W30 or
20W40
czkaM dk eksVj vkW;y Mkysaa]
fQj Vadh ds van:uh lrg dh dks¯Vx
djus ds fy, Vadh dks vPNh rjg ls
fgyk,a vkSj Qkyrw rsy dks ckgj fudky
nsaA Vadh dks fQj ls ;FkkLFkku ij
yxk nsaA
3. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil in the
spark plug hole. Reinstall spark
plug. Kick the engine over several
times (with the ignition off) to coat
the cylinder wall with oil.
LikWdZ Iyx dks ckgj fudky ys]
SAE
10W30 or 20W40
czkaM dk ,d cM+k
pEep LikWdZ Iyx ds Nsn esa ¼gksy½
Mkysa vkSj bls fQj ls okil yxk nsaA
batu dks dqN le; rd fdd yxkrs
jgsa ¼bXuh'u dks can j[krs gq,½ ftlls
flyh.Mj dh fnokjksa dh vkW;y&dks¯Vx
gks tk,A
4. Remove the drive chain.
Thoroughly clean the chain
withsolvent and lubricate it.
Reinstall the chain or store it in a
B. STORAGEch- Hk.Mkj.k ¼LVksjst½Long term storage (60 days or more)
of your Motorcycle will require more
preventive procedures to guard
against deterioration. After thoroughly
cleaning the Motorcycle, prepare for
storage as follows:vkidh eksVjlkbfdy dks yEch vof/k rd
¼60
fnu ;k mlls Åij½ ^LVksj* djds
j[kus ij bls u"V gksus ls cpkus ds fy,
lko/kkuho'k dqN izfØ;k,a viukuh iM+rh
gSaA eksVjlkbfdy dks iwjh rjg lQkbZ
djus ds ckn] fuEufyf[kr ckrkssa dk vuqlj.k
djds] bls ^LVksj* djus dh rS;kjh djsa %
1. Drain the fuel tank, fuel lines, and
carburetor float bowl.
b±/ku dh Vadh] b±/ku dh ykbZuksa] vkSj
dkjC;wjsVj ds ¶yksV&ckÅy dks [kkyh
djs ysaA
2. Remove the empty fuel tank, pour
a cup of SAE 10W30 or 20W40
motor oil in the tank, shake the
tank to coat the inner surfaces tank
to coat the inner surfaces
thoroughly and drain off the excess
oil. Reinstall the tank.plastic bag (tied to frame for
safekeeping).
M ªkbo&pSu dks ckgj fudky ysaA
bls iwjh rjg ls nzkod ¼lkWYosaV½ ls
lkQ djsa vkSj bl ij xzhl bR;kfn
yxk nsaA pSu dks fQj ls yxk nsa
vFkok bls ,d IykWfLVd & cSx esa
^LVksj* djds j[k ysaA ¼lqjf{kr j[kus
ds fy, Ýse ds lkFk cka/k nsa½A
5. Lubricate all control cables.
lHkh daVªksy&dscyksa ¼rkjksa½ dh xzh¯lx
dj ysaA
6. Block up the frame to raise both
wheels off the ground.
nksuksa ifgvksa dks t+ehu ls Åij mBkus
ds fy, Ýse dks jksddj j[ksaA
7. Tie a plastic bag over the
exhaust pipe outlet to prevent
moisture from entering.
ueh dks ^,XtkWLV&ikbi* ¼fudkl&uyh½
ds vanj vkus ls cpkus dss fy, ikbi
dks ckgj ls IykWfLVd cSx ls ¼yisV½ nsaA
CLEANING AND STORAGElQkbZ rFkk HkaMkj.k
7.3
pg56_96.pmd2/25/2005, 9:59 AM 86

SPECIFICATIONS
ModelCRUX S
Dimensions:
Overall length2,000 mm
Overall width 735 mm
Overall height1,075 mm
Seal height 780 mm
Wheelbase1,260 mm
Ground clearance160 mm
Minimum turning radius 2,000 mm
Weight : ( With oil & 90% fuel ) 113 kg
Engine :Engine type Air cooled 4-stroke,
SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement105.6 cm
3
Boer × Stroke49×56 mm
Compression ratio9.0 : 1
Starting systemKick starter
Lubrication systemWet sump
Maximum power7.60BHP(5.59kw) @ 7500 RPM
Maximum torque 0.8 Mkg @ 6000 RPM
EngineOil
Type:
CAUTION :
Be sure to use motor oils that do not contain
antifrication modifiers. Passenger car motor oils
(often labelled Energy conserving) contain anti-
friction additives which will cause clutch/or
starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity :
Periodic oil change 0.9 L
Total amount 1.1 L
Air filter:Foam type element
Fuel :
Type Regular gasoline
(petrol)
Fuel tank capacity 11.0 Litres
Reserve amount1.4 Litres
Carburetor:
Type VM17SH
ManufactureMIKUNI
SPECIFICATIONSfo'ks"k fooj.k
8.1
YAMALUBE
4-Stroke motor oil (20W40)
Type SG
pg56_96.pmd2/25/2005, 9:59 AM 88

WARRANTY
9.6
okjaVh
The claim for exchange or repair of part (s) shall be considered only when:ikVZl d¨ cnyus vFkok budh fjis;j djus ds Dyse ij rHkh fopkj fd;k tk,xk tc %1. Customer ensures that immediately upon discovery of the defect he
approaches the nearest YMI Authorised Dealership with the affected
Motorcycle.
The expenses if any, to bring the Motorcycle to the YMI Authorised
Dealership shall be borne by the customer.
miHkksDrk ;g vk'oklu nsrk gS fd n¨"k dk irk yxus ds rqqjUr ckn og e¨VjlkbZfdy
ds lkFk utnhd ds okbZñ,eñvkbZñ Mhyj ds ikl igq¡p tk,xkA
e¨VjlkbZfdy dks vf/kÎÑr Mhyj ds ikl ys tkus dk fdlh rjg dk [kpZ] miHkksDrk
}kjk Lo;a lgu fd;k tk,xkA
2. Customer produces the Owner’s Manual in original to enable the YMI
Dealer to verify the Motorcycle details and servicing details.
eksVjlkbZfdy v©j mldh *l£o¯lx^ dh foLr r tkudkjh nsus ds fy, miHkksDrk dks
okbZñ,eñvkbZñ Mhyj d¨ vksulZ eSuqvy dh ewy izrh çLrqr djuh gksxhA
THIS WARRANTY IS NOT APPLICABLE TO;g *okjaVh^ mu ifjfLFkfr;ksa esa vuqdwy ugh jgsaxh tSls %1. Normal maintenance operations such as Engine tune-up, Decarbonising,
Fuel System Cleaning, Wheels, Brakes and Clutch adjustments as
well as any other normal adjustment.
;g okjaVh dojst dsoy rHkh ykxw gksxk tc eksVjlkbZfdy dks vf/kÑr Mhyj
}kjk lHkh eq¶r l£ol] cksul Ýh l£ol v©j isM l£ol çLrkfod l£ol varjky
esa djokbZ xbZ gks tks fd bl iqfLrdk ds i "B
10-39 ls 10-41 esa fn;k x;k
gS rFkk dsoy okbZñ,eñvkbZñ ds vf/kÑr&ikVZl~ o ;kekY;wc dk ç;ksx fd;k x;k
gksA ÑI;k ;g lqfuf'pr djsa fd çR;sd l£ol] fiNyh l£ol dk
60 fnu ds
varjky ;k çLrkfod le;kuqlkj ;k tks Hkh igys gks djokuh pkfg,A
okjaVh dh oS/krk
pg97_103.pmd2/25/2005, 9:59 AM 100

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd2/25/2005, 10:00 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd2/25/2005, 10:00 AM 10

JOBS TO BE CARRIED OUT DURING TENTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-12
DETWHITE.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING NINTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy
operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if
necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork,
Front & Rear Wheel Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
VALIDITY
KMSDATE OF
SERVICESERVICE DEALER
STAMP
7
PAID
8
PAID12500 - 13000
14500 - 15000 PAID SERVICE RECORD
10-14
DETWHITE.pmd2/25/2005, 10:00 AM 4