wheel YAMAHA YD110 2005 Owner's Manual

The exhaust gas of an Engine pollutes air with such gases which are very dangerous for mankind. In order to ensure
clean and healthy environment, strict regulations have been enforced to control pollution. As per regulations ‘CO’
emissions by petrol driven Two Wheelers must be less than 3.5% (by volume) during Idling of the Engine.fudkl çokg fu;a=k.k ls lacf/kr rF;% batu ls ckgj fudyus okyh xSl gok d¨ mu xSl¨ ls çnwf"kr dj nsrk gS t¨ ekuo thou
ds fy, cgqr [krjukd gSA blh lanHkZ esa lkQ v©j LoLFk okrkoj.k d¨ lqfuf'pr djus ds fy, çnw"k.k fu;a=k.k gsrq l[r dkuwu¨
dk çko/kku fd;k x;k gSA bUgh dkuwu¨ ds rgr iSVª¨y ls nqifg;k okgu¨ ds batu ds [kkyh pyus dh voLFkk esa lhñv¨ñ dk çokg3.5%
ls de g¨uk pkfg,A
Non Compliance with emission standards is treated as a punishable offence.çekf.kd çokg ds vuqlkj vlg;¨x djus d¨ n.MkRed vijk/k dh rjg ekuk tkrk gSAAs a Manufacture, YAMAHA MOTOR INDIA PVT. LTD. ensure that your Vehicle meets the exhaust emission
standards before leaving the Factory.,d fuekZrk ds :i esa ;kekgk e¨Vj bafM;k fyfeVsM ;g lqfuf'pr djrk gS fd vkidh e¨VjlkbZfdy QSDVªh ls ckgj vkus ls igys
fudkl çokg dh çekf.kdrkv¨a d¨ gj rjg ls iwjk djrk gSAPlease note that when new, the Vehicle has a Factory tuned Carburetor, where the Air Screw is optimally adjusted to
meet the requirement of exhaust emission. This screw must not be tampered with as it may cause variation in pre-
controlled ‘CO’ emission levels. Subsequently, it becomes very important that it should always be within the recom-
mended limit, when checked by a properly calibrated ‘CO’ Measuring Equipment.ÑI;k /;ku j[ksa] u;h g¨usa ds dkj.k e¨VjlkbZfdy esa QSDVªh esa gh lSV x;k dkc¨ZjsVj yxk g¨rk gS] tgk¡ bls ,DtkWLV ¼fudkl½&çokg
ds eqrkfod dk;kZuqlkj ,MtLV fd;k tkrk gSA dkc¨ZjsVj ds lkFk fdlh rjg dh NsM+&NkM+ ugh dh tkuh pkfg,] D;¨fd ,slk
djus ls iwoZ&fu;a=k.k dkcZu&e¨u¨vkWDlkbM ds çokg ds Lrj¨a esa fHkérk vk ldrh gSA lkFk gh] ;g cgqr vko';d g¨ tkrk gS
fd tc bls lgh rjhds ls dSyhcjsV ¼iM+rky½ fd, x, dkcZu&e¨u¨vkWDlkbM eki&midj.k ls tk¡pk tk, vkSj ;g ges'kk çLrkfod
lhek ds vUnj gh g¨uk pkfg,AFACTS RELATED WITH EXHAUST EMISSION CONTROL
9.2
çokg&fu;a=k.k ls lacf/kr rF;
pg56_96.pmd2/25/2005, 9:59 AM 95

SAFETY NORMS
9.4
lqj{kk&flðk¡r
Certain Safety norms have been mandated for the Two Wheelers to prevent accidents. The following items have
been provided in the Vehicle for your safety.lqj{kk flðkar
CMVR
fu;e¨a ds vuqlkj] n¨ ifg;k okgu¨ d¨ nq?kZVuk ls cpkus ds fy, fuf'pr lqj{kk flðkar cuk, x, gSA vkidh
lqj{kk ds fy, e¨VjlkbZfdy esa fuEufyf[kr oLrq,¡ çnku dh xbZ gSA
It is recommended to use Saree Guard, when driving with female as a pillion rider.fiNyh lokjh ds :i esa ,d efgyk ds lkFk *Mªkb¯ox^ djrs gq, ;g çLrkfor fd;k x;k gS fd e¨VjlkbZdy esa *lkM+h xkMZ^ yxk;k
tk,AIn the interest of your own safety you are requested to always keep the above items (and the Vehicle in general) in
good working condition to avoid any Accident.vkidh lqj{kk ds fgr esa vkils çkFkZuk gS fd mij¨Dr oLrqv¨a d¨ fdlh Hkh nq?kZVuk ls cpkus ds fy, vPNh dk;Z&fLFkfr esa j[ksaA1. Horn
gkuZA
2. Rear View Mirror
ihNs ns[kus ds fy, 'kh'kkA
3. Efficient Front & Brakes (To be applied simultaneously)
vxyh o fiNyh czsds ¼t¨ lkFk&lkFk yxkbZ tkrh gS½A
4. Grip for Pillion Rider
ihNs cSBs gq, O;fDr ds fy, fxziA
5. Head Light/Tail Light
gSM ykbVA ihNs dh ykbVA
6. Stay for Helmet lock
gsyesV d¨ ykWd djus ds fy, *LVs^A
7. Indicators
bafMdsVj
pg97_103.pmd2/25/2005, 9:59 AM 98

WARRANTY
9.6
okjaVh
The claim for exchange or repair of part (s) shall be considered only when:ikVZl d¨ cnyus vFkok budh fjis;j djus ds Dyse ij rHkh fopkj fd;k tk,xk tc %1. Customer ensures that immediately upon discovery of the defect he
approaches the nearest YMI Authorised Dealership with the affected
Motorcycle.
The expenses if any, to bring the Motorcycle to the YMI Authorised
Dealership shall be borne by the customer.
miHkksDrk ;g vk'oklu nsrk gS fd n¨"k dk irk yxus ds rqqjUr ckn og e¨VjlkbZfdy
ds lkFk utnhd ds okbZñ,eñvkbZñ Mhyj ds ikl igq¡p tk,xkA
e¨VjlkbZfdy dks vf/kÎÑr Mhyj ds ikl ys tkus dk fdlh rjg dk [kpZ] miHkksDrk
}kjk Lo;a lgu fd;k tk,xkA
2. Customer produces the Owner’s Manual in original to enable the YMI
Dealer to verify the Motorcycle details and servicing details.
eksVjlkbZfdy v©j mldh *l£o¯lx^ dh foLr r tkudkjh nsus ds fy, miHkksDrk dks
okbZñ,eñvkbZñ Mhyj d¨ vksulZ eSuqvy dh ewy izrh çLrqr djuh gksxhA
THIS WARRANTY IS NOT APPLICABLE TO;g *okjaVh^ mu ifjfLFkfr;ksa esa vuqdwy ugh jgsaxh tSls %1. Normal maintenance operations such as Engine tune-up, Decarbonising,
Fuel System Cleaning, Wheels, Brakes and Clutch adjustments as
well as any other normal adjustment.
;g okjaVh dojst dsoy rHkh ykxw gksxk tc eksVjlkbZfdy dks vf/kÑr Mhyj
}kjk lHkh eq¶r l£ol] cksul Ýh l£ol v©j isM l£ol çLrkfod l£ol varjky
esa djokbZ xbZ gks tks fd bl iqfLrdk ds i "B
10-39 ls 10-41 esa fn;k x;k
gS rFkk dsoy okbZñ,eñvkbZñ ds vf/kÑr&ikVZl~ o ;kekY;wc dk ç;ksx fd;k x;k
gksA ÑI;k ;g lqfuf'pr djsa fd çR;sd l£ol] fiNyh l£ol dk
60 fnu ds
varjky ;k çLrkfod le;kuqlkj ;k tks Hkh igys gks djokuh pkfg,A
okjaVh dh oS/krk
pg97_103.pmd2/25/2005, 9:59 AM 100

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd2/25/2005, 10:00 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd2/25/2005, 10:00 AM 10

JOBS TO BE CARRIED OUT DURING TENTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-12
DETWHITE.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING NINTH BONUS FREE SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy
operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if
necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork,
Front & Rear Wheel Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
VALIDITY
KMSDATE OF
SERVICESERVICE DEALER
STAMP
7
PAID
8
PAID12500 - 13000
14500 - 15000 PAID SERVICE RECORD
10-14
DETWHITE.pmd2/25/2005, 10:00 AM 4