parking brake YAMAHA YFM350R-W 2009 User Guide

7-17
7
WARNING
EWB02410Use the proper gear and maintain a steady
speed when climbing a hill.
If you lose all forward speed:
Keep weight uphill.
Apply the brakes.
Lock the parking brake after you are
stopped.
If you begin rolling backwards:
Keep weight uphill.
Never apply the brake pedal while rolling
backwards. Apply the front brake.
When fully stopped, apply the brake pedal as
well, and then lock the parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described inthe Owner’s Manual.RIDING DOWNHILL
When riding your ATV downhill, shift your weight
as far to the rear and uphill side of the ATV as pos-
sible. Move back on the seat and sit with your arms
straight. Choose a low gear which will allow the en-
gine compression to do most of the braking for you.
Improper braking may cause a loss of traction.
Use caution while descending a hill with loose or
slippery surfaces. Braking ability and traction may
be adversely affected by these surfaces. Improper
braking may also cause a loss of traction.U10P60E0.book Page 17 Thursday, June 15, 2006 4:19 PM

8-4
8
7*Rear brakeCheck operation and correct if necessary.
Check fluid level and ATV for fluid leakage, and
correct if necessary.√√√√√
Replace brake pads. Whenever worn to the limit
8*Brake hosesCheck for cracks or other damage, and replace if
necessary.√√√√
Replace. Every 4 years
9*Parking bra keCheck operation and adjust if necessary.√√√√√
10*WheelsCheck runout and for damage, and replace if nec-
essary.√ √√√
11*TiresCheck tread depth and for damage, and replace if
necessary.
Check air pressure and balance, and correct if
necessary.√ √√√
12*Wheel bearingsCheck for looseness or damage, and replace if
necessary.√ √√√
13*Swingarm pivotsCheck operation and for excessive play, and re-
place bearings if necessary.
Lubricate with lithium-soap-based grease.√√√
14*Upper and lower
arm pivotsLubricate with lithium-soap-based grease.√√√
15 Drive chainCheck chain slack and adjust if necessary.
Check rear wheel alignment and correct if necess-
sary.
Clean and lubricate.√√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1200
(750)2400
(1500)2400
(1500)4800
(3000)
hours 20 75 150 150 300U10P60E0.book Page 4 Thursday, June 15, 2006 4:19 PM

8-24
8After servicing:

Make sure the brakes operate smoothly and
that the brake pedal position is correct.
Make sure the brakes do not drag.
Make sure the brakes are not spongy. All air
must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These proceduresshould be performed by a Yamaha dealer.EBU24710Adjusting the parking brake free play The parking brake free play must be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
Cable length “A” should measure 64–68 mm
(2.52–2.68 in). Adjust the parking brake free play
as follows.1. Release the parking brake by moving the
parking brake lever to the right.
2. Fully loosen the locknut and the adjusting bolt
at the rear brake caliper.
3. Loosen the locknut on the brake cable.
4. Turn the adjusting nut on the brake cable in di-
rection (a) to increase the cable length, and in
direction (b) to decrease it.
1. Locknut
2. Adjusting bolt
3. Cable length “A”
U10P60E0.book Page 24 Thursday, June 15, 2006 4:19 PM

8-25
8
NOTE:If the cable length cannot be adjusted to specifica-tion, consult a Yamaha dealer.
5. Tighten the locknut on the brake cable.
6. Turn in the adjusting bolt at the rear brake cal-
iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.CAUTION:ECB00520When tightening the locknut, hold the adjust-
ing bolt with a wrench so that it does not turntogether with the locknut.
WARNING
EWB02090Operating with improperly serviced or adjust-
ed brakes could cause the brakes to malfunc-
tion, resulting in reduced braking
performance. This could increase the chance
of a collision or accident. After adjusting the
parking brake free play, block the rear of the
ATV off the ground and spin the rear wheels.
Check to make sure there is no brake drag. If
brake drag is noticed, perform the adjustmentagain.EBU24740Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
1. Locknut
2. Adjusting nut
Tightening torque:
Locknut (rear brake caliper):
16 Nm (1.6 m·kgf, 11 ft·lbf)
U10P60E0.book Page 25 Thursday, June 15, 2006 4:19 PM

License plate light bulb, replacing ................................ 8-39
Light switch .................................................................... 4-4MMain switch .................................................................... 4-1
Model label ................................................................... 11-1NNeutral indicator light ..................................................... 4-2OOwner’s manual and tool kit ........................................... 8-1PParking ........................................................................... 6-7
Parking brake free play, adjusting ................................ 8-24
Parking brake lever ........................................................ 4-7
Parking on a slope ......................................................... 6-8
Part locations ................................................................. 3-1
Periodic maintenance and lubrication chart ................... 8-3
Pre-operation check list .................................................. 5-1RReverse indicator light .................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 1-1
Seat .............................................................................. 4-14
Shifting ........................................................................... 6-4
Shift pedal ...................................................................... 4-8
Shock absorber assemblies, adjusting the front .......... 4-14
Shock absorber assembly, adjusting the rear .............. 4-16
Spark arrester, cleaning ............................................... 8-16
Spark plug, checking ...................................................... 8-8
Specifications ............................................................... 10-1
Speed limiter .................................................................. 4-5
Speedometer .................................................................. 4-2Starter (choke) ............................................................. 4-12
Start switch ..................................................................... 4-3
Steering lock ................................................................ 4-13
Steering shaft, lubricating ............................................. 8-35
Storage ........................................................................... 9-2
Suspension, lubricating the upper and lower arm
pivots ......................................................................... 8-34
Suspension relay arm and connecting arm pivoting
points, lubricating the rear ......................................... 8-33
Swingarm pivots, lubricating ........................................ 8-32
TTail/brake light bulb, replacing ..................................... 8-38
Throttle cable free play, adjusting ................................ 8-19
Throttle lever ........................................................... 4-4, 5-4
Tire pressure, measuring ............................................... 5-5
Tires ............................................................................... 5-4
Tire wear limit ................................................................. 5-6
Troubleshooting ........................................................... 8-42
Troubleshooting chart .................................................. 8-43
Turn signal indicator light ............................................... 4-2
Turn signal light bulb, replacing ................................... 8-38
Turn signal switch .......................................................... 4-4VValve clearance ............................................................ 8-19
Vehicle identification number ....................................... 11-1WWheel bearings, checking ............................................ 8-32
Wheel, installing ........................................................... 8-41
Wheel, removing .......................................................... 8-40
U10P60E0.book Page 2 Thursday, June 15, 2006 4:19 PM