brake YAMAHA YFM700R 2006 Notices Demploi (in French)

8-8
INITIAL EVERY
month 1 3 6 6 12
ITEM ROUTINEWhichever
km 320 1200 2400 2400 4800 comes first
(mi) (200) (750) (1500) (1500) (3000)
hours 20 75 150 150 300
Air filter element9Clean. Every 20–40 hours
9Replace if necessary. (more often in wet or dusty areas)
Clutch*9Check operation.
2222
9Adjust if necessary.
9Check free play/operation/fluid leakage/
Front brake*See NOTE Page 8-10.22222
9Correct if necessary.
9Check operation/fluid leakage/
Rear brake*See NOTE Page 8-10.22222
9Correct if necessary.
Wheels*9Check balance/damage/runout.
2222
9Replace if necessary.
Wheel bearings*9Check bearing assemblies for looseness/damage.
2222
9Replace if damaged.
Rear arm pivot*9Lubricate with lithium-soap-based grease.222
Upper and lower arm
pivot and steering 9Lubricate with lithium-soap-based grease.222
shaft*
Drive chain9Check and adjust slack/alignment/clean/lube.22222
Fittings and fasteners*9Check all chassis fittings and fasteners.
22222
9Correct if necessary.
Front and rear9Check operation.
22
suspension*9Correct if necessary.
1S3-9-60 8 6/7/05 10:25 AM Page 8-8

8-10
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally
check the brake fluid level and add the fluid as required.
9On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two
years.
9Replace the brake hoses every four years, or if cracked or damaged.
1S3-9-60 8 6/7/05 10:25 AM Page 8-10

8-71
EBU10272
Front and rear brake pad inspection
Each brake pad is provided with a wear indicator
groove. The indicator grooves allow checking of
brake pad wear without disassembling the
brake. Apply the brake and inspect the wear
indicator grooves. If a brake pad is worn to the
point that the wear indicator grooves are almost
in contact with the disc plate, ask a Yamaha
dealer to replace the brake pads as a set.1Front
1Rear
1. Wear indicator groove1. Rainure d’indicateur d’usure1. Ranura indicador de desgaste
1. Wear indicator groove
1. Rainure d’indicateur d’usure1. Ranura indicador de desgaste
FrontAvantDelantero
RearArrièreTrasero
1S3-9-60 8 6/7/05 10:25 AM Page 8-71

8-73
EBU15820
Brake fluid level inspection
Insufficient brake fluid may let air enter the
brake system, possibly causing the brakes to
become ineffective.
Before riding, check that the brake fluid is above
the minimum level mark and replenish if neces-
sary. A low brake fluid level may indicate worn
brake pads and/or brake system leakage. If the
brake fluid level is low, be sure to check the
brake pads for wear and the brake system for
leakage.
NOTE:
To access the rear brake fluid reservoir cap,
remove the seat (see page 4-29), remove the
cowling bolt and quick fastener, and then pull
the cowling slightly outward as shown.
.
1. Minimum level mark 1. Repère de niveau minimum 1. Marca de mínimo
FrontAvantDelantero
1
Rear
1. Minimum level mark 1. Repère de niveau minimum 1. Marca de mínimo
RearArrièreTrasero
1S3-9-60 8 6/7/05 10:25 AM Page 8-73

8-75
Observe these precautions:
8When checking the brake fluid level, make
sure the top of the brake fluid reservoir is
level.
8Use only the designated quality brake fluid,
otherwise, the rubber seals may deteriorate,
causing leakage and poor brake performance.
8Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reac-
tion and lead to poor brake performance.
8Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock.
8Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
8Have a Yamaha dealer check the cause if the
brake fluid level goes down.
1
2
1. Cowling
2. Rear brake fluid reservoir cap
1. Carénage
2. Bouchon du réservoir de liquide de frein
1. Carenado
2. Tapa del depósito del líquido de los frenos traseros
Recommended brake fluid: DOT 4
1
2
1. Quick fastener 2. Bolt1. Rivets démontables 2. Boulon1. Fijadores rápidos 2. Perno
1S3-9-60 8 6/7/05 10:25 AM Page 8-75

8-77
EBU11860
Brake fluid replacement
Complete fluid replacement should be done only
by trained Yamaha service personnel. Have a
Yamaha dealer replace the following compo-
nents during periodic maintenance or when they
are damaged or leaking.
8Replace the oil seals every two years.
8Replace the brake hoses every four years.
1S3-9-60 8 6/7/05 10:25 AM Page 8-77

8-79
EBU11880
Front brake lever free play
The front brake lever should have a free play of
zero mm at the lever end. If not, have a Yamaha
dealer check the brake system.
w
Operating with improperly serviced or
adjusted brakes could cause loss of braking
ability which could lead to an accident.
After servicing:
8Make sure the brakes operate smoothly
and that the free play is correct.
8Make sure the brakes do not drag.
8Make sure the brakes are not spongy. All
air must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.
a. Brake lever free play a. Jeu du levier de freina. Juego de la palanca de freno
1S3-9-60 8 6/7/05 10:25 AM Page 8-79

8-81
EBU10790
Brake pedal height adjustment
The top of the brake pedal should be positioned
15.3 mm below the top of the footrest. If not,
have a Yamaha dealer adjust it.
w
Operating with improperly serviced or
adjusted brakes could cause loss of braking
ability, which could lead to an accident.
After servicing:
8Make sure the brakes operate smoothly
and that the brake pedal position is cor-
rect.
8Make sure the brakes do not drag.
8Make sure the brakes are not spongy. All
air must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.
a
a. Brake pedal positiona. Hauteur de la pédale de freina. Altura del pedal del freno
1S3-9-60 9-11 4/27/05 2:13 PM Page 8-81

8-83
EBU16060
Parking brake adjustment
Parking brake adjustment may be required if the
parking brake does not hold properly. The cable
length “A” should be adjusted to 58–60 mm.
1. Release the parking brake by moving the
parking brake lever to the right.
2. Loosen the locknut on the brake cable.
3. Turn the adjusting nut on the brake cable
in direction ato increase the cable length
or in direction bto decrease the cable
length.
NOTE:
If the cable cannot be adjusted to specification,
consult a Yamaha dealer.
4. Tighten the locknut on the brake cable.
A
1 2
ab
A. Cable lengthA. Longueur du câbleA. Longitud del cable
1. Locknut 2. Adjusting bolt
1. Contre-écrou 2. Boulon de réglage1. Contratuerca 2. Perno de ajuste
1S3-9-60 9-11 4/27/05 2:13 PM Page 8-83

8-85
w
Operating with improperly adjusted brakes
could cause the brakes to malfunction,
resulting in reduced braking performance.
This could increase the chance of a collision
or accident. After adjusting the parking
brake, block the rear of the machine off the
ground and spin the rear wheels. Check to
make sure there is no brake drag. If brake
drag is noticed, perform the adjustment
again.
1S3-9-60 9-11 4/27/05 2:13 PM Page 8-85