brake YAMAHA YFM80R 2003 Notices Demploi (in French)

8-47
EBU00336
Rear brake lever and pedal adjustment
1. Brake lever free play adjustment
a. Loosen the brake cable locknut.
b. Turn the adjusting bolt at the brake lever
until brake lever free play is 5–8 mm.
c. Tighten the locknut.
NOTE:
If specified free play cannot be obtained, tighten
the brake cable adjusting nut at the rear wheel
hub until brake lever free play is 5–8 mm.
wqa
q
1. Locknut 2. Adjusting bolt1. Contre-écrou 2. Boulon de réglage1. Contratuerca 2. Perno de ajustea. Free playa. Jeua. Juego
1. Rear brake lever free play adjusting nut
1. Ecrou de réglage du jeu au levier de frein1. Tuorca de ajuste del recorrido libre de la palanca de freno
5TH-9-61 8 4/17/02 4:46 PM Page 8-47

8-49
2. Brake pedal free play adjustment
a. Turn the brake rod adjusting nut at the rear
wheel hub until brake pedal free play is
20–30 mm.
w
Operating with improperly serviced or
adjusted brakes could cause loss of braking
ability, which could lead to an accident.
After servicing:
8Make sure the brakes operate smoothly
and that the free play is correct.
8Make sure the brakes do not drag.
Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.
a
q
a. Free playa. Jeua. Juego
1. Brake pedal free play adjusting nut
1. Ecrou de réglage du jeu de la pédale de frein1. Tuorca de ajuste del recorrido libre del pedal de freno
5TH-9-61 8 4/17/02 4:46 PM Page 8-49

8-55
EBU00727
Brake and shift pedal/brake lever lubrication
Lubricate the pivoting parts of each lever and
pedal.
EBU01220
Knuckle shaft and steering shaft lubrication
Lubricate the pivot points using a grease gun.Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
5TH-9-61 8 4/17/02 4:46 PM Page 8-55

9-3
3. Rinse the dirt and degreaser off with a gar-
den hose. Use only enough pressure to do
the job.
cC
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high pressure deter-
gent applications such as those available in
coin-operated car washers.
4. Once the majority of the dirt has been
hosed off, wash all surfaces with warm
water and mild, detergent-type soap. An
old toothbrush or bottle brush is handy for
hard-to-get-at places.
5. Rinse the machine off immediately with
clean water and dry all surfaces with a
chamois, clean towel or soft absorbent
cloth.
5TH-9-61 9~ 4/17/02 4:45 PM Page 300

9-5
6. Clean the seat with a vinyl upholstery
cleaner to keep the cover pliable and
glossy.
7. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or pro-
tective finish.
When finished, start the engine and let it
idle for several minutes.
w
Wet brakes may have reduced stopping abili-
ty, increasing the chance of an accident.
Test the brakes after washing. Apply the
brakes several times at slow speeds to let
friction dry out the linings.
5TH-9-61 9~ 4/17/02 4:45 PM Page 302

10-5
Model YFM80W
Brake:
Front brake type Drum brake
Operation Right hand operation
Rear brake type Drum brake
Operation Left hand and right foot operation
Suspension:
Front Leading arm
Rear Swingarm
Shock absorber:
Front Coil spring/Oil damper
Rear Coil spring/Oil damper
Wheel travel:
Front wheel travel 57 mm
Rear wheel travel 56 mm
Electrical:
Ignition system C.D.I.
Charging system A.C. magneto
Battery type/voltage, capacity 12N7D-3B/12V, 7Ah
Indicator light voltage, wattage ×quantity:
Neutral 12V, 1.7W ×1
Fuse: 5A
5TH-9-61 9~ 4/17/02 4:45 PM Page 312