recommended oil YAMAHA YS125 2017 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2017, Model line: YS125, Model: YAMAHA YS125 2017Pages: 90, PDF Size: 2.24 MB
Page 30 of 90

For your safety – pre-operation checks
4-1
4
EAU15599
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
WARNING
EWA11152
Failure to inspect or maintain the vehicle properly increases the possibility of an acci dent or equipment damag e.
Do not operate the vehicle if you fin d any pro blem. If a pro blem cannot be corrected b y the proce dures provi ded in
this manual, have the vehicle inspecte d b y a Yamaha dealer.Before using this vehicle, check the following points:
ITEM CHECKS PAGE
Fuel • Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage. 3-8
En gine oil • Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage. 6-11
Front brake • Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add specified brake fluid to specified level.
• Check hydraulic system for leakage. 6-22, 6-22
Rear brake • Check operation.
• Check pedal free play.
• Adjust if necessary. 6-21, 6-22
Clutch • Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary. 6-19
UBT4E0E0.book Page 1 Thursday, November 17, 2016 10:55 AM
Page 47 of 90
![YAMAHA YS125 2017 Owners Manual Periodic maintenance an d a djustment
6-12
6
ficiently
before removin g the oil
filler cap.
[EWA17640]
NOTICE: Do not
operate the vehicle until you
know that the en gine oil level is
sufficient.
YAMAHA YS125 2017 Owners Manual Periodic maintenance an d a djustment
6-12
6
ficiently
before removin g the oil
filler cap.
[EWA17640]
NOTICE: Do not
operate the vehicle until you
know that the en gine oil level is
sufficient.](/img/51/53875/w960_53875-46.png)
Periodic maintenance an d a djustment
6-12
6
ficiently
before removin g the oil
filler cap.
[EWA17640]
NOTICE: Do not
operate the vehicle until you
know that the en gine oil level is
sufficient.
[ECA10012]
TIPThe engine oil should be between the
minimum and maximum level marks.4. If the engine oil is below the mini- mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Check the O-ring for damage, and replace it if necessary.
6. Install and tighten the engine oil filler cap.
To chan ge the en gine oil (with or
without oil filter element replace-
ment) 1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
3. Remove the engine oil filler cap, the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.
TIPSkip steps 4–6 if the oil filter element is
not being replaced.4. Remove the oil filter element coverby removing the bolts.
1. Engine oil filler cap
1. O-ring
2. Engine oil dipstick
3. Maximum level mark
4. Minimum level mark
1
4 321
1. Engine oil drain bolt
2. Gasket
1. Bolt
2. Oil filter element cover
12
1
2
UBT4E0E0.book Page 12 Thursday, November 17, 2016 10:55 AM
Page 48 of 90

Periodic maintenance an d a djustment
6-13
6 5. Remove and replace the oil filter
element and O-ring.
6. Install the oil filter element cover by installing the bolts, then tight-
ening them to the specified
torque.
TIPMake sure that the O-ring is properly
seated.7. Install the engine oil drain bolt andits new gasket, and then tighten
the bolt to the specified torque. 8. Refill with the specified amount of
the recommended engine oil.
NOTICE
ECA11621
In or der to prevent clutch slip-
pa ge (since the en gine oil also
lu bricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a hi gh-
er quality than specifie d. In
a ddition, do not use oils la beled
“ENERGY CONSERVING II” or
hi gher.
Make sure that no forei gn mate-
rial enters the crankcase.
9. Check the O-ring for damage, and replace it if necessary.
10. Install and tighten the engine oil filler cap.NOTICE
ECA10441
After chan gin g the en gine oil, b e
sure to check the oil pressure as de-
scri bed b elow.To check the oil pressure
1. Remove cowling A. (See page 6-8.)
2. Remove the Y.R.C.S. (Yamaha Ram-Air Cooling System) cap.
(See page 6-10.)
1. Oil filter element
2. O-ringTightenin g torque:
Oil filter element cover bolt: 10 N·m (1.0 kgf·m, 7.2 lb·ft)
2 1
Ti
ghtenin g torque:
Engine oil drain bolt:
20 N·m (2.0 kgf·m, 14 lb·ft)
Recommen ded en gine oil:
See page 8-1.
Oil quantity:
Oil change:1.00 L (1.06 US qt, 0.88 Imp.qt)
With oil filter removal:
1.10 L (1.16 US qt, 0.97 Imp.qt)
1. Engine oil filler cap
2. O-ring
21
UBT4E0E0.book Page 13 Thursday, November 17, 2016 10:55 AM
Page 81 of 90

Specifications
8-1
8
Dimensions:Overall length:2005 mm (78.9 in)
Overall width:
735 mm (28.9 in)
Overall height: 1050 mm (41.3 in)
Seat height: 795 mm (31.3 in)
Wheelbase:
1320 mm (52.0 in)
Ground clearance: 150 mm (5.91 in)
Minimum turning radius: 2.2 m (7.22 ft)Wei ght:Curb weight:
129 kg (284 lb)Engine:Combustion cycle:
4-stroke
Cooling system: Air cooled
Valve train: SOHC
Number of cylinders:
Single cylinder
Displacement: 125 cm³
Bore × stroke:
52.4 × 57.9 mm (2.06 × 2.28 in)
Compression ratio:
10.0 : 1 Starting system:
Electric starter
Lubrication system: Wet sump
Engine oil:Recommended brand:
YAMALUBE
SAE viscosity grades: 10W-40, 20W-40
Recommended engine oil grade: API service SG type or higher, JASO
standard MA
Engine oil quantity:
Oil change:1.00 L (1.06 US qt, 0.88 Imp.qt)
With oil filter removal:
1.10 L (1.16 US qt, 0.97 Imp.qt)Air filter:Air filter element:Dry element
Fuel:Recommended fuel:Regular unleaded gasoline (Gasohol [E10]
acceptable)
Fuel tank capacity: 14 L (3.7 US gal, 3.1 Imp.gal)
Fuel reserve amount:
2.2 L (0.58 US gal, 0.48 Imp.gal)Fuel injection:Throttle body:ID mark:BT41 00Spark plu g(s):Manufacturer/model:
NGK/CPR8EA-9
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:
Wet, multiple-discDrivetrain:Primary reduction ratio:3.409 (75/22)
Final drive:
Chain
Secondary reduction ratio: 3.071 (43/14)
Transmission type: Constant mesh 5-speed
Gear ratio:
1st:2.714 (38/14)
2nd:
1.789 (34/19)
010305070 90110
130 ˚F
-20 -10 0 10 20 3040
50 ˚C
SAE 10W-40
SAE 20W-40
UBT4E0E0.book Page 1 Thursday, November 17, 2016 10:55 AM