oil YAMAHA YXZ1000R SS 2017 Owner's Guide

8-47
8
Be careful that water or dust does not
enter the brake or clutch fluid reservoir
when refilling. Water will significantly
lower the boiling point of the fluid and
may result in vapor lock. NOTICEECB01161Brake fluid may damage painted surfaces
or plastic parts. Always clean up spilled
fluid immediately. As the brake pads wear, it is normal for the
brake fluid level to gradually go down. A low
brake fluid level may indicate worn brake
pads or brake system l eakage; therefore, be
sure to check the brake pads for wear and the
brake system for leakage. A low clutch fluid
level may indicate clutch system leakage;
therefore, be sure to check the clutch system
for leakage. If the brake or clutch fluid level
goes down suddenly, have a Yamaha dealer
check and repair the vehicle before any fur-
ther operation.
EBU35170Brake and clutch fluid replacementComplete fluid replacement should be done
only by trained Yamaha service personnel.
Have a Yamaha dealer replace the following
components during periodic maintenance or
when they are damaged or leaking.
 Replace the oil seals every two years.
 Replace the brake and clutch hoses every
four years.EBU35181Checking the clutch pedalThe clutch pedal should operate smoothly
and spring back to position when released.
When depressed, it should offer resistance
before reaching the floorboard. If the pedal
offers little resistance when depressed, or if
the transmission grinds gears when shifting,
have a Yamaha dealer check the vehicle.
U2HC7ME0.book Page 47 Tuesday, April 19, 2016 10:33 AM

8-57
8
EBU35230BatteryThe battery is located under panel A. (See
page 8-10.)
This model is equipped with a VRLA (Valve
Regulated Lead Acid) battery. There is no
need to check the electrolyte or to add dis-
tilled water. However, the battery lead con-
nections need to be checked and, if
necessary, tightened.
WARNING
EWB03410Avoid battery contact with skin, eyes, or
clothing. Shield eyes when working near
batteries. Keep out of reach of children.
You could be poisoned or severely burnedby the sulfuric acid in battery electrolyte. In
case of accidental contact with battery
electrolyte:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water
or milk. Follow with milk of magnesia,
beaten egg, or vegetable oil. Get prompt
medical attention.
EYES: Flush with water for 15 minutes and
get prompt medical attention.

WARNING
EWB03420Batteries may produce explosive gases.
Ventilate when charging or using in a
closed space. Keep batteries away from
sparks, flames, cigarettes, or other sourc-
es of ignition. To remove the battery
1. Turn the key to “ ” (off).
2. Remove panel A. (See page 8-10.)
Tightening torques: Front wheel nut:75 N·m (7.5 kgf·m, 54 lb·ft)
Rear wheel nut: 75 N·m (7.5 kgf·m, 54 lb·ft)
U2HC7ME0.book Page 57 Tuesday, April 19, 2016 10:33 AM

9-2
9
7. Automotive-type wax may be applied toall painted and chrome-plated surfaces.
Avoid combination cleaner-waxes. Many
contain abrasives which may scratch the
paint or protective finish. When finished,
start the engine and let it idle for several
minutes.EBU32741StorageLong term storage (60 days or more) of your
vehicle will require some preventive proce-
dures to guard against deterioration. Make
any necessary repairs before storing the vehi-
cle.
After thoroughly cleaning the vehicle, prepare
for storage as follows:
1. Fill the fuel tank with fresh fuel and add the specified amount of Fuel Med Rx or
another high-quality fuel stabilizer prod-
uct. Follow the instructions on the prod- uct label. Operate the vehicle for at least
5 minutes to distribute treated fuel
through the fuel system.
2. Remove the spark plugs and pour one ta- blespoon of fresh engine oil into each cyl-
inder and then re-install the spark plugs.
Remove the spark plug wires and ground
them. Operate the electric starter to turn
the engine over several times and coat
the cylinder walls with oil.
3. Lubricate all control cables.
4. Put the frame on stands or blocks to raise all wheels off the ground.
5. Tie a plastic bag over the exhaust pipe outlet to prevent moisture from entering.
Specified amount:1 oz of stabilizer to each gallon of fuel (or
7.5 ml of stabilizer to each liter of fuel)
U2HC7ME0.book Page 2 Tuesday, April 19, 2016 10:33 AM

9-3
9
6. If storing in a humid or salt-air atmo-sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat covers.
7. Remove the battery and charge it. Store
it in a dry place and recharge it once a
month. Do not store the battery in an ex-
cessively warm or cold place [less than 0
°C (30 °F) or more than 30 °C (90 °F)].
Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha
dealer if the fuel system needs to be drained.U2HC7ME0.book Page 3 Tuesday, April 19, 2016 10:33 AM

10-1
10
EBU32750
SPECIFICATIONS
Dimensions:Overall length:3121 mm (122.9 in)
Overall width: 1626 mm (64.0 in)
Overall height:
1834 mm (72.2 in)
Wheelbase: 2300 mm (90.6 in)
Ground clearance: 330 mm (13.0 in)
Minimum turning radius:
6000 mm (236 in)Weight:Curb weight:685.0 kg (1510 lb) (YXZ10YMXH)
708.0 kg (1561 lb) (YXZ10YMSH)Noise and vibration level:Noise level (77/311/EEC):
85.8 dB(A) at 4125 r/min (YXZ10YMSH,
YXZ10YMXH_EUR/FRA/GBR)
Uncertainty of measurement:
3.0 dB(A) (YXZ10YMSH, YXZ10YMXH_EUR/FRA/GBR)
A-weighted sound power level: 100.0 dB(A) at 4125 r/min (YXZ10YMSH,
YXZ10YMXH_EUR/FRA/GBR)
Uncertainty of measurement: 3.0 dB(A) (YXZ10YMSH, YXZ10YMXH_EUR/FRA/GBR) Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s² (YXZ10YMSH,
YXZ10YMXH_EUR/FRA/GBR)
Uncertainty of measurement:
0.0 m/s² (YXZ10YMSH, YXZ10YMXH_EUR/FRA/GBR)
Vibration on handle (EN1032, ISO5008): Will not exceed 2.5 m/s² (YXZ10YMSH,
YXZ10YMXH_EUR/FRA/GBR)
Uncertainty of measurement: 0.2 m/s² (YXZ10YMSH, YXZ10YMXH_EUR/FRA/GBR)
Engine:Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement: Inline 3-cylinder
Displacement: 998 cm³
Bore × stroke:
80.0 × 66.2 mm (3.15 × 2.61 in)
Compression ratio: 11.3 : 1
Starting system: Electric starter
Lubrication system:
Dry sumpEngine oil:Recommended brand:YAMALUBE
U2HC7ME0.book Page 1 Tuesday, April 19, 2016 10:33 AM

10-2
10
Type:SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Engine oil quantity: Without oil filter cartridge replacement: 2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter cartridge replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)Transmission oil:Recommended brand:YAMALUBE
Type: SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA Quantity:
1.50 L (1.59 US qt, 1.32 Imp.qt)
Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.47 L (0.50 US qt, 0.41 Imp.qt)Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level mark):
0.31 L (0.33 US qt, 0.28 Imp.qt)
Radiator (including all routes): 3.75 L (3.96 US qt, 3.30 Imp.qt)Air filter:Air filter element:
Wet element
Secondary air filter element: Oil-coated paper elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity: 34.0 L (8.98 US gal, 7.48 Imp.gal)Fuel injection:Throttle body:
ID mark: 2HC1 00
0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
U2HC7ME0.book Page 2 Tuesday, April 19, 2016 10:33 AM

10-4
10
(Total weight of operator, passenger, cargo, and
accessories)Tire air pressure (measured on cold tires):Recommended:Vehicle load: 0 - 195 kg (0 - 430 lb)
Front:
114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear: 128.0 kPa (1.280 kgf/cm², 18.5 psi)
Vehicle load: 195 kg - maximum (430 lb - maximum)
Front:
114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear: 169.0 kPa (1.690 kgf/cm², 24.5 psi)
Minimum: Vehicle load: 0 - 195 kg (0 - 430 lb)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear:
124.0 kPa (1.240 kgf/cm², 18.0 psi)
Vehicle load: 195 kg - maximum (430 lb - maximum)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear:
165.0 kPa (1.650 kgf/cm², 24.0 psi)Front wheel:Wheel type:Cast wheel Rim size:
14 x 6.5AT
Rear wheel:Wheel type:
Cast wheel
Rim size: 14 x 8.0ATFront brake:Type:
Hydraulic disc brake
Specified brake fluid: DOT 4Rear brake:Type:
Hydraulic disc brake
Specified brake fluid: DOT 4Front suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel: 410 mm (16.2 in)Rear suspension:Type:Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel:
432 mm (17.0 in)
U2HC7ME0.book Page 4 Tuesday, April 19, 2016 10:33 AM

12-1
12
INDEX
AAccelerator pedal ......................................................... 4-18
Accelerator pedal, checking ........................................ 8-49
Accelerator pedal, Pre-operation check ........................ 5-7
Air filter ......................................................................... 8-37
Air filter case hoses, cleaning ...................................... 8-41
Auxiliary DC jack .......................................................... 4-46
Axle boots .................................................................... 8-35BBasic guide for safe use ................................................ 7-1
Battery, Periodic maintenance .................................... 8-57
Bead lock, checking and tightening (YXZ10YMSH) .... 8-55
Brake and clutch fluid levels, checking ....................... 8-45
Brake fluid, replacing ................................................... 8-47
Brake light switch, adjusting ........................................ 8-50
Brake pedal .................................................................. 4-19
Brake pedal, checking ................................................. 8-48
Brakes, Periodic maintenance ..................................... 8-44
Brakes, Pre-operation check ......................................... 5-3CCable, inspecting and lubrication ................................ 8-51
Cargo bed .................................................................... 4-29
Cleaning ......................................................................... 9-1
Clutch pedal ................................................................. 4-19
Clutch pedal, checking ................................................ 8-47
Clutch, Pre-operation check .......................................... 5-3
Control cables, Pre-operation check ............................. 5-8
Coolant, Periodic maintenance ................................... 8-33
Coolant, Pre-operation check ........................................ 5-6Coolant temperature warning light ................................ 4-4
Cup holders ................................................................. 4-28
DDifferential gear lock indicator light ............................... 4-3
Differential gear oil, Periodic maintenance .................. 8-31
Differential gear, Pre-operation check ........................... 5-7
Doors ........................................................................... 4-22
Drive mode, selecting .................................................... 6-7
Driver seat position ...................................................... 4-24
Drive shaft universal joint, lubrication .......................... 8-53
Drivetrain icon ................................................................ 4-3EEngine break-in .............................................................. 6-1
Engine oil and oil filter, Periodic maintenance ............. 8-15
Engine oil, Pre-operation check .................................... 5-5
Engine trouble warning light .......................................... 4-5
EPS warning light .......................................................... 4-5FFinal gear oil, Periodic maintenance ............................ 8-29
Final gear, Pre-operation check .................................... 5-6
Fittings and fasteners, Pre-operation check ................. 5-8
Flag pole bracket ......................................................... 4-30
Front and rear brake pads, checking .......................... 8-44
Fuel, Pre-operation check ............................................. 5-4
Fuel tank cap ............................................................... 4-21
Fuse, replacing ............................................................ 8-61GGlove compartment ..................................................... 4-25HHeadlight beam, adjusting ........................................... 8-64
Headlights .................................................................... 8-63
U2HC7ME0.book Page 1 Tuesday, April 19, 2016 10:33 AM

12-3
12
Tires, Pre-operation check ............................................ 5-8
Transmission oil ........................................................... 8-26
Transmission, Pre-operation check ............................... 5-6
Troubleshooting ........................................................... 8-64
Troubleshooting charts ................................................ 8-66UUpper and lower arm pivot, lubrication ....................... 8-52VValve clearance ............................................................ 8-44
Vehicle identification number ...................................... 11-1WWheel installation ......................................................... 8-56
Wheel removal ............................................................. 8-54
U2HC7ME0.book Page 3 Tuesday, April 19, 2016 10:33 AM