gas type YAMAHA YXZ1000R SS 2017 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2017, Model line: YXZ1000R SS, Model: YAMAHA YXZ1000R SS 2017Pages: 208, PDF Size: 4.79 MB
Page 153 of 208
8-27
8
TIPThe transmission oil level should be between
the tip of the dipstick and the maximum level
mark. 4. If the oil level is at or below the tip of thedipstick, add sufficient oil of the recom-
mended type to raise it to the correct lev-
el. 5. Check the O-ring for damage, and re-
place it if necessary.
6. Install the transmission oil filler cap.
7. Install the panel.
To change the transmission oil 1. Park the vehicle on a level surface.
2. Remove panel B (page 8-10).
3. Place an oil pan under the transmission case to collect the used oil.
4. Remove the transmission oil filler cap, and then the transmission oil drain bolt
and its gasket to drain the oil from the
transmission case.1. Transmission oil filler cap
2. O-ring
3. Dipstick
4. Maximum level mark
5. Tip of the dipstick
1 3
245
U2HC7ME0.book Page 27 Tuesday, April 19, 2016 10:33 AM
Page 155 of 208
8-29
8
8. Start the engine and drive the vehicle fora few minutes to circulate the transmis-
sion oil.
9. Park the vehicle on a level surface, stop the engine, and then check the transmis-
sion case for oil leakage.TIPIf oil is leaking confirm that the transmission
oil filler cap is properly installed and then have
a Yamaha dealer check the transmission. 10. Check the transmission oil level and cor- rect if necessary.
11. Install the panel.EBU36050Final gear oilCheck the oil level and change the final gear
oil at the intervals specified in the general
maintenance and lubrication chart.
Checking the final gear oil level 1. Park the vehicle on a level surface. 2. Remove the final gear oil filler bolt and its
gasket, and then check the oil level in the
final gear case. The oil level should be at
the brim of the filler hole.
3. If the oil is below the brim of the filler hole, add sufficient oil of the recommended
type to raise it to the correct level.
NOTICE: Be sure no foreign material
enters the final gear case.
[ECB00422]
1. Final gear oil
2. Gasket
3. Final gear oil filler bolt
4. Correct oil level
24
3
1
U2HC7ME0.book Page 29 Tuesday, April 19, 2016 10:33 AM
Page 158 of 208
8-32
8
3. If the level is low, add sufficient oil of therecommended type to raise it to the
specified level. NOTICE: Be sure no for-
eign material enters the differential
gear case.
[ECB00412]
4. Check the gasket for damage, and re- place it if necessary.
5. Install the differential gear oil filler bolt and its gasket, and then tighten the bolt
to the specified torque. Changing the differential gear oil
1. Park the vehicle on a level surface.
2. Place an oil pan under the differential
gear case to collect the used oil.
3. Remove the differential gear oil filler bolt,
the differential gear oil drain bolt and their
gasket to drain the oil.1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil level
1
2
3
4
Tightening torque:Differential gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)1. Differential gear oil drain bolt
2. Gasket
1 2
U2HC7ME0.book Page 32 Tuesday, April 19, 2016 10:33 AM
Page 198 of 208
10-2
10
Type:SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA
Engine oil quantity: Without oil filter cartridge replacement: 2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter cartridge replacement: 2.70 L (2.85 US qt, 2.38 Imp.qt)Transmission oil:Recommended brand:YAMALUBE
Type: SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade: API service SG type or higher, JASO standard MA Quantity:
1.50 L (1.59 US qt, 1.32 Imp.qt)
Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.47 L (0.50 US qt, 0.41 Imp.qt)Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity: 0.18 L (0.19 US qt, 0.16 Imp.qt)Coolant quantity:Coolant reservoir (up to the maximum level mark):
0.31 L (0.33 US qt, 0.28 Imp.qt)
Radiator (including all routes): 3.75 L (3.96 US qt, 3.30 Imp.qt)Air filter:Air filter element:
Wet element
Secondary air filter element: Oil-coated paper elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity: 34.0 L (8.98 US gal, 7.48 Imp.gal)Fuel injection:Throttle body:
ID mark: 2HC1 00
0 10 30 50 70 90 110 130 F
–20 –10 0 10 20 30 40 50 CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
U2HC7ME0.book Page 2 Tuesday, April 19, 2016 10:33 AM
Page 200 of 208
10-4
10
(Total weight of operator, passenger, cargo, and
accessories)Tire air pressure (measured on cold tires):Recommended:Vehicle load: 0 - 195 kg (0 - 430 lb)
Front:
114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear: 128.0 kPa (1.280 kgf/cm², 18.5 psi)
Vehicle load: 195 kg - maximum (430 lb - maximum)
Front:
114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear: 169.0 kPa (1.690 kgf/cm², 24.5 psi)
Minimum: Vehicle load: 0 - 195 kg (0 - 430 lb)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear:
124.0 kPa (1.240 kgf/cm², 18.0 psi)
Vehicle load: 195 kg - maximum (430 lb - maximum)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear:
165.0 kPa (1.650 kgf/cm², 24.0 psi)Front wheel:Wheel type:Cast wheel Rim size:
14 x 6.5AT
Rear wheel:Wheel type:
Cast wheel
Rim size: 14 x 8.0ATFront brake:Type:
Hydraulic disc brake
Specified brake fluid: DOT 4Rear brake:Type:
Hydraulic disc brake
Specified brake fluid: DOT 4Front suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel: 410 mm (16.2 in)Rear suspension:Type:Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel:
432 mm (17.0 in)
U2HC7ME0.book Page 4 Tuesday, April 19, 2016 10:33 AM