fuel pump YAMAHA YZ125LC 2002 Owners Manual

CHAPTER 4
ENGINE
SEAT, FUEL TANK AND SIDE
COVERS.....................................................4-1
EXHAUST PIPE AND SILENCER..............4-3
RADIATOR..................................................4-4
CARBURETOR AND REED VALVE...........4-7
CYLINDER HEAD , CYLINDER AND
PISTON.....................................................4-17
CLUTCH AND PRIMARY DRIVEN
GEAR.......................................................4-30
KICK AXLE, SHIFT SHAFT AND
PRIMARY DRIVE GEAR...........................4-38
YPVS GOVERNOR...................................4-46
WATER PUMP..........................................4-49
CDI MAGNETO.........................................4-53
ENGINE REMOVAL..................................4-57
CRANKCASE AND CRANKSHAFT.........4-62
TRANSMISSION, SHIFT CAM AND
SHIFT FORK.............................................4-69
CHAPTER 5
CHASSIS
FRONT WHEEL AND REAR WHEEL........5-1
FRONT BRAKE AND REAR BRAKE.......5-10
FRONT FORK...........................................5-27
HANDLEBAR............................................5-40
STEERING................................................5-47
SWINGARM..............................................5-52
REAR SHOCK ABSORBER.....................5-59
5NY-9-30-0 5/30/01 8:11 PM Page 20

2-4
SPECMAINTENANCE SPECIFICATIONS
Item Standard Limit
Transmission:
Main axle deflection limit…
0.01 mm (0.0004 in)
Drive axle deflection limit…
0.01 mm (0.0004 in)
Shifter:
Shifting type Cam drum and guide bar…
Guide bar bending limit…
0.05 mm (0.0020 in)
Kick starter type: Kick and mesh type…
Kick clip friction force P=0.8~1.2 kg (1.8~2.6 lb)…
Air filter oil grade (oiled filter):Foam-air-filter oil or engine mixing oil…
Carburetor: USA, CDN, ZA
EUROPE
AUS, NZ
Type/Manufacturer TMXχ
38SS←
/MIKUNI
I.D. mark 5NY1 00 5NY2 10…
Main jet (M.J.) #420 #430…
Jet needle-clip position (J.N.) 6CHY5-79-3 6CHY5-77-3…
Cutaway (C.A.) 5.75←…
Pilot jet (P.J.) #30←…
Pilot air screw (P.A.S.) 2-1/2 1-3/4…
Valve seat size (V.S.)
ø3.8 mm (0.15 in)←…
Starter jet (G.S.) #80←…
Fuel level (F.L.) 9.5~10.5 mm 11.5~12.5 mm
(0.37~0.41 in) (0.45~0.49 in)
Reed valve:
Thickness* 0.42 mm (0.017 in)…
Valve stopper height 8.2~8.6 mm (0.323~0.339 in)…
Valve bending limit…
0.2 mm (0.008 in)
Cooling:
Radiator core size:
Width 107.8 mm (4.24 in)…
Height (left) 240 mm (9.45 in)…
(right) 220 mm (8.66 in)…
Thickness 32 mm (1.26 in)…
Radiator cap opening pressure 95~125 kPa…
(0.95~1.25 kg/cm
2, 13.5~17.8 psi)
Radiator capacity (total) 0.57 L (0.50 Imp qt, 0.60 US qt)…
Water pump:
Type Single-suction centrifugal pump…
5NY-9-30-2A 5/24/01 8:03 PM Page 5

4-57
ENGENGINE REMOVAL
Extent of removal Order Part name Q’ty Remarks
ENGINE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Seat and fuel tankRefer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
Carburetor Refer to “CARBURETOR AND REED
VALVE” section.
Exhaust pipe and silencer Refer to “EXHAUST PIPE AND
SILENCER” section.
Clutch cable Disconnect at engine side.
Radiator hose 2 Disconnect at cylinder head side.
Radiator hose 4 Disconnect at water pump side.
Bolt (radiator) Refer to “RADIATOR” section.
Radiator hose 3 Disconnect at right side radiator,
then shift the radiators forward.
Spark plug cap
Disconnect the CDI magneto lead.
EC4M0000
ENGINE REMOVAL
w
Support the machine securely so there is no dan-
ger of it falling over.
26 Nm (2.6 m•kg, 19 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
60 Nm (6.0 m•kg, 43 ft•lb)
5 Nm (0.5 m•kg, 3.6 ft•lb)
5NY-9-30-4D 5/24/01 8:33 PM Page 2