stop YAMAHA YZ125LC 2004 Betriebsanleitungen (in German)

4-41
ENG
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE
GEAR
EC4B4300
Kick gear clip
1. Measure:
9Kick clip friction force
Out of specification Replace.
Use a spring gauge 1.
EC4B4400
Shift shaft
1. Inspect:
9Shift shaft 1
Bend/Damage Replace.
9Spring 2
Broken Replace.
EC4C4100
Shift guide and shift lever assembly
1. Inspect:
9Shift guide 1
9Shift lever 2
9Pawl 3
9Pawl pin 4
9Spring 5
Wear/Damage Replace.
EC4E4100
Stopper lever
1. Inspect:
9Stopper lever 1
Wear/Damage Replace.
9Bearing 2
Rotate outer race with a finger.
Rough spot/Seizure Replace the stopper
lever.
9Torsion spring 3
Broken Replace.
EC484300
Primary drive gear and primary driven gear
1. Inspect:
9Primary drive gear 1
9Primary driven gear 2
Wear/Damage Replace.
Kick clip friction force:
0.8~1.2 kg (1.8~2.6 lb)
5XE-9-30-4C 4/16/03 10:31 AM Page 8

4-42
ENG
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE
GEAR
EC4C5000
ASSEMBLY AND INSTALLATION
EC4C5120
Stopper lever
1. Install:
9Torsion spring 1
9Stopper lever 2
9Spacer 3
9Bolt (stopper lever) 4
NOTE:
9Align the stopper lever roller with the slot on
segment.
9When installing the stopper lever, make sure
that the torsion spring is in the position as
shown.
EC4C5202
Shift guide and shift lever assembly
1. Install:
9Spring 1
9Pawl pin 2
9Pawl 3
To shift lever 4.
2. Install:
9Shift lever assembly 1
To shift guide 2.
3. Install:
9Shift lever assembly 1
9Shift guide 2
NOTE:
9The shift lever assembly is installed at the
same time as the shift guide.
9Apply the transmission oil on the bolt (seg-
ment) shaft.
10 Nm (1.0 m•kg, 7.2 ft•lb)
5XE-9-30-4C 4/16/03 10:31 AM Page 10

4-43
ENG
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE
GEAR
4. Install:
9Bolt (shift guide) 1
EC4C5301
Shift shaft
1. Install:
9Roller 1
9Shift shaft 2
NOTE:
Apply the transmission oil on the roller and shift
shaft.
EC4B5302
Kick axle assembly
1. Install:
9Kick gear 1
9Plain washer 2
9Torsion spring 3
To kick axle 4.
NOTE:
Make sure the stopper aof the torsion spring
fits into the hole bon the kick axle.
2. Install:
9Spring guide 1
NOTE:
Slide the spring guide into the kick axle, make
sure the groove ain the spring guide fits on the
stopper of the torsion spring.
3. Install:
9Kick axle assembly 1
NOTE:
9Apply the transmission oil on the kick axle.
9Slide the kick axle assembly into the
crankcase, make sure the clip 2and kick axle
stopper afit into their home positions b, c.
10 Nm (1.0 m•kg, 7.2 ft•lb)
5XE-9-30-4C 4/16/03 10:31 AM Page 12

4-60
ENGENGINE REMOVAL
EC4M5000
ASSEMBLY AND INSTALLATION
EC4M5171
Engine installation
1. Install:
9Engine 1
Install the engine from right side.
9Pivot shaft 2
9Engine mounting bolt (lower) 3
9Engine mounting bolt (front) 4
9Engine bracket 5
9Bolt (engine bracket) 6
9CDI unit bracket 7
9Engine mounting bolt (upper) 8
NOTE:
Apply the molybdenum disulfide grease on the
pivot shaft.
EC4M5211
Brake pedal
1. Install:
9Spring 1
9Brake pedal 2
9O-ring 3
9Bolt (brake pedal) 4
9Clip 5
NOTE:
9Apply the lithium soap base grease on the bolt,
O-rings and brake pedal bracket.
9Install the clip with its stopper portion afacing
inward.
EC4M5311
Drive sprocket
1. Install:
9Drive sprocket 1
9Drive chain 2
NOTE:
Install the drive sprocket together with the drive
chain.
85 Nm (8.5 m•kg, 61 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
26 Nm (2.6 m•kg, 19 ft•lb)
5XE-9-30-4D 3/24/03 11:14 PM Page 8

4-62
ENGCRANKCASE AND CRANKSHAFT
Extent of removal Order Part name Q’ty Remarks
CRANKCASE AND CRANKSHAFT
REMOVAL
Preparation for Engine Refer to “ENGINE REMOVAL”section.
removal Piston Refer to “
CYLINDER HEAD, CYLINDER
AND PISTON
” section.
Primary drive gear
Kick idle gearRefer to “
KICK AXLE, SHIFT SHAFT AND
Stopper leverPRIMARY DRIVE GEAR”section.
Rotor and stator Refer to “CDI MAGNETO” section.
1 Segment 1 Refer to “REMOVAL POINTS”.
2 Bolt [L=50 mm (1.97 in)] 4
3 Bolt [L=60 mm (2.36 in)] 6
4 Bolt [L=70 mm (2.76 in)] 2
5 Holder 1
6 Crankcase (right) 1 Use special tool.
7 Crankcase (left) 1 Refer to “REMOVAL POINTS”.
8 Crankshaft 1 Use special tool.
Refer to “REMOVAL POINTS”.
9 Oil seal 2
10 Bearing 2 Refer to “REMOVAL POINTS”.





EC4N0000
CRANKCASE AND CRANKSHAFT
12
3
Extent of removal:1Crankcase separation2Crankshaft removal
3Crankshaft bearing removal



30 Nm (3.0 m•kg, 22 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
20 Nm (2.0 m•kg, 14 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
5XE-9-30-4D 3/24/03 11:14 PM Page 12

4-63
ENGCRANKCASE AND CRANKSHAFT
EC4N3000
REMOVAL POINTS
EC4N3100
Segment
1. Remove:
9Bolt (segment) 1
9Segment 2
NOTE:
Turn the segment counterclockwise until it stops
and loosen the bolt.
EC4N3212
Crankcase
1. Remove:
9Crankcase (right) 1
Use the crankcase separating tool 2.
NOTE:
9Make appropriate bolts 3as shown available
by yourself and attach the tool with them.
9Fully tighten the tool holding bolts, but make
sure the tool body is parallel with the case. If
necessary, one screw may be backed out
slightly to level tool body.
9As pressure is applied, alternately tap on the
front engine mounting boss and transmission
shafts.
cC
Use soft hammer to tap on the case half.
Tap only on reinforced portions of case. Do
not tap on gasket mating surface. Work
slowly and carefully. Make sure the case
halves separate evenly. If one end “hangs
up”, take pressure off the push screw, re-
align, and start over. If the cases do not
separate, check for a remaining case
screw or fitting. Do not force.
Crankcase separating tool:
YU-1135-A/90890-01135
5XE-9-30-4D 3/24/03 11:14 PM Page 14

4-68
ENGCRANKCASE AND CRANKSHAFT
6. Install:
9Holder 1
9Bolt (holder) 2
7. Install:
9Segment 1
9Bolt (segment) 2
NOTE:
9When installing the segment onto the shift cam
3, align the punch mark awith the dowel pin
b.
9Turn the segment clockwise until it stops and
tighten the bolt.
8. Remove:
9Sealant
Forced out on the cylinder mating surface.
9. Apply:
9Engine oil
To the crank pin, bearing, oil delivery hole
and connecting rod big end washer.
10. Check:
9Crankshaft and transmission operation
Unsmooth operation Repair.
30 Nm (3.0 m•kg, 22 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
5XE-9-30-4D 3/24/03 11:14 PM Page 24

3. Install:
9Spring 1
9Brake pedal 2
9O-ring 3
9Bolt (brake pedal) 4
9Clip 5
NOTE:
9Apply the lithium soap base grease on the
bolt, O-ring and brake pedal bracket.
9Install the clip with its stopper portion afac-
ing inward.
5-22
CHASFRONT BRAKE AND REAR BRAKE
26 Nm (2.6 m•kg, 19 ft•lb)
EC5A5911
Front brake hose
1. Install:
9Brake hose 1
To brake hose holder 2.
NOTE:
Before tightening the bolt (brake hose holder),
align the top aof the brake hose neck with the
brake hose holder bottom b. Then pass the
brake hose in front of the axle boss cand fit it
into the hose groove dso that the brake hose
does not contact the nut (wheel axle).
2. Install:
9Hose cover 1
9Plain washer 2
9Bolt [hose cover (M8)] 3
9Bolt [hose cover (M6)] 4
10 Nm (1.0 m•kg, 7.2 ft•lb)
16 Nm (1.6 m•kg, 11 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
4. Install:
9Pin 1
9Plain washer 2
9Cotter pin 3
NOTE:
After installing, check the brake pedal height.
Refer to “REAR BRAKE ADJUSTMENT” section
in the CHAPTER 3.
5XE-9-30-5A 4/28/03 6:06 PM Page 44

5-27
CHASFRONT FORK
Extent of removal Order Part name Q’ty Remarks
FRONT FORK DISASSEMBLY
1Cap bolt 1 Refer to “REMOVAL POINTS”.
2Fork spring 1 Drain the folk oil.
3Dust seal 1
4Stopper ring 1 Refer to “REMOVAL POINTS”.
5Inner tube 1
6Outer tube 1
7Piston metal 1
8Slide metal 1
9Oil seal washer 1
0Oil seal 1
qSpring guide 1
wBase valve 1 Use special tool.
eDamper rod 1 Refer to “REMOVAL POINTS”.
EC558000
FRONT FORK DISASSEMBLY
1
Extent of removal:1Oil seal removal2Damper rod removal
2






29 Nm (2.9 m•kg, 21 ft•lb)1 Nm (0.1 m•kg, 0.7 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
55 Nm (5.5 m•kg, 40 ft•lb)
5XE-9-30-5B 4/30/03 9:41 AM Page 4

5-29
CHASFRONT FORK
EC553201
Inner tube
1. Remove:
9Dust seal 1
9Stopper ring 2
Using slotted-head screwdriver.
cC
Take care not to scratch the inner tube.
2. Remove:
9Inner tube 1
EC553311
Damper rod
1. Remove:
9Base valve 1
9Damper rod 2
NOTE:
Use a damper rod holder 3to lock the
damper rod.
EC554000
INSPECTIONEC554100
Damper rod
1. Inspect:
9Damper rod 1
Bend/DamageReplace damper rod.
cC
The front fork with a built-in piston rod has
a very sophisticated internal construction
and is particularly sensitive to foreign ma-
terial.
Use enough care not to allow any foreign
material to come in when the oil is re-
placed or when the front fork is disassem-
bled and reassembled.
Oil seal removal steps:
9Push in slowly athe inner tube just be-
fore it bottoms out and then pull it back
quickly b.
9Repeat this step until the inner tube can
be pulled out from the outer tube.
Damper rod holder:
YM-01494/90890-01494
5XE-9-30-5B 4/30/03 9:41 AM Page 8