boot YAMAHA YZ125LC 2006 Manuale duso (in Italian)
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2006, Model line: YZ125LC, Model: YAMAHA YZ125LC 2006Pages: 572, PDF Dimensioni: 12.45 MB
Page 6 of 572
EC040001
IMPORTANT NOTICE
THIS MACHINE IS DESIGNED STRICTLY FOR
COMPETITION USE, ONLY ON A CLOSED
COURSE. It is illegal for this machine to be op-
erated on any public street, road, or highway.
Off-road use on public lands may also be illegal.
Please check local regulations before riding.
1. THIS MACHINE IS TO BE OPERATED
BY AN EXPERIENCED RIDER ONLY.
Do not attempt to operate this machine
at maximum power until you are totally
familiar with its characteristics.
2. THIS MACHINE IS DESIGNED TO BE
RIDDEN BY THE OPERATOR ONLY.
Do not carry passengers on this ma-
chine.
3. ALWAYS WEAR PROTECTIVE APPAR-
EL.
When operating this machine, always
wear an approved helmet with goggles
or a face shield. Also wear heavy
boots, gloves, and protective clothing.
Always wear proper fitting clothing that
will not be caught in any of the moving
parts or controls of the machine.
4. ALWAYS MAINTAIN YOUR MACHINE IN
PROPER WORKING ORDER.
For safety and reliability, the machine
must be properly maintained. Always
perform the pre-operation checks indi-
cated in this manual. Correcting a me-
chanical problem before you ride may
prevent an accident.
qSAFETY INFORMATION
1C3-9-31-0 4/28/05 4:32 PM Page 4
Page 150 of 572
3-9
INSP
ADJ
CLUTCH ADJUSTMENT
4. Inspect:
9Pressure
Impossible to maintain the specified pres-
sure for 10 seconds Repair.
9Radiator 1
9Radiator hose joint 2
Coolant leakage Repair or replace.
9Radiator hose 3
Swelling Replace.
2. Adjust:
9Clutch lever free play
EC359020
CLUTCH ADJUSTMENT
1. Check:
9Clutch lever free play a
Out of specification Adjust.
NOTE:
9Before adjustment, expose the adjuster by
moving the boot 3and cap 4away.
9Make minute adjustment on the lever side
using the adjuster 5.
9After adjustment, check proper operation of
clutch lever.
Clutch lever free play a a
:
8~13 mm (0.31~0.51 in)
Clutch lever free play adjustment steps:
9Loosen the locknut 1.
9Turn the adjuster 2until free play ais with-
in the specified limits.
9Tighten the locknut.
Locknut:
4 Nm (0.4 m•kg, 2.9 ft•lb)
3. Install:
9Cap 1
9Boot 2
NOTE:
Place the tip aof the cap in the boot.
1C3-9-31-3A 4/28/05 2:48 PM Page 26
Page 386 of 572
5-13
CHASFRONT BRAKE AND REAR BRAKE
Extent of removal Order Part name Q’ty Remarks
MASTER CYLINDER DISASSEMBLY
1Master cylinder cap 1
2Diaphragm 1
3Reservoir float 1
4Master cylinder boot 1
5Circlip 1 Use a long nose circlip pliers.
6Plain washer 1
7Push rod 1
8Master cylinder kit 1
EC5A8300
MASTER CYLINDER DISASSEMBLY
AFront
BRear
Extent of removal:1Front master cylinder disassembly2Rear master cylinder disassembly
1
12
2 Nm (0.2 m•kg, 1.4 ft•lb)
2 Nm (0.2 m•kg, 1.4 ft•lb)
2
2
1C3-9-31-5A 4/22/05 1:13 PM Page 26
Page 400 of 572
5-20
CHASFRONT BRAKE AND REAR BRAKE
4. Install:
[Front]
9Master cylinder kit 1
9Plain washer 2
9Circlip 3
9Master cylinder boot 4
To master cylinder 5.
[Rear]
9Master cylinder kit 1
9Push rod 2
9Circlip 3
9Master cylinder boot 4
To master cylinder 5.
NOTE:
9Apply the brake fluid on the master cylinder
kit.
9Apply the lithium soap base grease on the tip
of the push rod.
9When installing the circlip, use a long nose
circlip pliers.
AFront
BRear
EC5A5310
Front master cylinder
1. Install:
9Master cylinder 1
9Master cylinder bracket 2
9Bolt (master cylinder bracket) 3
NOTE:
9Install the bracket so that the arrow mark a
face upward.
9First tighten the bolts on the upper side of the
master cylinder bracket, and then tighten the
bolts on the lower side.
9 Nm (0.9 m•kg, 6.5 ft•lb)
2. Install:
9Brake lever 1
9Bolt (brake lever) 2
9Nut (brake lever) 3
NOTE:
Apply the lithium soap base grease on the
brake lever sliding surface, bolt and contacting
surface of the master cylinder piston.
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
1C3-9-31-5A 4/22/05 1:13 PM Page 40