oil type YAMAHA YZ125LC 2006 Notices Demploi (in French)

1-12
GEN
INFO
FUEL AND ENGINE MIXING OIL
EC160051
FUEL AND ENGINE MIXING OIL
Mix oil with the gas at the ratio specified below.
Always use fresh, name-brand gasoline, and mix
the oil and gas the day of the race. Do not use
premix that is more than a few hours old.
NOTE:
If knocking or pinging occurs, use a different
brand of gasoline or higher octane grade.
cC
Never mix two types of oil in the same
batch; clotting of the oil could result. If you
wish to change oil types, be sure to drain
the fuel tank and the carburetor float bowl
of old premix prior to filling with the new
type.
Fuel tank capacity:
8.0 L (1.76 Imp gal, 2.11 US gal)
Mixing oil
Recommended oil:
Yamalube “2-R”
(Yamalube racing 2-cycle oil)
Mixing ratio: 30 : 1
If unavailable, use an equivalent
type of oil.
Recommended fuel:
Premium unleaded gasoline
only with a research octane
number of 95 or higher.
1C3-9-31-1B 3/31/05 11:58 AM Page 2

2-1
SPECGENERAL SPECIFICATIONS
Model name: YZ125V (USA, CDN)
YZ125 (EUROPE, ZA)
YZ125V (AUS, NZ)
Model code number: 1C35 (USA, CDN)
1C36 (EUROPE)
1C38 (AUS, NZ, ZA)
Dimensions:USA, AUS, NZ, ZACDN EUROPE
Overall length 2,135 mm 2,139 mm←
(84.1 in) (84.2 in)
Overall width 827 mm←←
(32.6 in)
Overall height 1,315 mm 1,317 mm 1,318 mm
(51.8 in) (51.9 in) (51.9 in)
Seat height 997 mm 998 mm←
(39.3 in) (39.3 in)
Wheelbase 1,443 mm←←
(56.8 in)
Minimum ground clearance 386 mm 388 mm←
(15.2 in) (15.3 in)
Dry weight:
Without oil and fuel 86.0 kg (189.6 lb)
Engine:
Engine type Liquid cooled 2-stroke, gasoline
Cylinder arrangement Single cylinder, forward inclined
Displacement 124 cm
3(4.36 lmp oz, 4.19 US oz)
Bore ×Stroke 54 ×54.5 mm (2.126 ×2.146 in)
Compression ratio 8.6~10.7 : 1
Starting system Kick starter
Lubrication system: Premix (30 : 1)(Yamalube 2-R)
Oil type or grade (2-Cycle):
Transmission oil Yamalube 4 (10W-30) or SAE 10W-30 type SE
motor oil
Periodic oil change 0.66 L (0.58 Imp qt, 0.69 US qt)
Total amount 0.70 L (0.62 Imp qt, 0.74 US qt)
Coolant capacity (including all routes): 0.9 L (0.79 Imp qt, 0.95 US qt)
Air filter: Wet type element
Fuel:
Type Premium unleaded gasoline
only with a research octane
number of 95 or higher
Tank capacity 8.0 L (1.76 Imp gal, 2.11 US gal)
EC200000
SPECIFICATIONSEC211000
GENERAL SPECIFICATIONS
1C3-9-31-2A 4/30/05 2:37 PM Page 2

2-2
SPECGENERAL SPECIFICATIONS
Carburetor:
Type/Manufacturer TMXχ
38SS/MIKUNI
Spark plug:
Type/Manufacturer BR9EVX/NGK (resistance type)
Gap 0.6~0.7 mm (0.024~0.028 in)
Clutch type: Wet, multiple-disc
Transmission:
Primary reduction system Gear
Primary reduction ratio 64/19 (3.368)
Secondary reduction system Chain drive
Secondary reduction ratio 48/13 (3.692)
Transmission type Constant mesh, 6-speed
Operation Left foot operation
Gear ratio: 1st 31/13 (2.385)
2nd 29/15 (1.933)
3rd 27/17 (1.588)
4th 23/17 (1.353)
5th 24/20 (1.200)
6th 23/21 (1.095)
Chassis:USA, ZA, AUS, NZEUROPE,CDN
Frame type Semi double cradle←
Caster angle 25.5° 25.6°
Trail 105 mm (4.13 in) 107 mm (4.21 in)
T ire:
Type With tube
Size (front) 80/100-21 51M
Size (rear) 100/90-19 57M
T ire pressure (front and rear) 100 kPa (1.0 kgf/cm2, 15 psi)
Brake:
Front brake type Single disc brake
Operation Right hand operation
Rear brake type Single disc brake
Operation Right foot operation
Suspension:
Front suspension Telescopic fork
Rear suspension Swingarm (link type monocross suspension)
Shock absorber:
Front shock absorber Coil spring/oil damper
Rear shock absorber Coil spring/Gas, oil damper
Wheel travel:
Front wheel travel 300 mm (11.8 in)
Rear wheel travel 315 mm (12.4 in)
Electrical:
Ignition system CDI magneto
2
1C3-9-31-2A 4/30/05 2:37 PM Page 3

2-4
SPECMAINTENANCE SPECIFICATIONS
Item Standard Limit
Transmission:
Main axle deflection limit…
0.01 mm (0.0004 in)
Drive axle deflection limit…
0.01 mm (0.0004 in)
Shifter:
Shifting type Cam drum and guide bar…
Guide bar bending limit…
0.05 mm (0.0020 in)
Kick starter type: Kick and mesh type…
Kick clip friction force P=0.8~1.2 kg (1.8~2.6 lb)…
Air filter oil grade (oiled filter): Foam-air-filter oil or equivalent oil…
Carburetor: USA, CDN EUROPEAUS, NZ, ZA
Type/ManufacturerTMXχ
38SS←←
/MIKUNI
I.D. mark 1C35 30 1C36 40 1C37 50…
Main jet (M.J.) #410 #430←…
Jet needle-clip position (J.N.)
6BFY42-74-3 6BFY43-74-3←…
Cutaway (C.A.) 4.0←←…
Pilot jet (P.J.) #40 #45 #40…
Pilot air screw (P.A.S.) 2-1/4←←…
Valve seat size (V.S.) ø3.8 mm ←←…
(0.15 in)
Starter jet (G.S.) #80←←…
Fuel level (F.L.)
9.5~10.5 mm←←…
(0.37~0.41 in)
Reed valve:
Thickness* 0.47 mm (0.019 in)…
Valve stopper height 8.2~8.6 mm (0.323~0.339 in)…
Valve bending limit…
0.2 mm (0.008 in)
Cooling:
Radiator core size:
Width 107.8 mm (4.24 in)…
Height (left) 240 mm (9.45 in)…
(right) 220 mm (8.66 in)…
Thickness 32 mm (1.26 in)…
Radiator cap opening pressure 95~125 kPa…
(0.95~1.25 kg/cm
2, 13.5~17.8 psi)
Radiator capacity (total) 0.56 L (0.49 Imp qt, 0.59 US qt)…
Water pump:
Type Single-suction centrifugal pump…
1C3-9-31-2A 4/30/05 2:37 PM Page 5

2-7
SPECMAINTENANCE SPECIFICATIONS
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing…
Front suspension: USA, CDN, ZA,
EUROPE
AUS, NZ
Front fork travel
300 mm (11.8 in)←…
Fork spring free length
454 mm (17.9 in)←449 mm (17.7 in)
Spring rate, STD K=4.0 N/mm←…
(0.408 kg/mm,
22.8 lb/in)
Optional spring Yes←…
Oil capacity 527 cm
3522 cm3…
(18.6 Imp oz, (18.4 Imp oz,
17.8 US oz) 17.6 US oz)
Oil grade Suspension oil ←…
“S1”
Inner tube outer diameter 48 mm (1.89 in)←…
Front fork top end 5 mm (0.2 in)←…
Rear suspension: USA, CDN, ZA,
EUROPE
AUS, NZ
Shock absorber travel
131.5 mm (5.18 in)←…
Spring free length
Approx. 265 mm←…
(10.43 in)
Fitting length
One I.D. paint mark One I.D. paint mark
257 mm (10.12 in) 256 mm (10.08 in)…
Two I.D. paint marks Two I.D. paint marks
263 mm (10.35 in) 262 mm (10.31 in)…
Three I.D. paint marks Three I.D. paint marks
254.5 mm (10.02 in)253.5 mm (9.98 in)…

One I.D. paint mark
245.5 ~ 263.5 mm←…
(9.67 ~ 10.37 in)
Two I.D. paint marks
251.5 ~ 269.5 mm←…
(9.90 ~ 10.61 in)
Three I.D. paint marks
243.0 ~ 261.0 mm←…
(9.57 ~ 10.28 in)
Spring rate, STDK=46.0 N/mm ←…
(4.70 kg/mm,
263.2 lb/in)
Optional spring Yes←…
Enclosed gas pressure 1,000 kPa ←…
(10 kg/cm
2,
142 psi)
Swingarm:
Swingarm free play limit
End…
1.0 mm (0.04 in)
Side clearance…
0.2~0.9 mm
(0.008~0.035 in)
1C3-9-31-2A 4/30/05 2:37 PM Page 8

2-11
SPECMAINTENANCE SPECIFICATIONS
EC212300
ELECTRICAL
Part to be tightened Thread size Q’tyT ightening torqueNm m•kg ft•lb
Stator M 6 ×1.0 3 7 0.7 5.1
Rotor M12 ×1.25 1 56 5.6 40
Ignition coil M 6 ×1.0 2 7 0.7 5.1
Item Standard Limit
Ignition system:
Ignition timing (B.T.D.C.) 0.48 mm (0.019 in)…
Advancer type Electrical…
CDI:
Magneto-model (stator)/Manufacturer 1C3-10/YAMAHA…
Source coil 1 resistance (color) 720~1,080 Ωat 20°C (68°F)…
(Green/White-Black/Red)
Source coil 2 resistance (color) 44~66 Ωat 20°C (68°F)…
(Black-Green/Blue)
Pickup coil resistance (color) 248~372 Ωat 20°C (68°F)…
(White/Blue-White/Red)
CDI unit-model/Manufacturer 1C3-10/YAMAHA…
Ignition coil:
Model/Manufacturer 1C3-00/YAMAHA…
Minimum spark gap 6 mm (0.24 in)…
Primary winding resistance 0.24~0.36 Ωat 20°C (68°F)…
Secondary winding resistance 5.7~8.5kΩat 20°C (68°F)…
Spark plug cap:
Resistance 4~6 kΩat 20°C (68°F)…
1C3-9-31-2A 4/30/05 2:37 PM Page 12

2-8
SPECCARACTERISTIQUES D’ENTRETIEN
Article Standard Limite
Roue:
Type de roue avant Roue à rayons…
Type de roue arrière Roue à rayons…
Taille/matériau de jante avant 21 ×1,60/Aluminum…
Taille/matériau de jante arrière 19 ×1,85/Aluminum…
Limite de voile de jante:
Radial…
2,0 mm (0,08 in)
Latéral … 2,0 mm (0,08 in)
Chaîne de transmission:
Type/fabricant DID520DMA2 SDH/DAIDO…
Nombre de maillons 111 maillons+attache…
Flèche de la chaîne 48~58 mm (1,9~2,3 in)…
Longueur de chaîne (15 maillons)…
242,9 mm (9,563 in)
Frein à disque avant:
Dia. extérieur ×épaisseur 250 ×3,0 mm 250 ×2,5 mm
(9,84 ×0,12 in) (9,84 ×0,10 in)
Epaisseur de plaquette 4,4 mm (0,17 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 27,0 mm (1,063 in) ×2…
Type de liquide de frein DOT #4…
Frein à disque arrière:
Dia. extérieur ×épaisseur 245 ×4,0 mm 245 ×3,5 mm
(9,65 ×0,16 in) (9,65 ×0,14 in)
Limite de flèche…
0,15 mm (0,006 in)
Epaisseur de plaquette 6,4 mm (0,25 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 25,4 mm (1,000 in)…
Type de liquide de frein DOT #4…
Levier de frein & pédale de frein:
Position du levier de frein 95 mm (3,74 in)…
Hauteur de la pédale de frein Zéro mm (Zéro in)…
(hauteur au-dessus du haut du repose-pied)
Jeu de levier d’embrayage (côté levier) 8~13 mm (0,31~0,51 in)…
Jeu à la poignée d’accélération 3~5 mm (0,12~0,20 in)…
1C3-9-31-2A 4/30/05 2:37 PM Page 21

3-7
INSP
ADJ
RADIATOR CAP INSPECTION
cC
9Do not mix more than one type of ethyl-
ene glycol antifreeze containing corro-
sion inhibitors for aluminum engine.
9Do not use water containing impurities
or oil.
7. Install:
9Radiator cap
Start the engine and warm it up for a sev-
eral minutes.
8. Check:
9Coolant level
Coolant level low Add coolant.
EC355000
RADIATOR CAP INSPECTION
1. Inspect:
9Seal (radiator cap) 1
9Valve and valve seat 2
Crack/Damage Replace.
Exist fur deposits 3Clean or replace.
Handling notes of coolant:
The coolant is harmful so it should be handled
with special care.
w
9When coolant splashes to your eye.
Thoroughly wash your eye with water
and see your doctor.
9When coolant splashes to your clothes.
Quickly wash it away with water and then
with soap.
9When coolant is swallowed.
Quickly make him vomit and take him to
a doctor.
1C3-9-31-3A 4/28/05 2:48 PM Page 22

3-13
INSP
ADJ
TRANSMISSION OIL REPLACEMENT
3. Check:
9Transmission oil level
EC35K002
TRANSMISSION OIL REPLACEMENT
1. Start the engine and warm it up for several
minutes and wait for five minute.
2. Place the machine on a level place and hold
it on upright position by placing the suitable
stand under the engine.
3. Place a suitable container under the engine.
Transmission oil level checking steps:
9Remove the oil check bolt 1.
9Inspect the oil level.
NOTE:
Be sure the machine is positioned straight
up when inspecting the oil level.
w
Never attempt to remove the oil check bolt
just after high speed operation. The heat-
ed oil could spout out, causing danger.
Wait until the oil cools down.
Oil flows out Oil level is correct.
Oil does not flow out Oil level is low.
Add transmission
oil until oil flows
out.
9Inspect the gasket (oil check bolt), replace if
damaged.
9Tighten the oil check bolt.
Recommended oil:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
Oil check bolt:
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-31-3A 4/28/05 2:48 PM Page 34

3-14
INSP
ADJ
PILOT AIR SCREW ADJUSTMENT
4. Remove:
9Oil drain bolt 1
9Oil filler cap 2
Drain the transmission oil.
5. Install:
9Aluminum washer
9Oil drain bolt 1
6. Fill:
9Transmission oil
7. Check:
9Oil leakage
8. Check:
9Transmission oil level
9. Install:
9Oil filler cap 2
EC35L002
PILOT AIR SCREW ADJUSTMENT
1. Adjust:
9Pilot air screw 1
Recommended oil:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
Oil capacity
(periodic oil change):
0.66 L (0.58 Imp qt, 0.69 US qt)
Adjustment steps:
9Screw in the pilot air screw until it is lightly
seated.
9Back out by the specified number of turns.
Pilot air screw:
2-1/4 turns out
20 Nm (2.0 m•kg, 14 ft•lb)
1C3-9-31-3A 4/28/05 2:49 PM Page 36