clutch YAMAHA YZ125LC 2007 Manuale duso (in Italian)

4-33
CLUTCH AND PRIMARY DRIVEN GEARENG
EC484500
Friction plate
1. Measure:
9Friction plate thickness
Out of specification Replace friction
plate as a set.
Measure at all four points.
EC484600
Clutch plate
1. Measure:
9Clutch plate warpage
Out of specification Replace clutch plate
as a set.
Use a surface plate 1and thickness
gauge 2.
EC484700
Push lever axle
1. Inspect:
9Push lever axle 1
Wear/Damage Replace.
EC484810
Push rod
1. Inspect:
9Push rod 1 1
9Bearing 2
9Plain washer 3
9Push rod 2 4
9Ball 5
Wear/Damage/Bend Replace.
EC495000
ASSEMBLY AND INSTALLATION
EC485120
Push lever axle
1. Install:
9Push lever axle 1
NOTE:
Apply the lithium soap base grease on the oil
seal lip and push lever axle.
Friction plate thickness:
Standard
2.9~3.1 mm 2.8 mm
(0.114~0.122 in) (0.110 in)
Warp limit:
0.2 mm (0.008 in)
1C3-9-32-4B 4/6/06 2:11 PM Page 32

4-34
CLUTCH AND PRIMARY DRIVEN GEARENG
EC495230
Clutch
1. Install:
9Plain washer [D=ø 34 mm (1.34 in)] 1
9Spacer 2
9Bearing 3
9Primary driven gear 4
NOTE:
Apply the transmission oil on the bearing, spacer
and primary driven gear inner circumference.
2. Install:
9Plain washer [D=ø 34 mm (1.34 in)] 1
9Clutch boss 2
3. Install:
9Lock washer 1
9Nut (clutch boss) 2
NOTE:
Use the clutch holding tool 3, 4to hold the
clutch boss.
åFor USA and CDN
∫Except for USA and CDN
4. Bend the lock washer 1tab.
80 Nm (8.0 m•kg, 58 ft•lb)
Clutch holding tool:
YM-91042 ..............................3 3
90890-04086 ..........................4 4
å
∫
1C3-9-32-4B 4/6/06 2:11 PM Page 34

4-35
CLUTCH AND PRIMARY DRIVEN GEARENG
5. Install:
9Friction plate 1
9Clutch plate 2
NOTE:
9Install the clutch plates and friction plates alter-
nately on the clutch boss, starting with a friction
plate and ending with a friction plate.
9Apply the transmission oil on the friction plates
and clutch plates.
6. Install:
9Bearing 1
9Plain washer 2
9Circlip 3
To push rod 1 4.
NOTE:
Apply the lithium soap base grease on the bear-
ing and plain washer.
7. Install:
9Push rod 2 1
9Ball 2
9Push rod 1 3
NOTE:
Apply the transmission oil the push rod 1, 2 and
ball.
8. Install:
9Pressure plate 1
9. Install:
9Clutch spring 1
9Screw (clutch spring) 2
NOTE:
Tighten the screws in stage, using a crisscross
pattern.
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-4B 4/6/06 2:11 PM Page 36

4-36
CLUTCH AND PRIMARY DRIVEN GEARENG
10. Install:
9Doewl pin 1
9Gasket (cluch cover) 2
11. Install:
9Clutch cover 1
9Bolt (clutch cover) 2
NOTE:
Tighten the bolts in stage, using a crisscross
pattern.
12. Install:
9O-ring 1
9Clutch cable 2
NOTE:
Apply the lithium soap base grease on the O-
ring.
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-4B 4/6/06 2:11 PM Page 38

4-37
ENG
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE
GEAR
Extent of removal Order Part name Q’ty Remarks
RPIMARY DRIVE GEAR REMOVAL
Preparation for Drain the transmission oil.Refer to “TRANSMISSION OIL REPLACE-
removalMENT” section in the CHAPTER 3.
Clutch cable Disconnect at engine side.
Bolt (brake pedal) Shift the brake pedal downward.
Radiator hose 4 Disconnect at water pump side.
Bolt (push rod)
Refer to “CYLINDER HEAD, CYLINDER
AND PISTON” section.
1 Kick starter 1
2 Crankcase cover (right) 1
3 Bolt (Primary drive gear) 1 Only loosening
Refer to “REMOVAL POINTS”.
4 Primary driven gear 1 Refer to “CLUTCH AND PRIMARY
DRIVEN GEAR”section.
5 Primary drive gear 1
EC4C0000
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE GEAREC4C8000PRIMARY DRIVE GEAR
1
Extent of removal:1Primary drive gear removal
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
48 Nm (4.8 m•kg, 35 ft•lb)
1C3-9-32-4C 4/6/06 2:12 PM Page 2

4-43
ENG
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE
GEAR
4. Hook:
9Torsion spring 1
NOTE:
Turn the torsion spring clockwise and hook into
the proper hole ain the crankcase.
EC4C5402
Kick idle gear
1. Install:
9Kick idle gear 1
9Plain washer 2
9Circlip 3
NOTE:
Apply the transmission oil on the kick idle gear
inner circumference.
EC4C5503
Primary drive gear
1. Install:
9Spacer 1
9Primary drive gear 2
9Bolt 3
NOTE:
Install the primary drive gear with its depressed
side toward you.
2. Install:
9Primary driven gear
Refer to “CLUTCH AND PRIMARY DRI-
VEN GEAR” section.
3. Tighten:
9Bolt (primary drive gear) 1
NOTE:
Place an aluminum plate abetween the teeth of
the primary drive gear 2and driven gear 3.
4. Install:
9Dowel pin 1
9Gasket [crankcase cover (right)] 2
48 Nm (4.8 m•kg, 35 ft•lb)
1C3-9-32-4C 4/6/06 2:12 PM Page 14

4-56
ENGENGINE REMOVAL
Extent of removal Order Part name Q’ty Remarks
ENGINE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Seat and fuel tankRefer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
Carburetor Refer to “CARBURETOR AND REED
VALVE” section.
Exhaust pipe and silencer Refer to “EXHAUST PIPE AND
SILENCER” section.
Clutch cable Disconnect at engine side.
Radiator Refer to “RADIATOR” section.
Spark plug cap
Disconnect the CDI magneto lead.
EC4M0000
ENGINE REMOVAL
w
Support the machine securely so there is no dan-
ger of it falling over.
26 Nm (2.6 m•kg, 19 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
75 Nm (7.5 m•kg, 54 ft•lb)
5 Nm (0.5 m•kg, 3.6 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
1C3-9-32-4D 5/1/06 10:41 AM Page 2

Extent of removal Order Part name Q’ty Remarks
Preparation forHANDLEBAR REMOVAL
removal
Number plateRemove the band only.
1 Clutch cable 1 Disconnect at the lever side.
2 Clutch lever holder 1
3 “ENGINE STOP” button 1
4 Master cylinder 1 Refer to “REMOVAL POINTS”.
5 Throttle cable cap 1 Turn over the cap cover.
6 Throttle cable 1 Disconnect at the throttle side.
7 Throttle 1 Loosen the bolts.
8 Cap cover 1
9 Collar 1
10 Grip (left) 1 Refer to “REMOVAL POINTS”.
11 Handlebar holder (upper) 2
12 Handlebar 1
13 Handlebar holder (lower) 2
5-42
CHASHANDLEBAR
EC5B0000
HANDLEBAR
1
Extent of removal:1Handlebar removal
1 Nm (0.1 m•kg, 0.7 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
9 Nm (0.9 m•kg, 6.5 ft•lb)
28 Nm (2.8 m•kg, 20 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
40 Nm (4.0 m•kg, 29 ft•lb)
1C3-9-32-5C 4/14/06 12:05 PM Page 2

5-48
CHASHANDLEBAR
13. Install:
9“ENGINE STOP” button 1
9Clutch lever holder 2
9Bolt (clutch lever holder) 3
9Clamp 4
NOTE:
9The “ENGINE STOP” button, clutch lever hold-
er and clamp should be installed according to
the dimensions shown.
9Pass the “ENGINE STOP” button lead in the
middle of the clutch holder.
4 Nm (0.4 m•kg, 2.9 ft•lb)
12. Install:
9Bolt (grip cap) 1
w
9Install the grip cap so that the gaps a a
and
b b
between the bolt (grip cap) and brake
lever 2 2
are equal. If you make a mistake in
the grip cap installation position, the brake
lever may contact the grip cap, resulting in
poor brake performance.
9After tightening the bolts, check that the
throttle grip 3 3
moves smoothly. If it does
not, retighten the bolts for adjustment.
4 Nm (0.4 m•kg, 2.9 ft•lb)
11. Install:
9Master cylinder 1
9Master cylinder bracket 2
9Bolt (master cylinder bracket) 3
NOTE:
9Install the bracket so that the arrow mark a
faces upward.
9First tighten the bolt on the upper side of the
master cylinder bracket, and then tighten the bolt
on the lower side.
9 Nm (0.9 m•kg, 6.5 ft•lb)
1C3-9-32-5C 4/14/06 12:05 PM Page 14

5-49
CHASHANDLEBAR
14. Install:
9Clutch cable 1
NOTE:
Apply the lithium soap base grease on the clutch
cable end.
15. Adjust:
9Clutch lever free play
Refer to “CLUTCH ADJUSTMENT” section in
the CHAPTER 3.
1C3-9-32-5C 4/14/06 12:05 PM Page 16