engine YAMAHA YZ125LC 2007 Notices Demploi (in French)

5. GASOLINE IS HIGHLY FLAMMABLE.
Always turn off the engine while refuel-
ing. Take care to not spill any gasoline
on the engine or exhaust system.
Never refuel in the vicinity of an open
flame, or while smoking.
6. GASOLINE CAN CAUSE INJURY.
If you should swallow some gasoline,
inhale excess gasoline vapors, or allow
any gasoline to get into your eyes, con-
tact a doctor immediately. If any gaso-
line spills onto your skin or clothing,
immediately wash skin areas with soap
and water, and change your clothes.
7. ONLY OPERATE THE MACHINE IN AN
AREA WITH ADEQUATE VENTILATION.
Never start the engine or let it run for
any length of time in an enclosed area.
Exhaust fumes are poisonous. These
fumes contain carbon monoxide, which
by itself is odorless and colorless.
Carbon monoxide is a dangerous gas
which can cause unconsciousness or
can be lethal.
8. PARK THE MACHINE CAREFULLY;
TURN OFF THE ENGINE.
Always turn off the engine if you are
going to leave the machine. Do not
park the machine on a slope or soft
ground as it may fall over.
9. PROPERLY SECURE THE MACHINE
BEFORE TRANSPORTING IT.
When transporting the machine in an-
other vehicle, always be sure it is prop-
erly secured and in an upright position
and that the fuel cock is in the “OFF”
position. Otherwise, fuel may leak out
of the carburetor or fuel tank.
1C3-9-32-0 4/28/06 9:45 AM Page 6

EC080000
HOW TO USE
THIS MANUAL
EC081000
PARTICULARLY IMPORTANT IN
FORMATION
Q
The Safety Alert Symbol means ATTENTION!
BECOME ALERT! YOUR SAFETY IS IN-
VOLVED!
w
Failure to follow WARNING instructions could re-
sult in severe injury or death to the machine op-
erator, a bystander, or a person inspecting or re-
pairing the machine.
cC
A CAUTION indicates special precautions that
must be taken to avoid damage to the machine.
NOTE:
A NOTE provides key information to make pro-
cedures easier or clearer.
EC082000
FINDING THE REQUIRED PAGE
1. This manual consists of seven chapters;
“General Information”, “Specifications”,
“Regular inspection and adjustments”,
“Engine”, “Chassis”, “Electrical” and
“Tuning”.
2. The table of contents is at the beginning of
the manual. Look over the general layout of
the book before finding then required chap-
ter and item.
Bend the book at its edge, as shown, to find
the required fore edge symbol mark and go
to a page for required item and description.
1C3-9-32-0 4/28/06 9:45 AM Page 10

EC085002
ILLUSTRATED SYMBOLS
(Refer to the illustration)
Illustrated symbols 1to 7are designed as
thumb tabs to indicate the chapter’s number and
content.
1
General information
2Specifications
3Regular inspection and adjustments
4Engine
5Chassis
6Electrical
7Tuning
Illustrated symbols 8to rare used to identify
the specifications appearing in the text.
8
With engine mounted
9Special tool
0Filling fluid
qLubricant
wTightening
eSpecified value, Service limit
rResistance (Ω), Voltage (V), Electric current (A)
Illustrated symbols tto oin the exploded dia-
grams indicate grade of lubricant and location of
lubrication point.
t
Apply transmission oil
yApply engine mixing oil
uApply molybdenum disulfide oil
iApply lightweight lithium-soap base grease
oApply molybdenum disulfide grease
Illustrated symbols pto ain the exploded dia-
grams indicate where to apply a locking agent
and where to install new parts.
p
Apply locking agent (LOCTITER)
aUse new one
GEN
INFO
12
3
5
74
6
8
90
qw
er
tyu
io
pa
SPEC
INSP
ADJENG
CHASELEC
TUN
1C3-9-32-0 4/28/06 9:45 AM Page 14

EC090010
INDEX
GENERAL
INFORMATION
SPECIFICATIONS
REGULAR
INSPECTION AND
ADJUSTMENTS
ENGINE
CHASSIS
ELECTRICAL
TUNING
1C3-9-32-0 4/28/06 9:45 AM Page 16

EC0A0000
CONTENTS
CHAPTER 1
GENERAL INFORMATION
DESCRIPTION............................................1-1
MACHINE IDENTIFICATION......................1-2
IMPORTANT INFORMATION.....................1-3
CHECKING OF CONNECTION..................1-6
SPECIAL TOOLS........................................1-7
CONTROL FUNCTIONS.............................1-9
FUEL AND ENGINE MIXING OIL.............1-12
STARTING AND BREAK-IN.....................1-13
TORQUE-CHECK POINTS.......................1-16
CLEANING AND STORAGE....................1-17
CHAPTER 2
SPECIFICATIONS
GENERAL SPECIFICATIONS....................2-1
MAINTENANCE SPECIFICATIONS...........2-3
GENERAL TORQUE SPECIFICATIONS..2-12
DEFINITION OF UNITS............................2-12
CABLE ROUTING DIAGRAM...................2-13
CHAPTER 3
REGULAR INSPECTION
AND ADJUSTMENTS
MAINTENANCE INTERVALS.....................3-1
PRE-OPERATION INSPECTION AND
MAINTENANCE..........................................3-4
ENGINE.......................................................3-5
CHASSIS...................................................3-17
ELECTRICAL............................................3-39
1C3-9-32-0 4/28/06 9:45 AM Page 18

CHAPTER 4
ENGINE
SEAT, FUEL TANK AND SIDE
COVERS.....................................................4-1
EXHAUST PIPE AND SILENCER..............4-3
RADIATOR..................................................4-4
CARBURETOR AND REED VALVE...........4-7
CYLINDER HEAD , CYLINDER AND
PISTON.....................................................4-17
CLUTCH AND PRIMARY DRIVEN
GEAR.......................................................4-30
KICK AXLE, SHIFT SHAFT AND
PRIMARY DRIVE GEAR...........................4-37
YPVS GOVERNOR...................................4-45
WATER PUMP..........................................4-48
CDI MAGNETO.........................................4-52
ENGINE REMOVAL..................................4-56
CRANKCASE AND CRANKSHAFT.........4-61
TRANSMISSION, SHIFT CAM AND
SHIFT FORK.............................................4-69
CHAPTER 5
CHASSIS
FRONT WHEEL AND REAR WHEEL........5-1
FRONT BRAKE AND REAR BRAKE.......5-10
FRONT FORK...........................................5-26
HANDLEBAR............................................5-42
STEERING................................................5-50
SWINGARM..............................................5-55
REAR SHOCK ABSORBER.....................5-63
1C3-9-32-0 4/28/06 9:45 AM Page 20

CHAPTER 6
ELECTRICAL
ELECTRICAL COMPONENTS AND
WIRING DIAGRAM.....................................6-1
IGNITION SYSTEM.....................................6-2
CHAPTER 7
TUNING
ENGINE.......................................................7-1
CHASSIS...................................................7-13
1C3-9-32-0 4/28/06 9:45 AM Page 22

1-1
GEN
INFO
DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1Clutch lever
2“ENGINE STOP” button
3Front brake lever
4Throttle grip
5Radiator cap
6Fuel tank cap
7Kick starter
8Fuel tank
9Radiator
0Coolant drain bolt
qCheck bolt (Transmission oil level)
wRear brake pedal
eValve joint
rFuel cock
tAir cleaner
yDrive chain
uShift pedal
iStarter knob
oFront fork
NOTE:
9The machine you have purchased may differ
slightly from those shown in the following.
9Designs and specifications are subject to
change without notice.
1C3-9-32-1A 4/12/06 4:38 PM Page 2

1-1
GEN
INFO
DESCRIPTION
BESCHREIBUNG
DESCRIZIONE
ALLGEMEINE
ANGABEN
BESCHREIBUNG1Kupplungshebel
2Motorstoppknopf „ENGINE STOP“
3Handbremshebel
4Gasdrehgriff
5Kühlerdeckel
6Kraftstofftank-Verschluss
7Kickstarter
8Kraftstofftank
9Kühler
0Kühlmittel-Ablassschraube
qPrüfschraube (Getriebeölstand)
wFußbremshebel
eVentilverbindung
rKraftstoffhahn
tLuftfilter
yAntriebskette
uSchalthebel
iStarterknopf
oVorderradgabel
HINWEIS:
9Die von Ihnen gekaufte Maschine
könnte etwas von den hier gezeigten
Abbildungen abweichen.
9Änderungen des Designs und der
technischen Daten ohne vorherge-
hende Bekanntgabe sind vorbehal-
ten.
RENSEIGNEMENTS
GENERAUX
DESCRIPTION1Levier d’embrayage
2Bouton de coupe-circuit de sécurité
“ENGINE STOP”
3Levier de frein avant
4Poignée d’accélérateur
5Bouchon du radiateur
6Bouchon de réservoir à essence
7Kickstarter
8Réservoir de carburant
9Radiateur
0Boulon de vidange du liquide de
refroidissement
qBoulon de contrôle
(niveau d’huile de transmission)
wPédale de frein arrière
eJoint de robinet
rRobinet à essence
tFiltre à air
yChaîne de transmission
uPédale de sélecteur
iBouton de starter
oFourche avant
N.B.:
9La machine que vous avez achetée
diffère peutêtre partiellement de celles
montrées sur ces photos.
9La conception et les caractéristiques
peuvent êtres changées sans préavis.
IC100000
INFORMAZIONI
GENERALI
IC110000
DESCRIZIONE
1Leva di comando della frizione
2Pulsante “ARRESTO MOTORE”
3Leva di comando del freno anteriore
4Manopola dell’acceleratore
5Tappo del radiatore
6Tappo del serbatoio del carburante
7Pedivella della messa in moto
8Serbatoio del carburante
9Radiatore
0Bullone di drenaggio del liquido
refrigerante
qBullone di controllo
(livello dell’olio della trasmissione)
wPedale di comando del freno posteriore
eGiunto della valvola
rRubinetto del carburante
tFiltro dell’aria
yCatena di trasmissione
uPedale del cambio
iManopola dell’avviamento
oForcella anteriore
NOTA:
9Il veicolo acquistato può essere leg-
germente diverso da quelli illustrati
qui sotto.
9Progetti e specifiche sono soggetti a
variazioni senza preavviso.
1
1C3-9-32-1A 4/12/06 4:38 PM Page 3

1-2
GEN
INFO
MACHINE IDENTIFICATION
EC120001
MACHINE IDENTIFICATION
There are two significant reasons for knowing
the serial number of your machine:
1. When ordering parts, you can give the num-
ber to your Yamaha dealer for positive iden-
tification of the model you own.
2. If your machine is stolen, the authorities will
need the number to search for and identify
your machine.
EC121001
VEHICLE IDENTIFICATION NUMBER
(For USA, CDN, AUS, NZ and E)
The vehicle identification number 1is stamped
on the right of the steering head pipe.
EC122001
FRAME SERIAL NUMBER
(For F, D, GB, I and ZA)
The frame serial number 1is stamped on the
right of the steering head pipe.
EC123001
ENGINE SERIAL NUMBER
The engine serial number 1is stamped into the
elevated part of the right-side of the engine.
EC124000
MODEL LABEL
The model label 1is affixed to the frame under
the rider’s seat. This information will be needed
to order spare parts.
1C3-9-32-1A 4/12/06 4:38 PM Page 4