water pump YAMAHA YZ250LC 2001 Notices Demploi (in French)

CHAPTER 4
ENGINE
SEAT, FUEL TANK AND SIDE
COVERS.....................................................4-1
EXHAUST PIPE AND SILENCER..............4-3
RADIATOR..................................................4-4
CARBURETOR AND REED VALVE...........4-7
CYLINDER HEAD , CYLINDER AND
PISTON.....................................................4-17
CLUTCH AND PRIMARY DRIVEN
GEAR.......................................................4-32
KICK AXLE, SHIFT SHAFT AND
PRIMARY DRIVE GEAR...........................4-39
YPVS GOVERNOR...................................4-48
WATER PUMP..........................................4-50
CDI MAGNETO.........................................4-55
ENGINE REMOVAL..................................4-59
CRANKCASE AND CRANKSHAFT.........4-64
TRANSMISSION, SHIFT CAM AND
SHIFT FORK.............................................4-71
CHAPTER 5
CAHSSIS
FRONT WHEEL AND REAR WHEEL........5-1
FRONT BRAKE AND REAR BRAKE.......5-10
FRONT FORK...........................................5-27
HANDLEBAR............................................5-40
STEERING................................................5-47
SWINGARM..............................................5-52
REAR SHOCK ABSORBER.....................5-59
5MW-9-30-0 7/5/00 2:15 PM Page 20

1-3
IMPORTANT INFORMATION
GEN
INFO
EC130000
IMPORTANT INFORMATION
EC131010
PREPARATION FOR REMOVAL AND DIS
ASSEMBLY
1. Remove all dirt, mud, dust, and foreign
material before removal and disassembly.
When washing the machine with high pres-
sured water, cover the parts as follows.
9Silencer end
9Air filter intake slit
9Water pump housing hole at the bottom
2. Use proper tools and cleaning equipment.
Refer to “SPECIAL TOOLS” section.
3. When disassembling the machine, keep
mated parts together. They include gears,
cylinders, pistons, and other mated parts
that have been “mated” through normal
wear. Mated parts must be reused as an
assembly or replaced.
4. During the machine disassembly, clean all
parts and place them in trays in the order of
disassembly. This will speed up assembly
time and help assure that all parts are cor-
rectly reinstalled.
5. Keep away from fire.
5MW-9-30-1 7/3/00 1:37 PM Page 6

2-4
MAINTENANCE SPECIFICATIONSSPEC
Item Standard Limit
Transmission:
Main axle deflection limit…
0.01 mm (0.0004 in)
Drive axle deflection limit…
0.01 mm (0.0004 in)
Shifter:
Shifting type Cam drum and guide bar…
Guide bar bending limit…
0.05 mm (0.0020 in)
Kick starter type: Kick and ratchet type…
Air filter oil grade (oiled filter):Foam-air-filter oil or engine mixing oil…
Carburetor:USA, CDN, ZA,
EUROPE
AUS, NZ
Type/Manufacturer
PWK38S/KEIHIN¬…
I.D. mark 5MW00 5MW10…
Main jet (M.J.) #178 #180…
Main air jet (M.A.J) #200¬…
Jet needle-clip position (J.N.) N3EJ-2 N3CW-3…
Main nozzle (N.J.) ø2.9¬…
Cutaway (C.A.) #7¬…
Pilot jet (P.J.) #50 #55…
Pilot air screw (P.A.S.) 1 1-3/4…
(for reference only)
Valve seat size (V.S.)
ø3,8 mm (0,15 in)¬…
Starter jet (G.S.) #85¬…
Power jet (P.W.J.) #50 #55 …
Float arm height (F.H.) 5.5~7.5 mm¬…
(0.22~030 in)
Reed valve:
Thickness* 0.42 mm (0.017 in)…
Valve stopper height 10.3~10.7 mm (0.406~0.421 in)…
Valve bending limit…
0.2 mm (0.008 in)
Cooling:
Radiator core size:
Width 110 mm (4.33 in)…
Height 240 mm (9.45 in)…
Thickness 32 mm (1.26 in)…
Radiator cap opening pressure 95~125 kPa…
(0.95~1.25 kg/cm
2, 13.5~17.8 psi)
Radiator capacity (total) 0.64 L (0.56 Imp qt, 0.68 US qt)…
Water pump:
Type Single-suction centrifugal pump…
5MW-9-30-2 7/3/00 2:20 PM Page 5

2-5
MAINTENANCE SPECIFICATIONSSPEC
Part to be tightened Thread size Q’tyT ightening torqueNm m•kg ft•lb
Spark plug M14 ´1.25 1 20 2.0 14
Cylinder head (nut) M 8 ´1.25 6 25 2.5 18
(stud) M 8 ´1.25 6 13 1.3 9.4
Cylinder (nut) M10 ´1.25 4 35 3.5 25
(stud) M10 ´1.25 4 13 1.3 9.4
Power valve :
Holder M 5 ´0.8 2 6 0.6 4.3
Link rod M 5 ´0.8 2 6 0.6 4.3
Push rod M 5 ´0.8 1 5 0.5 3.6
Thrust plate M 5 ´0.8 1 6 0.6 4.3
Side holder M 5 ´0.8 4 4 0.4 2.9
Link lever M 4 ´0.7 1 4 0.4 2.9
Pulley M 4 ´0.7 2 4 0.4 2.9
Cover M 5 ´0.8 4 4 0.4 2.9
Governor fork M 4 ´0.7 2 5 0.5 3.6
Housing M 5 ´0.8 4 5 0.5 3.6
Impeller M 8 ´1.25 1 14 1.4 10
Water pump housing cover M 6 ´1.0 4 10 1.0 7.2
Coolant drain bolt M 6 ´1.0 1 10 1.0 7.2
Radiator M 6 ´1.0 6 10 1.0 7.2
Radiator hose clamp M 6 ´1.0 8 1 0.1 0.7
Air filter element M 6 ´1.0 1 2 0.2 1.4
Carburetor joint M 6 ´1.0 5 10 1.0 7.2
Air filter case M 6 ´1.0 2 4 0.4 2.9
Air filter joint M 5 ´0.8 5 1 0.1 0.7
Reed valve M 3 ´0.5 4 1 0.1 0.7
Exhaust pipe M 6 ´1.0 2 12 1.2 8.7
Exhaust pipe stay (front) M 8 ´1.25 1 25 2.5 18
Exhaust pipe stay (rear) M 6 ´1.0 1 12 1.2 8.7
Silencer (front) M 6 ´1.0 1 12 1.2 8.7
Silencer (rear) M 6 ´1.0 1 7 0.7 5.1
Fiber (silencer) M 6 ´1.0 2 10 1.0 7.2
Crankcase M 6 ´1.0 11 14 1.4 10
Crankcase cover (left) M 6 ´1.0 5 8 0.8 5.8
Chain cover M 6 ´1.0 2 8 0.8 5.8
Crankcase cover (right) M 6 ´1.0 9 10 1.0 7.2
Bearing plate cover (drive axle left) M 6 ´1.0 2 10 1.0 7.2
Bearing plate cover (main axle right) M 6 ´1.0 2 10 1.0 7.2
Holder M 6 ´1.0 2 10 1.0 7.2
Oil drain bolt M12 ´1.5 1 20 2.0 14
Oil check bolt M 6 ´1.0 1 10 1.0 7.2
Kick starter M 8 ´1.25 1 30 3.0 22
Ratchet wheel stopper M 6 ´1.0 2 10 1.0 7.2
Clutch cover M 6 ´1.0 6 10 1.0 7.2
Primary drive gear M10 ´1.25 1 55 5.5 40
Clutch boss M20 ´1.0 1 75 7.5 54
5MW-9-30-2 7/3/00 2:20 PM Page 6

4-39
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE GEARENG
Extent of removal Order Part name Q’ty Remarks
RPIMARY DRIVE GEAR REMOVAL
Preparation for Drain the transmission oil.Refer to “TRANSMISSION OIL REPLACE-
removalMENT“ section in the CHAPTER 3.
Bolt (brake pedal) Shift the brake pedal downward.
Radiator hose 4 Disconnect at water pump side.
Bolt (push rod)
Refer to “CYLINDER HEAD, CYLINDER
AND PISTON” section.
1 Kick starter 1
2 Crankcase cover (right) 1
3 Bolt (Primary drive gear) 1 Only loosening
Refer to “REMOVAL POINTS”.
4 Primary driven gear 1 Refer to “CLUTCH AND PRIMARY
DRIVEN GEAR”section.
5 Primary drive gear 1
6 Thrust plate 1
EC4C0000
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE GEAREC4C8000
PRIMARY DRIVE GEAR
1
Extent of removal:1Primary drive gear removal
30 Nm (3.0 m•kg, 22 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
55 Nm (5.5 m•kg, 40 ft•lb)
5MW-9-30-4B 7/3/00 7:05 PM Page 26

4-51
WATER PUMPENG
EC4G0000
WATER PUMP
Extent of removal:1Impeller shaft removal2Oil seal removal
Extent of removal Order Part name Q’ty Remarks
WATER PUMP DISASSEMBLY
Preparation for Crankcase cover (right)
Refer to “KICK AXLE, SHIFT SHAFT AND
removalPRIMARY DRIVE GEAR” section.
1 Water pump housing cover 1
2 Impeller 1
3 Plain washer 1 Refer to “REMOVAL POINTS”.
4 Impeller shaft 1
5 Bearing 1
6 Oil seal 2Refer to “REMOVAL POINTS”.
1
2ü
ï
ý
ï
þ
ü
ý
þ
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
5MW-9-30-4C 7/3/00 7:41 PM Page 6

4-52
WATER PUMPENG
EC4G3000
REMOVAL POINTS
EC4G3110
Impeller shaft
1. Remove:
9Impeller 1
9Plain washer 2
9Impeller shaft 3
NOTE:
Hold the impeller shaft on its width across the
flats awith spanners, etc. and remove the
impeller.
EC4G3210
Oil seal
NOTE:
It is not necessary to disassemble the water
pump, unless there is an abnormality such as
excessive change in coolant level, discoloration
of coolant, or milky transmission oil.
1. Remove:
9Bearing 1
2. Remove:
9Oil seal 1
EC4G4000
INSPECTIONEC444200
Impeller shaft
1. Inspect:
9Impeller shaft 1
Bend/Wear/Damage
ÕReplace.
Fur deposits
ÕClean.
5MW-9-30-4C 7/3/00 7:42 PM Page 8

4-53
WATER PUMPENG
EC444300
Impeller shaft gear
1. Inspect:
9Gear teeth a
Wear/Damage
ÕReplace.
EC4H4600
Bearing
1. Inspect:
9Bearing 1
Rotate inner race with a finger.
Rough spot/Seizure
ÕReplace.
EC444400
Oil seal
1. Inspect:
9Oil seal 1
Wear/Damage
ÕReplace.
EC4G5000
ASSEMBLY AND INSTALLATION
EC4G5111
Oil seal
1. Install:
9Oil seal 1
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture's marks
or numbers facing the crankcase cover (right)
2.
2. Install:
9Bearing 1
NOTE:
Install the bearing by pressing its outer race par-
allel.
5MW-9-30-4C 7/3/00 7:42 PM Page 10

4-54
WATER PUMPENG
EC4G5220
Impeller shaft
1. Install:
9Impeller shaft 1
NOTE:
9Take care so that the oil seal lip is not damaged
or the spring does not slip off its position.
9When installing the impeller shaft, apply the
lithium soap base grease on the oil seal lip and
impeller shaft. And install the shaft while turn-
ing it.
2. Install:
9Plain washer 1
9Impeller 2
NOTE:
Hold the impeller shaft on its width across the
flats awith spanners, etc. and install the
impeller.
3. Install:
9Dowel pin 1
9Gasket (water pump housing cover) 2
4. Install:
9Water pump housing cover 1
9Bolt (water pump housing cover) 2
9Copper washer (coolant drain bolt) 3
9Coolant drain bolt 4
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
5MW-9-30-4C 7/3/00 7:43 PM Page 12