transmission oil YAMAHA YZ250LC 2003 Manuale duso (in Italian)

4-51
YPVS GOVERNORENG
4. Install:
9Governor assembly 1
NOTE:
Align the groove ain the governor with the fork
band set the governor in the crankcase cover.
3. Install:
9Dowel pin 1
NOTE:
9While compressing the spring, install the dowel
pin.
9Make sure the dowel pin fits into the groove a
in the retainer.
2. Install:
9Ball 1
9Retainer 2
To governor shaft 3.
NOTE:
Apply the transmission oil on the retainer and
ball.
5UP-9-30-4C 5/24/02 5:32 PM Page 4

4-53
WATER PUMPENG
EC4G3000
REMOVAL POINTS
EC4G3110
Impeller shaft
1. Remove:
9Impeller 1
9Plain washer 2
9Impeller shaft 3
NOTE:
Hold the impeller shaft on its width across the
flats awith spanners, etc. and remove the
impeller.
EC4G3210
Oil seal
NOTE:
It is not necessary to disassemble the water
pump, unless there is an abnormality such as
excessive change in coolant level, discoloration
of coolant, or milky transmission oil.
1. Remove:
9Bearing 1
2. Remove:
9Oil seal 1
EC4G4000
INSPECTIONEC444200
Impeller shaft
1. Inspect:
9Impeller shaft 1
Bend/Wear/Damage
Replace.
Fur deposits
Clean.
5UP-9-30-4C 5/24/02 5:32 PM Page 8

4-69
CRANKCASE AND CRANKSHAFTENG
EC4N5283
Crankshaft
1. Install:
9Crankshaft 1
Use the crankshaft installing tool 2, 3, 4.
EC4N5102
Oil seal
1. Install:
9Oil seal (left) 1
9Oil seal (right) 2
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture’s marks
or numbers facing outward.
Crankshaft installing tool:
Pot 2:
YU-90050/90890-01274
Bolt 3:YU-90050/90890-01275
Adapter 4:YU-90063/90890-01278
2. Check:
9Shifter operation
9Transmission operation
Unsmooth operation
Repair.
å åB
åFor USA and CDN
∫Except for USA and CDN
NOTE:
9Hold the connecting rod at top dead center with
one hand while turning the nut of the installing
tool with the other. Operate the installing tool
until the crankshaft bottoms against the bear-
ing.
9Before installing the crankshaft, clean the con-
tacting surface of crankcase.
9Apply the lithium soap base grease on the oil
seal lip.
cC
Do not use a hammer to drive in the crank-
shaft.
5UP-9-30-4C 5/24/02 5:33 PM Page 40

4-71
CRANKCASE AND CRANKSHAFTENG
8. Tighten:
9Segment 1
9Bolt (segment) 2
NOTE:
9When installing the segment onto the shift cam
3, align the punch mark awith the dowel pin
b.
9Turn the segment clockwise until it stops and
tighten the bolt.
30 Nm (3.0 m•kg, 22 ft•lb)
7. Install:
9Tension spring 1
9Holder 2
9Bolt (holder) 3
NOTE:
Install the holder so that it contacts the projec-
tion aon the crankcase (right).
10 Nm (1.0 m•kg, 7.2 ft•lb)
9. Remove:
9Sealant
Forced out on the cylinder mating surface.
10. Apply:
9Engine oil
To the crank pin, bearing, oil delivery hole
and connecting rod big end washer.
11. Check:
9Crankshaft and transmission operation
Unsmooth operation
Repair.
5UP-9-30-4C 5/24/02 5:33 PM Page 44

4-74
TRANSMISSION, SHIFT CAM AND SHIFT FORKENG
EC4H5000
ASSEMBLY AND INSTALLATION
EC4H5242
Transmission
1. Install:
95th pinion gear (21T) 1
93rd pinion gear (18T) 2
9Collar 3
94th pinion gear (22T) 4
92nd pinion gear (15T) 5
To main axle 6.
NOTE:
9Apply the molybdenum disulfide oil on the 4th
and 5th pinion gears inner circumference and
on the end surface.
9Apply the molybdenum disulfide oil on the 2nd
and 3rd pinion gears inner circumference.
3. Check:
9Shift fork movement
Unsmooth operation
Replace shift fork.
NOTE:
For a malfunctioning shift fork, replace not only
the shift fork itself but the two gears each adja-
cent to the shift fork.
2. Inspect:
9Shift cam 1
9Segment 2
Wear/Damage
Replace.
EC4H4810
Shift fork, shift cam and segment
1. Inspect:
9Shift fork 1
Wear/Damage/Scratches
Replace.
5UP-9-30-4C 5/24/02 5:33 PM Page 50

4-75
TRANSMISSION, SHIFT CAM AND SHIFT FORKENG
4. Install:
9Spacer 1
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9When installing the spacer into the crankcase,
pay careful attention to the crankcase oil seal
lip.
9Install the spacer with its chamfered side a
facing the crankcase.
3. Install:
9Plain washer 1
9Circlip 2
NOTE:
9Be sure the circlip sharp-edged corner ais
positioned opposite side to the plain washer
and gear b.
9Be sure the circlip end cis positioned at axle
spline groove d.
2. Install:
92nd wheel gear (23 T) 1
94th wheel gear (24 T) 2
93rd wheel gear (23 T) 3
95th wheel gear (20 T) 4
91st wheel gear (27 T) 5
9O-ring 6
To drive axle 7.
NOTE:
9Apply the molybdenum disulfide oil on the 1st,
2nd and 3rd wheel gears inner circumference
and on the end surface.
9Apply the molybdenum disulfide oil on the 4th
and 5th wheel gears inner circumference.
9Apply the lithium soap base grease on the O-
ring.
5UP-9-30-4C 5/24/02 5:33 PM Page 52

4-76
TRANSMISSION, SHIFT CAM AND SHIFT FORKENG
5. Install:
9Shift fork 1 (L) 1
9Shift fork 2 (C10) 2
9Shift fork 3 (R) 3
9Shift cam 4
To main axle and drive axle.
NOTE:
9Apply the molybdenum disulfide oil on the shift
fork grooves.
9Mesh the shift fork #1 (L) with the 4th wheel
gear 5and #3 (R) with the 5th wheel gear 7
on the drive axle.
9Mesh the shift fork #2 (C10) with the 3rd pinion
gear 6on the main axle.
6. Install:
9Transmission assembly 1
To crankcase (left) 2.
NOTE:
Apply the transmission oil on the bearings and
guide bars.
7. Check:
9Shifter operation
9Transmission operation
Unsmooth operation
Repair.
5UP-9-30-4C 5/24/02 5:33 PM Page 54

5-3
CHAS
ROUE AVANT ET ROUE ARRIERE
VORDERRAD UND HINTERRAD
RUOTA ANTERIORE E RUOTA POSTERIORE
AUSBAUPUNKTE
Hinterrad
1. Ausbauen:
9Rad 1
HINWEIS:
Das Rad nach vorne stoßen und die
Antriebskette 2abnehmen.
Radlager (wenn erforderlich)
1. Ausbauen:
9Lager 1
HINWEIS:
Das Lager unter Verwendung einer
allgemeinen Lager-Abziehvorrichtung
2ausbauen.
INSPEKTION
Rad
1. Messen:
9Felgenschlag
Außerhalb des Grenzwertes
Reparieren/Erneuern.
2. Prüfen:
9Lager
Den inneren Laufring mit
einem Finger drehen.
Rauhe Stellen/Freßspuren
Erneuern.
HINWEIS:
Die Lager, die Öldichtung und die
Radhülse als Satz erneuern.
POINTS DE DEPOSE
Roue arrière
1. Déposer:
9Roue 1
N.B.:
Pousser la roue vers l’avant et déposer
la chaîne de transmission 2.
Roulement de roue (si nécessaire)
1. Déposer:
9Roulement 1
N.B.:
Déposer le roulement en utilisant un
arrache-roulement courant 2.
VERIFICATION
Roue
1. Mesure:
9Voile de roue
Hors limiteRéparer/Changer.
2. Examiner:
9Roulement
Faire tourner la bague intérieure
avec le doigt.
Point dur/grippage’Changer.
N.B.:
Changer les roulements, la bague
d’étanchéité et la collerette de roue
comme un ensemble.
IC593000PUNTI DI RIMOZIONE
IC523101
Ruota posteriore
1. Togliere:
9Ruota 1
NOTA:
Spingere in avanti la ruota e togliere la
catena di trasmissione 2.
IC513201
Cuscinetto della ruota (se necessario)
1. Togliere:
9Cuscinetto 1
NOTA:
Togliere il cuscinetto usando un estrat-
tore generico per cuscinetti 2.
IC594000
ISPEZIONE
IC514100
Ruota
1. Misurare:
9Scentratura della ruota
Fuori limite
Ripararla/Sostituirla.
2. Ispezionare:
9Cuscinetto
Ruotare l’anello interno con un
dito.
Ruvidità/Grippaggio
Sostituir-
lo.
NOTA:
Sostituire i cuscinetti, il paraolio e il
bordino della ruota come set.
Limite de voile de la roue:
Radial 1 1
: 2,0 mm
(0,08 in)
Latéral 2 2
: 2,0 mm
(0,08 in)
Limite di scentratura
della ruota:
Radiale 1 1
: 2,0 mm
(0,08 in)
Laterale 2 2
: 2,0 mm
(0,08 in)
Felgen-Verschleißgrenze:Senkrecht 1 1
: 2,0 mm
(0,08 in)
Seitlich 2 2
: 2,0 mm
(0,08 in)
5UP-9-30-5AN 5/24/02 5:41 PM Page 7