length YAMAHA YZ250LC 2006 Manuale duso (in Italian)

5. GASOLINE IS HIGHLY FLAMMABLE.
Always turn off the engine while refuel-
ing. Take care to not spill any gasoline
on the engine or exhaust system.
Never refuel in the vicinity of an open
flame, or while smoking.
6. GASOLINE CAN CAUSE INJURY.
If you should swallow some gasoline,
inhale excess gasoline vapors, or allow
any gasoline to get into your eyes, con-
tact a doctor immediately. If any gaso-
line spills onto your skin or clothing,
immediately wash skin areas with soap
and water, and change your clothes.
7. ONLY OPERATE THE MACHINE IN AN
AREA WITH ADEQUATE VENTILATION.
Never start the engine or let it run for
any length of time in an enclosed area.
Exhaust fumes are poisonous. These
fumes contain carbon monoxide, which
by itself is odorless and colorless.
Carbon monoxide is a dangerous gas
which can cause unconsciousness or
can be lethal.
8. PARK THE MACHINE CAREFULLY;
TURN OFF THE ENGINE.
Always turn off the engine if you are
going to leave the machine. Do not
park the machine on a slope or soft
ground as it may fall over.
9. PROPERLY SECURE THE MACHINE
BEFORE TRANSPORTING IT.
When transporting the machine in
another vehicle, always be sure it is
properly secured and in an upright
position and that the fuel cock is in the
“OFF” position. Otherwise, fuel may
leak out of the carburetor or fuel tank.
1P8-9-31-0 5/12/05 10:58 AM Page 6

2-1
GENERAL SPECIFICATIONSSPEC
Model name: YZ250V (USA, CDN)
YZ250 (EUROPE, ZA)
YZ250V (AUS, NZ)
Model code number: 1P85 (USA, CDN)
1P86 (EUROPE)
1P88 (AUS, NZ, ZA)
Dimensions:USA, AUS, NZ, ZACDN EUROPE
Overall length 2,178 mm 2,182 mm 2,184 mm
(85.7 in) (85.9 in) (86.0 in)
Overall width 827 mm←←
(32.6 in)
Overall height 1,305 mm 1,308 mm 1,309 mm
(51.4 in) (51.5 in) (51.5 in)
Seat height 994 mm 996 mm 997 mm
(39.1 in) (39.2 in) (39.3 in)
Wheelbase 1,481 mm←←
(58.3 in)
Minimum ground clearance 382 mm 384 mm 385 mm
(15.0 in) (15.1 in) (15.2 in)
Dry weight:
Without oil and fuel 96.0 kg (211.6 lb)
Engine:
Engine type Liquid cooled 2-stroke, gasoline
Cylinder arrangement Single cylinder, forward inclined
Displacement 249 cm
3(8.76 lmp oz, 8.42 US oz)
Bore ×Stroke 66.4 ×72 mm (2.614 ×2.835 in)
Compression ratio 9.2~10.9 : 1 (For USA and CDN)
8.9~10.6 : 1 (For EUROPE, AUS, NZ and ZA)
Starting system Kick starter
Lubrication system: Premix (30 : 1)(Yamalube 2-R)
Oil type or grade (2-Cycle):
Transmission oil Yamalube 4 (10W-30) or SAE 10W-30 type SE
motor oil
Periodic oil change 0.75 L (0.66 Imp qt, 0.79 US qt)
Total amount 0.80 L (0.70 Imp qt, 0.85 US qt)
Coolant capacity (including all routes): 1.20 L (1.06 Imp qt, 1.27 US qt)
Air filter: Wet type element
Fuel:
Type Premium unleaded gasoline
only with a research octane
number of 95 or higher
Tank capacity 8.0 L (1.76 Imp gal, 2.11 US gal)
EC200000
SPECIFICATIONSEC211000
GENERAL SPECIFICATIONS
1P8-9-31-2 5/19/05 10:30 AM Page 2

2-3
MAINTENANCE SPECIFICATIONSSPEC
Item Standard Limit
Cylinder head:
USA, CDNEUROPE,
AUS, NZ, ZA
Combustion chamber capacity 21.0 cm
321.5 cm3…
(0.739 Imp oz, (0.757 Imp oz,
0.710 US oz) 0.727 US oz)
Warp limit……
0.03 mm (0.0012 in)
Cylinder:
Bore size 66.400~66.414 mm 66.5 mm (2.618 in)
(2.6142~2.6147 in)
Taper limit…
0.05 mm (0.0020 in)
Out of round limit…
0.01 mm (0.0004 in)
Piston:
Piston size/ 66.352~66.367 mm…
(2.6120~2.6129 in)
Measuring point* 17.5 mm (0.69 in)…
Piston clearance 0.045~0.050 mm 0.1 mm (0.004 in)
(0.0018~0.0020 in)
Piston offset 1.5 mm (0.059 in)/EX-side…
Piston pin:
Piston pin outside diameter 17.995~18.000 mm 17.975 mm
(0.7085~0.7087 in) (0.7077 in)
Piston ring:
Sectional sketch Plain…
B=1.0 mm (0.039 in)…
T=2.55 mm (0.100 in)…
End gap (installed) 0.40~0.55 mm (0.016~0.022 in) 0.95 mm (0.037 in)
Side clearance (installed) : 1st
0.030~0.065 mm (0.0012~0.0026 in)0.1 mm (0.004 in)
: 2nd0.030~0.065 mm (0.0012~0.0026 in)0.1 mm (0.004 in)
Crankshaft:
Crank width “A” 59.95~60.00 mm (2.360~2.362 in)…
Runout limit “C” 0.03 mm (0.0012 in) 0.05 mm (0.0020 in)
Connecting rod big end
side clearance “D” 0.25~0.75 mm (0.010~0.030 in)…
Small end free play “F” 0.4~1.0 mm (0.016~0.039 in) 2.0 mm (0.08 in)
Clutch:
Friction plate thickness 2.9~3.1 mm (0.114~0.122 in) 2.8 mm (0.110 in)
Quantity 8 …
Clutch plate thickness 1.5~1.7 mm (0.059~0.067 in) …
Quantity 7 …
Warp limit … 0.2 mm (0.008 in)
Clutch spring free length 50.0 mm (1.969 in) 48.0 mm (1.890 in)
Quantity 6 …
EC212000
MAINTENANCE SPECIFICATIONSEC212100
ENGINE
1P8-9-31-2 5/19/05 10:30 AM Page 4

2-7
MAINTENANCE SPECIFICATIONSSPEC
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing…
Front suspension: USA, CDN, ZA,
EUROPE
AUS, NZ
Front fork travel
300 mm (11.8 in)←…
Fork spring free length
454 mm (17.9 in)←449 mm (17.7 in)
Spring rate, STD K=4.2 N/mm←…
(0.428 kg/mm,
24.0 lb/in)
Optional spring Yes←…
Oil capacity 527 cm
3532 cm3…
(18.6 Imp oz, (18.7 Imp oz,
17.8 US oz) 18.0 US oz)
Oil grade Suspension oil ←…
“S1”
Inner tube outer diameter 48 mm (1.89 in)←…
Front fork top endZero mm (Zero in)←…
Rear suspension: USA, CDN, ZA,
EUROPE
AUS, NZ
Shock absorber travel
131.5 mm (5.18 in)←…
Spring free length
Approx. 265 mm←…
(10.43 in)
Fitting length
One I.D. paint mark One I.D. paint mark
255 mm (10.04 in) 252 mm (9.92 in)…
Two I.D. paint marks Two I.D. paint marks
261 mm (10.28 in) 258 mm (10.16 in)…
Three I.D. paint marks Three I.D. paint marks
252.5 mm (9.94 in)249.5 mm (9.82 in)…

One I.D. paint mark
245.5 ~ 263.5 mm←…
(9.67 ~ 10.37 in)
Two I.D. paint marks
251.5 ~ 269.5 mm←…
(9.90 ~ 10.61 in)
Three I.D. paint marks
243.0 ~ 261.0 mm←…
(9.57 ~ 10.28 in)
Spring rate, STDK=48.0 N/mm ←…
(4.90 kg/mm,
274.4 lb/in)
Optional spring Yes←…
Enclosed gas pressure 1,000 kPa ←…
(10 kg/cm
2,
142 psi)
Swingarm:
Swingarm free play limit
End…
1.0 mm (0.04 in)
Side clearance…
0.2~0.9 mm
(0.008~0.035 in)
1P8-9-31-2 5/19/05 10:30 AM Page 8

2-8
MAINTENANCE SPECIFICATIONSSPEC
Item Standard Limit
Wheel:
Front wheel type Spoke wheel…
Rear wheel type Spoke wheel…
Front rim size/Material 21 ×1.60/Aluminum…
Rear rim size/Material 19 ×2.15/Aluminum…
Rim runout limit:
Radial…
2.0 mm (0.08 in)
Lateral…
2.0 mm (0.08 in)
Drive chain
Type/Manufacturer DID520DMA2 SDH/DAIDO…
Number of links 113 links + joint…
Chain slack 48~58 mm (1.9~2.3 in)…
Chain length (15 links)…
242.9 mm (9.563 in)
Front disc brake:
Disc outside dia. ×Thickness 250 ×3.0 mm 250 ×2.5 mm
(9.84 ×0.12 in) (9.84 ×0.10 in)
Pad thickness 4.4 mm (0.17 in) 1.0 mm (0.04 in)
Master cylinder inside dia. 11.0 mm (0.433 in)…
Caliper cylinder inside dia. 27.0 mm (1.063 in) ×2…
Brake fluid type DOT #4…
Rear disc brake:
Disc outside dia. ×Thickness 245 ×4.0 mm 245 ×3.5 mm
(9.65 ×0.16 in) (9.65 ×0.14 in)
Deflection limit…
0.15 mm (0.006 in)
Pad thickness 6.4 mm (0.25 in) 1.0 mm (0.04 in)
Master cylinder inside dia. 11.0 mm (0.433 in)…
Caliper cylinder insdie dia. 25.4 mm (1.000 in)…
Brake fluid type DOT #4…
Brake lever & brake pedal:
Brake lever position 95 mm (3.74 in)…
Brake pedal height Zero mm (Zero in)…
(vertical height above footrest top)
Clutch lever free play (lever end) 8~13 mm (0.31~0.51 in)…
Throttle grip free play 3~5 mm (0.12~0.20 in)…
1P8-9-31-2 5/19/05 10:30 AM Page 9

2-13
GENERAL TORQUE SPECIFICATIONS/
DEFINITION OF UNITS
SPEC
This chart specifies torque for standard faste-
ners with standard I.S.O. pitch threads. Torque
specifications for special components or assem-
blies are included in the applicable sections of
this book. To avoid warpage, tighten multi-faste-
ner assemblies in a crisscross fashion, in pro-
gressive stages, until full torque is reached.
Unless otherwise specified, torque specifications
call for clean, dry threads. Components should
be at room temperature.
A: Distance across flats
B: Outside thread diameter
EC230000
DEFINITION OF UNITS
EC220001
GENERAL TORQUE SPECIFICATIONS
ABTORQUE SPECIFICATION
(Nut) (Bolt)
Nm m•kg ft•lb
10 mm 6 mm 6 0.6 4.3
12 mm 8 mm 15 1.5 11
14 mm 10 mm 30 3.0 22
17 mm 12 mm 55 5.5 40
19 mm 14 mm 85 8.5 61
22 mm 16 mm 130 13 94
Unit Read Definition Measure
mm milimeter 10-
3meter Length
cm centimeter 10-2meter Length
kg kilogram 103gram Weight
N Newton 1 kg ×m/sec2Force
Nm Newton meter N ×m Torque
m•kg Meter kilogrma m ×kg Torque
Pa Pascal N/m2Pressure
N/mm Newton per millimeter N/mm Spring rate
L Liter — Volume or capacity
cm3Cubic centimeter — Volume or capacity
r/min Revolution per minute — Engine speed
1P8-9-31-2 5/19/05 10:30 AM Page 14

3-24
SPROCKETS INSPECTION/DRIVE CHAIN INSPECTION
INSP
ADJ
EC368000
SPROCKETS INSPECTION
1. Inspect:
9Sprocket teeth a
Excessive wear Replace.
NOTE:
Replace the drive, driven sprockets and drive
chain as a set.
NOTE:
9While measuring the drive chain length push
down on the drive chain to increase its tension.
9Measure the length between drive chain roller
1and y as shown.
9Perform this measurement at two or three dif-
ferent places.
2. Remove:
9Master link clip
9Joint 1
9Drive chain 2
3. Clean:
9Drive chain
Place it in kerosene, and brush off as much
dirt as possible. Then remove the chain
from the kerosene and dry the chain.
EC369002
DRIVE CHAIN INSPECTION
1. Measure:
9Drive chain length (15 links) a
Out of specificationReplace.
Drive chain length (15 links):
Limit: 242.9 mm (9.563 in)
1P8-9-31-3B 5/13/05 11:44 AM Page 12

3-30
REAR SHOCK ABSORBER SPRING PRELOAD
ADJUSTMENTINSP
ADJ
NOTE:
9Be sure to remove all dirt and mud from around
the locknut and adjuster before
adjustment.
9The length of the spring (installed) changes 1.5
mm (0.06 in) per turn of the adjuster.
9The I.D. color bis marked at the end of the
spring.
cC
Never attempt to turn the adjuster beyond
the maximum or minimum setting.
EC36M014
REAR SHOCK ABSORBER SPRING
PRELOAD ADJUSTMENT
1. Elevate the rear wheel by placing the suit-
able stand under the engine.
2. Remove:
9Rear frame
3. Loosen:
9Locknut 1
4. Adjust:
9Spring preload
By turning the adjuster 2.
Stiffer Increase the spring preload.
(Turn the adjuster 2 2
in.)
Softer Decrease the spring pre-
load. (Turn the adjuster 2 2
out.)
Extent of adjustment
245.5~263.5 mm
(9.67~10.37 in)
251.5~269.5 mm
(9.90~10.61 in)
243.0~261.0 mm
(9.57~10.28 in)
Spring length (installed) a a
:
Standard length
One I.D. paint mark
255 mm (10.04 in)
*252 mm (9.92 in)
Two I.D. paint marks
261 mm (10.28 in)
*258 mm (10.16 in)
Three I.D. paint marks
252.5 mm (9.94 in)
*249.5 mm (9.82 in)
*For EUROPE
1P8-9-31-3B 5/13/05 11:44 AM Page 24

4-35
CLUTCH AND PRIMARY DRIVEN GEARENG
EC493000
REMOVAL POINTS
EC483211
Clutch boss
1. Remove:
9Nut 1
9Lock washer 2
9Clutch boss 3
NOTE:
Straighten the lock washer tab and use the
clutch holding tool 4, 5to hold the clutch boss.
åFor USA and CDN
∫Except for USA and CDN
EC494000
INSPECTION
EC484100
Clutch housing and boss
1. Inspect:
9Clutch housing 1
Cracks/Wear/Damage  Replace.
9Clutch boss 2
Scoring/Wear/Damage Replace.
EC484201
Primary driven gear
1. Check:
9Circumferential play
Free play exists Replace.
9Gear teeth a
Wear/ Damage Replace.
EC484400
Clutch spring
1. Measure:
9Clutch spring free length a
Out of specification Replace springs as
a set.
Clutch holding tool:
YM-91042................................4 4
90890-04086............................5 5
Clutch spring free length:
Standard
50.0 mm 48.0 mm
(1.969 in) (1.890 in)
å
∫å
1P8-9-31-4B 4/29/05 3:07 PM Page 16

5-31
CHASFRONT FORK
Base valve
1. Inspect:
9Base valve 1
Wear/DamageReplace.
ContaminationClean.
9O-ring 2
Wear/DamageReplace.
9Piston metal 3
Wear/DamageReplace.
9Spring 4
Damage/FatigueReplace base valve.
9Air bleed screw 5
Wear/DamageReplace.
EC554400
Fork spring
1. Measure:
9Fork spring free length a
Out of specificationReplace.
Standard
454 mm 449 mm
(17.9 in) (17.7 in)Fork spring free length:
Collar
1. Inspect:
9Piston metal 1
Wear/Damage Replace.
1P8-9-31-5B 5/12/05 10:57 AM Page 12