oil YAMAHA YZ250LC 2007 Betriebsanleitungen (in German)

4-52
WATER PUMPENG
EC4G0000
WATER PUMP
Extent of removal:1Impeller shaft removal2Oil seal removal
Extent of removal Order Part name Q’ty Remarks
WATER PUMP DISASSEMBLY
Preparation for Crankcase cover (right)
Refer to “KICK AXLE, SHIFT SHAFT AND
removalPRIMARY DRIVE GEAR” section.
1 Water pump housing cover 1
2 Impeller 1
3 Plain washer 1Refer to “REMOVAL POINTS”.
4 Impeller shaft 1
5 Bearing 1
6 Oil seal 2Refer to “REMOVAL POINTS”.
1
2







10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
1P8-9-32-4c 5/1/06 10:46 AM Page 6

4-53
WATER PUMPENG
EC4G3000
REMOVAL POINTS
EC4G3110
Impeller shaft
1. Remove:
9Impeller 1
9Plain washer 2
9Impeller shaft 3
NOTE:
Hold the impeller shaft on its width across the
flats awith spanners, etc. and remove the
impeller.
EC4G3210
Oil seal
NOTE:
It is not necessary to disassemble the water
pump, unless there is an abnormality such as
excessive change in coolant level, discoloration
of coolant, or milky transmission oil.
1. Remove:
9Bearing 1
2. Remove:
9Oil seal 1
EC4G4000
INSPECTIONEC444200
Impeller shaft
1. Inspect:
9Impeller shaft 1
Bend/Wear/Damage
Replace.
Fur deposits
Clean.
1P8-9-32-4c 5/1/06 10:46 AM Page 8

4-54
WATER PUMPENG
EC444300
Impeller shaft gear
1. Inspect:
9Gear teeth a
Wear/Damage
Replace.
EC4H4600
Bearing
1. Inspect:
9Bearing 1
Rotate inner race with a finger.
Rough spot/Seizure
Replace.
EC444400
Oil seal
1. Inspect:
9Oil seal 1
Wear/Damage
Replace.
EC4G5000
ASSEMBLY AND INSTALLATION
EC4G5111
Oil seal
1. Install:
9Oil seal 1
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture’s marks
or numbers facing the crankcase cover (right)
2.
2. Install:
9Bearing 1
NOTE:
Install the bearing by pressing its outer race par-
allel.
1P8-9-32-4c 5/1/06 10:46 AM Page 10

4-55
WATER PUMPENG
EC4G5220
Impeller shaft
1. Install:
9Impeller shaft 1
NOTE:
9Take care so that the oil seal lip is not damaged
or the spring does not slip off its position.
9When installing the impeller shaft, apply the
lithium soap base grease on the oil seal lip and
impeller shaft. And install the shaft while turn-
ing it.
2. Install:
9Plain washer 1
9Impeller 2
NOTE:
Hold the impeller shaft on its width across the
flats awith spanners, etc. and install the
impeller.
3. Install:
9Dowel pin 1
9Gasket (water pump housing cover) 2
4. Install:
9Water pump housing cover 1
9Bolt (water pump housing cover) 2
9Copper washer (coolant drain bolt) 3
9Coolant drain bolt 4
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
1P8-9-32-4c 5/1/06 10:46 AM Page 12

Extent of removal Order Part name Q’ty Remarks
ENGINE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Drain the transmission oil. Refer to “TRANSMISSION OIL
REPLACEMENT” section in the
CHAPTER 3.
Seat and fuel tankRefer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
CarburetorRefer to “CARBURETOR AND REED
VALVE” section.
Exhaust pipe and silencer Refer to “EXHAUST PIPE AND
Exhaust pipe stay (rear) SILENCER” section.
Clutch cable Disconnect at engine side.
Radiator Refer to “RADIATOR” section.
Spark plug
Disconnect the CDI magneto lead.
4-60
ENGINE REMOVALENG
EC4M0000
ENGINE REMOVAL
w
Support the machine securely so there is no dan-
ger of it falling over.



26 Nm (2.6 m•kg, 19 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
75 Nm (7.5 m•kg, 54 ft•lb)
5 Nm (0.5 m•kg, 3.6 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
64 Nm (6.4 m•kg, 46 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
åExcept for USA and CDN
4 Nm (0.4 m•kg, 2.9 ft•lb)
1P8-9-32-4c 5/1/06 10:46 AM Page 22

4-65
CRANKCASE AND CRANKSHAFTENG
EC4N0000
CRANKCASE AND CRANKSHAFT
Extent of removal:1Crankcase separation2Crankshaft removal
3Crankshaft bearing removal
10 Nm (1.0 m•kg, 7.2 ft•lb)30 Nm (3.0 m•kg, 22 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
Extent of removal Order Part name Q’ty Remarks
CRANKCASE AND CRANKSHAFT
REMOVAL
Preparation for Engine Refer to “ENGINE REMOVAL”section.
removal Piston Refer to “
CYLINDER HEAD, CYLINDER
AND PISTON
” section.
Primary drive gear
Kick idle gearRefer to “
KICK AXLE, SHIFT SHAFT AND
Stopper leverPRIMARY DRIVE GEAR”section.
Rotor and stator Refer to “CDI MAGNETO” section.
1 Segment 1 Refer to “REMOVAL POINTS”.
2 Holder 2
Except for USA and CDN
3 Bolt (Neutral switch lead holder) 1
4 Bolt [L=50 mm (1.97 in)] 7
5 Bolt [L=60 mm (2.36 in)] 1
6 Bolt [L=70 mm (2.76 in)] 3
7 Holder 2
8 Crankcase (right) 1 Use special tool.
9 Crankcase (left) 1 Refer to “REMOVAL POINTS”.
10 Crankshaft 1 Use special tool.
Refer to “REMOVAL POINTS”.
11 Oil seal 2
12 Bearing 2 Refer to “REMOVAL POINTS”.




12
3






1P8-9-32-4c 5/1/06 10:46 AM Page 32

4-68
CRANKCASE AND CRANKSHAFTENG
Standard
Runout 0.03 mm 0.05 mm
limit: (0.0012 in) (0.0020 in)
Small end 0.4~1.0 mm 2.0 mm
free play: (0.016~0.039 in) (0.08 in)
Side 0.25~0.75 mm
—
clearance: (0.010~0.030in)
Crank 59.95~60.00 mm
—
width: (2.360~2.362 in)
EC4N4202
Crankshaft
1. Measure:
9Runout limit a
9Small end free play limit b
9Connecting rod big end side clearance c
9Crank width d
Out of specification
Replace.
Use the dial gauge and a thickness gauge.
Dial gauge:
YU-3097/90890-01252
2. Inspect:
9Bearings 1
Rotate inner race with a finger.
Rough spot/Seizure
Replace.
3. Inspect:
9Oil seal 1
Damage
Replace.
1P8-9-32-4c 5/1/06 10:46 AM Page 38

4-69
CRANKCASE AND CRANKSHAFTENG
EC4N5284
Crankshaft
1. Install:
9Crankshaft 1
Use the crankshaft installing tool 2, 3, 4.
Crankshaft installing tool:
Pot 2:
YU-90050/90890-01274
Bolt 3:YU-90050/90890-01275
Adapter 4:YU-90063/90890-01278
å
å
B
åFor USA and CDN
∫Except for USA and CDN
NOTE:
9Hold the connecting rod at top dead center with
one hand while turning the nut of the installing
tool with the other. Operate the installing tool
until the crankshaft bottoms against the bear-
ing.
9Before installing the crankshaft, clean the con-
tacting surface of crankcase.
9Apply the lithium soap base grease on the oil
seal lip.
cC
Do not use a hammer to drive in the crank-
shaft.
EC4N5000
ASSEMBLY AND INSTALLATIONEC4N5300
Crankshaft bearing
1. Install:
9Bearing 1
To crankcase (left and right).
NOTE:
Install the bearing by pressing its outer race
parallel.
EC4N5102
Oil seal
1. Install:
9Oil seal (left) 1
9Oil seal (right) 2
NOTE:
9Apply the lithium soap base grease on the oil
seal lip.
9Install the oil seal with its manufacture’s marks
or numbers facing outward.
1P8-9-32-4c 5/1/06 10:46 AM Page 40

4-70
CRANKCASE AND CRANKSHAFTENG
3. Install:
9O-ring 1
To crankcase (right) 2.
5. Install:
9Dowel pin 1
9Crankcase (right) 2
To crankcase (left) 3.
NOTE:
9Fit the crankcase (right) onto the crankcase
(left). Tap lightly on the case with soft hammer.
9When installing the crankcase, the connecting
rod should be positioned at TDC (top dead
center).
cC
In order to prevent the oil seal lipa a
from
being turned up or damaged, wrap a vinyl
tape or the likeb b
around the right end of
the crankshaft and apply the lithium soap
base grease over the tape.
NOTE:
Clean the contacting surface of crankcase (left
and right) before applying the sealant.
4. Apply:
9Sealant
On the crankcase (right) 1.
Yamaha bond No. 1215
(ThreeBond®No. 1215):
90890-85505
2. Check:
9Shifter operation
9Transmission operation
Unsmooth operation
Repair.
1P8-9-32-4c 5/1/06 10:47 AM Page 42

6. Install:
9Holder (except for USA and CDN) 1
9Bolt [holder (except for USA and CDN)] 2
9Bolt (crankcase)
NOTE:
Tighten the crankcase tightening bolts in stage,
using a crisscross pattern.
4-71
CRANKCASE AND CRANKSHAFTENG
8. Tighten:
9Segment 1
9Bolt (segment) 2
NOTE:
9When installing the segment onto the shift cam
3, align the punch mark awith the dowel pin
b.
9Turn the segment clockwise until it stops and
tighten the bolt.
cC
If the segment gets an impact, it may be
damaged. Take care not to give an impact
to the segment when tightening the bolt.
30 Nm (3.0 m•kg, 22 ft•lb)
7. Install:
9Tension spring 1
9Holder 2
9Bolt (holder) 3
NOTE:
Install the holder so that it contacts the projec-
tion aon the crankcase (right).
10 Nm (1.0 m•kg, 7.2 ft•lb)
9. Remove:
9Sealant
Forced out on the cylinder mating surface.
10. Apply:
9Engine oil
To the crank pin, bearing, oil delivery hole
and connecting rod big end washer.
11. Check:
9Crankshaft and transmission operation
Unsmooth operation
Repair.
14 Nm (1.4 m•kg, 10 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
1P8-9-32-4c 5/1/06 10:47 AM Page 44