ignition YAMAHA YZ250LC 2007 User Guide

EC600000
ELECTRICAL
EC610000
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC611000
ELECTRICAL COMPONENTS
1CDI unit
2“ENGINE STOP” button
3Ignition coil
4TPS (throttle position sensor)
5Solenoid valve
6Neutral switch (Except for USA and CDN)
7CDI magneto
8Spark plug
EC612000
WIRING DIAGRAM
6-1
ELECTRICAL COMPONENTS AND WIRING DIAGRAMELEC
COLOR CODE
B...................Black
L ...................Blue
O ..................Orange
R ..................Red
Sb.................Sky blue
Y...................YellowB/L................Black/Blue
B/R ...............Black/Red
B/W ..............Black/White
G/L ..............Green/Blue
G/W ..............Green/White
W/L...............White/Blue
W/R ..............White/Red
*1:Except for USA and CDN
1P8-9-32-6 4/6/06 3:00 PM Page 2

6-2
IGNITION SYSTEMELEC
EC620000
IGNITION SYSTEM
EC621003
INSPECTION STEPS
Use the following steps for checking the possibility of the malfunctioning engine being attributable to
ignition system failure and for checking the spark plug which will not spark.
*Clean or replace
spark plug.
Primary coil
Secondary coil
Repair or replace.
Spark
Check entire ignition
system for connection.
Spark gap test
No good
No good
No good
No good
No good
No good No Spark
Check “ENGINE STOP”
button.
Pick-up coil
Source coil
Check ignition coil.
Check CDI magneto.
Replace.
Replace.
Replace.
Replace.
Replace.
*marked: Only when the ignition checker is used.
NOTE:
9Remove the following parts before inspection.
1) Seat
2) Fuel tank
9Use the following special tools in this inspection.
Dynamic spark tester:
YM-34487
Ignition checker:
90890-06754Pocket tester:
YU-3112-C/90890-03112
OK
OK
OK
OKReplace.
Check spark plug cap.No good
OK
No good
Replace.
Replace CDI unit
OK
Check neutral switch
(Except for USA and CDN)
1P8-9-32-6 4/6/06 3:00 PM Page 4

6-3
IGNITION SYSTEMELEC
EC622001
SPARK GAP TEST
1. Disconnect the spark plug cap from spark
plug.
2. Connect the dynamic spark tester 1(igni-
tion checker 2) as shown.
9Spark plug cap 3
9Spark plug 4
AFor USA and CDN
BExcept for USA and CDN
3. Kick the kick starter.
4. Check the ignition spark gap.
5. Start engine, and increase spark gap until
misfire occurs. (for USA and CDN only)
EC624000
COUPLERS AND LEADS CONNECTION
INSPECTION
1. Check:
9Couplers and leads connection
Rust/ Dust/ Looseness/Short-circuit 
Repair or replace.
EC625002
“ENGINE STOP” BUTTON INSPECTION
1. Inspect:
9“ENGINE STOP” button conduct
Not continuous while being pushed Replace.
Continuous while being freed Replace.
Minimum spark gap:
6.0 mm (0.24 in)
Tester (+) leadBlack/White lead 1
Tester (–) lead
Black lead 2
B/W B
12
PUSH IN
FREE
Tester selec-
tor position
Ω× 1
å å
B
1P8-9-32-6 4/6/06 3:00 PM Page 8

6-4
IGNITION SYSTEMELEC
EC626003
IGNITION COIL INSPECTION
1. Inspect:
9Primary coil resistance
Out of specification Replace.
2. Inspect:
9Secondary coil resistance
Out of specification Replace.
NOTE:
9Remove the spark plug cap by turning it coun-
terclockwise and inspect.
9Install the spark plug cap by turning it clock-
wise until it is tight.
Tester (+) leadYellow lead 1
Tester (–) lead
Black lead 2
Tester (+) leadSpark plug lead 1
Tester (–) lead
Yellow lead 2
Primary coil Tester selector
resistance position
0.20~0.30Ωat
Ω× 1
20°C (68°F)
Secondary coil Tester selector
resistance position
9.5~14.3kΩat
kΩ× 1
20°C (68°F)
1P8-9-32-6 4/6/06 3:00 PM Page 10

6-5
IGNITION SYSTEMELEC
2. Inspect:
9Source coil 1 resistance
Out of specification Replace.
Tester (+) leadBlack/Red lead 1
Tester (–) lead
Blacklead 2
Source coil 1 Tester selector
resistance position
720~1,080Ωat
Ω× 100
20°C (68°F)
EC62B000
SPARK PLUG CAP INSPECTION
1.Inspect:
9Spark plug cap
Loose connection Tighten.
Deteriorated/Damaged Replace.
9Spark plug cap resistance
Out of specification Replace.
Tester (+) leadSpark plug lead terminal1
Tester (–) lead
Spark plug terminal2
Spark plug cap Tester selector
resistance position
4~6kΩat
kΩ× 1
20°C (68°F)
EC627011
CDI MAGNETO INSPECTION
1. Inspect:
9Pick-up coil resistance
Out of specification Replace.
Tester (+) leadWhite/Red lead 1
Tester (–) lead
White/Blue lead 2
Pick–up coil Tester selector
resistance position
248~372Ωat
Ω× 100
20°C (68°F)
1P8-9-32-6 4/6/06 3:00 PM Page 12

6-6
IGNITION SYSTEMELEC
3. Inspect:
9Source coil 2 resistance
Out of specification Replace.
Tester (+) leadGreen/Blue lead 1
Tester (–) lead
Green/White lead 2
Source coil 2 Tester selector
resistance position
44~66Ωat
Ω× 10
20°C (68°F)
EC628000
CDI UNIT INSPECTION
Check all electrical components. If no fault is
found, replace the CDI unit. Then check the
electrical components again.
NEUTRAL SWITCH INSPECTION
1. Inspect:
9Neutral switch conduct
No continuous while in neutralReplace.
Continuous while in gearReplace.
Tester (+) leadSky blue lead 1
Tester (–) lead
Ground 2
SbGround
12
NEUTRAL
IN GEAR
Tester selec-
tor position
Ω× 1
1P8-9-32-6 4/6/06 3:00 PM Page 14

6-7
SOLENOID VALVE SYSTEMELEC
Check solenoid
valve operation.
Solenoid valve
coil
No good
No good
Check each couplers and
wire connection.
Check solenoid valve.
Repair or replace.
Replace.
Replace.
OK
OK
OKSource coil
No goodReplace.* Check CDI magneto.
Replace CDI unit.
No good
EC650001
SOLENOID VALVE SYSTEM
EC651032
INSPECTION STEPS
If the solenoid valve will not operate, use the following inspection steps.
* marked: Refer to "IGNITION SYSTEM" section.
NOTE:
9Remove the following parts before inspection.
1) Seat
2) Fuel tank
9Use l2V battery in this inspection.
9Use the following special tools in this inspection.
Pocket tester:
YU-3112-C/90890-03112
1P8-9-32-6 4/6/06 3:00 PM Page 16

6-9
TPS (THROTTLE POSITION SENSOR) SYSTEMELEC
Check entire ignition
system for connection.Repair or replace.
OK
OKTPS coil
No goodReplace.Check TPS.
OKSource coil
No goodReplace.*Check CDI magneto.
TPS input
voltageNo goodReplace.Check CDI unit.
No good
EC690000
TPS (THROTTLE POSITION SENSOR) SYSTEM
EC691001
INSPECTION STEPS
If the TPS will not operate, use the following inspection steps.
*marked: Refer to “IGNITION SYSTEM” section.
NOTE:
9Remove the following parts before inspection.
1) Seat
2) Fuel tank
9Use the following special tools in this inspection.
Inductive tachometer:
YU-8036-B
Engine tachometer:
90890-03113Pocket tester:
YU-3112-C/90890-03112
1P8-9-32-6 4/6/06 3:01 PM Page 22