transmission YAMAHA YZ85 2015 User Guide

PERIODIC MAINTENANCE AND ADJUSTMENT
7-3
7
√
5 *Cylinder • Check cylinder for score marks or wear.
Clean.
√
Replace. √
NO. ITEM ROUTINE
After
break-in Every
race Every
third race Every
fifth race As
required
6 *Clutch Check clutch housing, friction plates, clutch plates
and clutch springs for wear or damage.
Adjust. √
√
Replace. √
7 *Transmission Change the transmission oil.
√
Check transmission for damage. √
Replace bearings. √
8 *Shift forks, guide bars,
shift cam
Replace if necessary. Check all parts for wear and damage.
√
9 *Rotor nut
(flywheel
magneto) Tighten.
√√√
10 *Kickstarter system Check idle gear for damage.
√
Replace if necessary.
11 *Exhaust system Check exhaust pipe and muffler for carbon deposits.
√
√
Clean. √
√
√
√
√
12
*Crankshaft Check crankshaft for carbon deposits and damage.
Clean.
U1SN83E0.book Page 3 Monday, September 8, 2014 2:36 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
7-9
7To install the spark plu
g
1. Clean the surface of the spark plug gasket and its mating sur-
face, and then wipe off any grime
from the spark plug threads.
2. Install the spark plug with the spark plug wrench, and then tight-
en it to the specified torque.
TIPIf a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is 1/4–
1/2 turn past finger tight. However, the
spark plug should be tightened to the
specified torque as soon as possible.3. Install the spark plug cap.
EAU41449
Transmission oilThe transmission must be checked for
oil leakage before each ride. If any
leakage is found, have a Yamaha deal-
er check and repair the motorcycle. In
addition, the transmission oil must be
changed at the intervals specified in
the periodic maintenance and lubrica-
tion chart.1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place the motorcycle on a level surface and hold it in an upright
position.
3. Place an oil pan under the trans- mission case to collect the used
oil.
4. Remove the oil filler cap, the trans- mission oil drain bolt and its gas-
ket to drain the oil from the
transmission. 5. Install the drain bolt and its new
gasket, and then tighten the bolt
to the specified torque.
6. Refill with the specified amount of the recommended transmission
oil, and then install and tighten the
oil filler cap.
Tightenin g torque:
Spark plug: 20 Nm (2.0 m·kgf, 14 ft·lbf)
1. Transmission oil filler cap
2. Transmission oil drain bolt
3. GasketTightenin g torque:
Transmission oil drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Recommen ded transmission oil:
See page 9-1.
Oil chan ge quantity:
0.50 L (0.53 US qt, 0.44 Imp.qt)
1
2
3
U1SN83E0.book Page 9 Monday, September 8, 2014 2:36 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
7-10
7
NOTICE
ECA10453
In or der to prevent clutch slip-
pa ge (since the transmission oil
also lu bricates the clutch), do
not mix any chemical additives.
Do not use oils with a d iesel
specification of “CD” or oils of a
hi gher quality than specifie d. In
a ddition, do not use oils lab eled
“ENERGY CONSERVING II” or
hi gher.
 Make sure that no forei gn mate-
rial enters the transmission.7. Start the engine, and then let it idle for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
EAU20071
CoolantThe coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAUM1296
To check the coolant level1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion.TIPThe coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.
 Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.2. Remove the radiator cap and
check the coolant level in the radi-
ator. WARNING! Never attempt
to remove the ra diator cap
when the en gine is hot.
[EWA10382]
TIPThe coolant should be at the bottom of
the radiator filler neck. The level will
change with variation of engine tem-
perature.1. Radiator cap
1. Correct coolant level
1
1
U1SN83E0.book Page 10 Monday, September 8, 2014 2:36 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
7-22
7
EAU51721
Changin g the brake flui dHave a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrica-
tion chart. In addition, have the oil seals
of the master cylinders and calipers as
well as the brake hoses replaced at the
intervals listed below or whenever they
are damaged or leaking.
 Oil seals: Replace every two
years.
 Brake hoses: Replace every four
years.
EAU22762
Drive chain slackThe drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU41413
To check the drive chain slack
1. Install the removable sidestand and place the motorcycle on it.TIPWhen checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.2. Shift the transmission into theneutral position.
3. Measure the drive chain slack as shown. 4. If the drive chain slack is incorrect,
adjust it as follows.
EAU41484
To a djust the drive chain slack
Consult a Yamaha dealer before ad-
justing the drive chain slack. 1. Loosen the axle nut and the lock- nut on each side of the swingarm.
2. To tighten the drive chain, turn the drive chain slack adjusting bolt on
each side of the swingarm in di-
rection (a). To loosen the drive
chain, turn the adjusting bolt on
each side of the swingarm in di-
rection (b), and then push the rear
wheel forward. NOTICE: Improp-
er drive chain slack will over-
Drive chain slack:
35.0–45.0 mm (1.38–1.77 in)
1. Drive chain slack
U1SN83E0.book Page 22 Monday, September 8, 2014 2:36 PM

SPECIFICATIONS
9-1
9
Dimensions:Overall length:YZ85 1821 mm (71.7 in)
YZ85F 1821 mm (71.7 in)
YZ85LW 1899 mm (74.8 in)
YZ85LWF 1899 mm (74.8 in)
Overall width:
758 mm (29.8 in)
Overall height: YZ85 1126 mm (44.3 in)
YZ85F 1126 mm (44.3 in)
YZ85LW 1156 mm (45.5 in)
YZ85LWF 1156 mm (45.5 in)
Seat height: YZ85 841 mm (33.1 in)
YZ85F 841 mm (33.1 in)
YZ85LW 873 mm (34.4 in)
YZ85LWF 873 mm (34.4 in)
Wheelbase:
YZ85 1257 mm (49.5 in)
YZ85F 1257 mm (49.5 in)
YZ85LW 1285 mm (50.6 in)
YZ85LWF 1285 mm (50.6 in)
Ground clearance: YZ85 330 mm (12.99 in)
YZ85F 330 mm (12.99 in)
YZ85LW 360 mm (14.17 in)
YZ85LWF 360 mm (14.17 in)Wei ght:Curb weight:
YZ85 71 kg (157 lb)
YZ85F 71 kg (157 lb)
YZ85LW 73 kg (161 lb)
YZ85LWF 73 kg (161 lb)
Engine:Engine type:
Liquid cooled 2-stroke
Cylinder arrangement:
Single cylinder
Displacement: 85 cm³
Bore × stroke:
47.5 × 47.8 mm (1.87 × 1.88 in)
Compression ratio:
8.1 : 1
Starting system: Kickstarter
Lubrication system: PremixEngine oil:Type:
YAMALUBE 2RTransmission oil:Type:
YAMALUBE 4 (10W-40) or SAE 10W-40
Oil change quantity: 0.50 L (0.53 US qt, 0.44 Imp.qt)Coolant quantity:Radiator (including all routes):
0.54 L (0.57 US qt, 0.48 Imp.qt)Air filter:Air filter element:Wet elementFuel:Recommended fuel:Premium unleaded gasoline only
Fuel tank capacity: 5.0 L (1.32 US gal, 1.10 Imp.gal)
Car buretor:Type × quantity:
PWK28 x 1Spark plu g(s):Manufacturer/model:
NGK/BR10EG
Spark plug gap: 0.5–0.6 mm (0.020–0.024 in)Clutch:Clutch type:Wet, multiple-discTransmission:Primary reduction ratio:
3.611 (65/18)
Final drive: Chain
Secondary reduction ratio: YZ85 3.428 (48/14)
YZ85F 3.428 (48/14)
YZ85LW 3.714 (52/14)
YZ85LWF 3.714 (52/14)
Transmission type:
Constant mesh 6-speed
Operation: Left foot operation
Gear ratio: 1st:2.454 (27/11)
2nd: 1.882 (32/17)
3rd:
1.529 (26/17)
4th: 1.294 (22/17)
U1SN83E0.book Page 1 Monday, September 8, 2014 2:36 PM

11-1
11
INDEX
AAir filter element, cleaning .................... 7-12BBrake and clutch levers, checking and lubricating........................................... 7-24
Brake fluid, changing............................ 7-22
Brake fluid level, checking.................... 7-20
Brake lever.............................................. 4-2
Brake lever free play, checking ............ 7-19
Brake pedal ............................................ 4-3
Brake pedal, checking and lubricating........................................... 7-25CCables, checking and lubricating ......... 7-24
Carburetor, adjusting............................ 7-14
Care ........................................................ 8-1
Clutch lever............................................. 4-1
Clutch lever free play, adjusting ........... 7-18
Coolant ................................................. 7-10DDrive chain, cleaning and lubricating ... 7-23
Drive chain slack .................................. 7-22EEngine break-in ...................................... 6-3
Engine idling speed .............................. 7-14
Engine serial number ............................ 10-1
Engine, starting a warm.......................... 6-1
Engine stop switch ................................. 4-1FFront and rear brake pads, checking ... 7-20
Front fork, adjusting ............................... 4-8
Front fork, bleeding ................................ 4-9
Front fork, checking ............................. 7-26
Fuel ......................................................... 4-3 Fuel cock................................................ 4-6
Fuel tank breather hose ......................... 4-5
Fuel tank cap.......................................... 4-3
HHandlebar switch ................................... 4-1IIdentification numbers ......................... 10-1KKickstarter .............................................. 4-7LLabels, location ...................................... 1-1MMatte color, caution ............................... 8-1
Model label........................................... 10-1PParking ................................................... 6-4
Part locations ......................................... 3-1
Periodic maintenance and lubrication
chart ..................................................... 7-2RRear suspension, lubricating................ 7-25SSafety information .................................. 2-1
Seat ........................................................ 4-7
Shifting ................................................... 6-2
Shift pedal .............................................. 4-2
Shift pedal, checking ........................... 7-19
Shock absorber assembly, adjusting ... 4-10
Sidestand ............................................. 4-12
Spark plug, checking ............................. 7-8
Specifications......................................... 9-1
Starter (choke) knob............................... 4-6
Starting and warming up a cold
engine .................................................. 6-1 Steering, checking ................................ 7-27
Storage ................................................... 8-3
Supporting the motorcycle ................... 7-28
Swingarm pivots, lubricating ................ 7-26
TThrottle grip and cable, checking and
lubricating ........................................... 7-24
Throttle grip free play, adjusting ........... 7-15
Tires ...................................................... 7-15
Transmission oil ...................................... 7-9
Troubleshooting .................................... 7-31
Troubleshooting charts ......................... 7-32VVehicle identification number ............... 10-1WWheel bearings, checking .................... 7-27
Wheel (front).......................................... 7-28
Wheel (rear)........................................... 7-29
Wheels .................................................. 7-17
U1SN83E0.book Page 1 Monday, September 8, 2014 2:36 PM