set clock YAMAHA YZF-R1 2009 Owners Manual

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3
EAU47612
Multi-function meter unit
WARNING
EWA12422
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changingsettings while riding can distract the
operator and increase the risk of an
accident.
The multi-function meter unit is
equipped with the following:

a speedometer


a tachometer


an odometer


two tripmeters (which show the
distance traveled since they were
last set to zero)


a fuel reserve tripmeter (which
shows the distance traveled since
the fuel level warning light came
on)


a stopwatch


a clock


a coolant temperature display


an air intake temperature display


a transmission gear display


a drive mode display (which shows
the selected drive mode)


a throttle opening position display


a fuel consumption display (instan-
taneous and average consumption
functions)


a self-diagnosis device


a display brightness, shift timing
indicator light and throttle opening
position display control mode
TIP

Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons.


For the U.K. only: To switch the
speedometer and odometer/trip-
meter/fuel consumption displays
between kilometers and miles,
press the “SELECT” button for atleast one second.
Tachometer
1.“RESET” button
2.“SELECT” button
3. Tachometer
4. Shift timing indicator light
5. Throttle opening position display
6. Coolant temperature display/air intake tem-
perature display
7. Mode display
8. Speedometer
9. Odometer/tripmeter/fuel reserve tripmeter/in-
stantaneous fuel consumption/average fuel
consumption
10.Clock/stopwatch
11.Transmission gear display2
134
5
6
7
8
9
10 11
1. Tachometer
2. Tachometer red zone
2 1
U14BE0E0.book Page 9 Friday, November 21, 2008 9:23 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-10
3The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the ta-
chometer needle sweeps once across
the r/min range and then returns to zero
r/min in order to test the electrical cir-
cuit.
NOTICE
ECA10031
Do not operate the engine in the ta-
chometer red zone.Red zone: 13750 r/min and above
Clock and stopwatch modesTo set the clock
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and
the minute digits start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
To display the stopwatchTo change the display to the stopwatch
mode, push the “SELECT” button and
“RESET” button together. To change
the display back to the clock mode,
push the “SELECT” button and “RE-
SET” button together; however, this is
not possible when the stopwatch is
counting.
Standard measurement1. Push the “RESET” button to start
the stopwatch.
2. Push the “SELECT” button to stop
the stopwatch.3. Push the “SELECT” button again
to reset the stopwatch.
Split time measurement
1. Push the “RESET” button to start
the stopwatch.
2. Push the “RESET” button or start
switch“” to measure split times.
Split times are displayed on the
odometer display for five seconds.
3. Push the “RESET” button or start
switch“” to display the final split
time or push the “SELECT” button
to stop the stopwatch and display
the total elapsed time.
Split time history
1. Clock/stopwatch
1
1. Coolant temperature display/air intake tem-
perature display
2. Stopwatch
21
U14BE0E0.book Page 10 Friday, November 21, 2008 9:23 AM