coolant YAMAHA YZF-R1S 2004 User Guide

2-42
R Arrange so as not for each hose
to cross in the part between “BB”
from the section “AA” which is in
the illustration.G Route the lead by the inside of
the water hose and water pipe.
H Route the lead by the inside of
the water hose and water pipe.
I Route by the outside of vehicle
away from the water hose.
J Point the tip of the clamp (exces-
sive part) to the down rear side of
the vehicle. Fasten the wire har-
ness with a clamp.
K Route the water hose so that it is
placed at the outermost position
finally after routing other leads
and hoses in the guide.
L To the coolant reservoir tank
CABLE ROUTINGSPEC
M There should be no exposure of
bared conductors due to the dis-
placement of the tube.
N Route the coolant reservoir tank
drain hose so that it is routed at
the innermost position to each
hose and lead.
O Can be routed in any order.
P Align the molded part of the fuel
tank drain hose with the stay 1.
Q Routing of the fuel tank drain
hose.
EXUP servo motor, oil level
switch and sidestand switch
leads are omitted in this drawing.
ProCarManuals.com

2-43
33Throttle body side cap
34Mud guard
35Turn signal light lead
36License plate light lead
37Rear fender rib
38Speed sensor lead
39Rear brake light switch lead
40Rear frame
41Swingarm bracket
42Main fuse lead
43Starting circuit cut-off relay lead
44Turn signal light relay lead
45Starter relay lead
46Main fuse lead (To the battery
positive lead)
47Right handlebar switch lead
17Battery negative lead
18Starter motor lead
19A.C.magneto lead
20Oil level switch lead
21Sidestand switch lead
22Throttle body lead
23Coolant reservoir tank drain hose
24Fuel tank drain hose
25Cover 7
26Radiator fan motor lead (left)
27Radiator fan motor lead (right)
28Wire harness
29Pipe 3
30Frame
31Coolant reservoir tank hose
32Thermo stat assembly breather
hose
CABLE ROUTINGSPEC
1Heat protector
2Crankshaft position sensor lead
3Neutral switch lead
4Ground lead
5Coolant reservoir tank
6Battery positive lead
7Starter relay
8Turn signal relay
9Main fuse
10Lean angle cut-off switch
11Atmospheric pressure sensor
12Tail / brake light lead
13Rear fender
14Seat lock cable
15Anti safety alarm coupler
16Starting circuit cut-off relay
ProCarManuals.com

3-37
ADJUSTING THE EXUP CABLES /
CHECKING THE COOLANT LEVELCHK
ADJ
NOTE:
CAUTION:
NOTE: 7. Install:

bottom cowlings
Refer to “COWLINGS”.
EAS00102
CHECKING THE COOLANT LEVEL
1. Stand the motorcycle on a level surface.

Place the motorcycle on a suitable stand.

Make sure the motorcycle is upright.
2. Check:

coolant level
The coolant level should be between the
maximum level mark
a and minimum level
mark
b.
Below the minimum level mark
Add the
recommended coolant to the proper level.

Adding water instead of coolant lowers the
antifreeze content of the coolant. If water is
used instead of coolant check, and if nec-
essary, correct the antifreeze concentra-
tion of the coolant.

Use only distilled water. However, if dis-
tilled water is not available, soft water may
be used.
3. Start the engine, warm it up for several min-
utes, and then turn it off.
4. Check:

coolant level
Before checking the coolant level, wait a few
minutes until it settles.
ProCarManuals.com

3-39
CHANGING THE COOLANT
CHK
ADJ
CAUTION:
EAS00105
CHANGING THE COOLANT
1. Remove:

bottom cowlings

side cowlings
Refer to “COWLINGS”.

rider seat
Refer to “SEATS”.
2. Remove:

coolant reservoir tank

coolant reservoir hose
3. Disconnect:

coolant reservoir cap
1
4. Drain:

coolant
(from the coolant reservoir tank)
5. Remove:

radiator cap
1
A hot radiator is under pressure. Therefore,
do not remove the radiator cap when the en-
gine is hot. Scalding hot fluid and steam may
be blown out, which could cause serious in-
jury. When the engine has cooled, open the
radiator cap as follows:
Place a thick rag or a towel over the radiator
cap and slowly turn the radiator cap coun-
terclockwise toward the detent to allow any
residual pressure to escape. When the his-
sing sound has stopped, press down on the
radiator cap and turn it counterclockwise to
remove.
The following procedure applies to all of the
coolant drain bolts and copper washers.
6. Remove:

coolant drain bolts
1
(along with the copper washers)
ProCarManuals.com

3-40
CHANGING THE COOLANT
CHK
ADJ
10 Nm (1.0 m
kg, 7.2 ft
lb)
WARNING
7. Drain:

coolant
(water pump inlet pipe and outlet pipe)
8. Check:

copper washers
1 New
9. Install:

coolant drain bolts
2
(with copper washers)
10. Install:

coolant reservoir tank
11. Connect:

coolant reservoir hose
12. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Recommended antifreeze
High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Mixing ratio
1:1 (antifreeze:water)
Quantity
Total amount
2.51 L
(2.21 Imp qt, 2.65 US qt)
Coolant reservoir capacity
0.25 L
(0.22 Imp qt, 0.26 US qt)
Handling notes for coolant
Coolant is potentially harmful and should be
handled with special care.

If coolant splashes in your eyes, thorough-
ly wash them with water and consult a doc-
tor.

If coolant splashes on your clothes, quick-
ly wash it away with water and then with
soap and water.

If coolant is swallowed, induce vomiting
and get immediate medical attention.
ProCarManuals.com

3-41
CHANGING THE COOLANT
CHK
ADJ
CAUTION:
NOTE:
Adding water instead of coolant lowers the
antifreeze content of the coolant. If water is
used instead of coolant check, and if nec-
essary, correct the antifreeze concentra-
tion of the coolant.

Use only distilled water. However, if dis-
tilled water is not available, soft water may
be used.

If coolant comes into contact with painted
surfaces, immediately wash them with wa-
ter.

Do not mix different types of antifreeze.
13. Install:

radiator cap
14. Fill:

coolant reservoir tank
(with the recommended coolant to the maxi-
mum level mark
a)
15. Install:

coolant reservoir cap
16. Start the engine, warm it up for several min-
utes, and then stop it.
17. Check:

coolant level
Refer to “CHECKING THE COOLANT LEV-
EL”.
Before checking the coolant level, wait a few
minutes until the coolant has settled.
18. Install:

rider seat
Refer to “SEATS”.

bottom cowlings

side cowlings
Refer to “COWLINGS”.
ProCarManuals.com

5-22
Order Job / Part Q’ty Remarks
1
2
3
4
5
6Removing the cylinder head
Engine
Intake camshaft
Exhaust camshaft
Cylinder head
Cylinder head gasket
Dowel pin
Coolant pipe
O-ring
Thermo wax out let hose1
1
2
1
1
1Remove the parts in the order listed.
Refer to “ENGINE”.
Refer to “CAMSHAFTS”.
For installation, reverse the removal
procedure.
18 Nm (1.8 m
kg, 13 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
19 Nm (1.9 m
kg, 14 ft
lb)
67 Nm (6.7 m
kg, 48 ft
lb)
1st
2nd
10 Nm (1.0 m
kg, 7.2 ft
lb)
CYLINDER HEADENG
EAS00221
CYLINDER HEAD
ProCarManuals.com

6-1
Order Job / Part Q’ty Remarks
1
2
3
4
5Removing the radiator
Rider seat
Fuel tank
Air filter case
Side cowlings
Bottom cowling
Coolant
Fuse box stay
Coolant reservoir hose
Radiator
Radiator fan motor
Radiator inlet hose1
1
1
2
1Remove the parts in the order listed.
Refer to “AIR FILTER CASE” in chapter 3.
Drain.
Refer to “CHANGING THE COOLANT” in
chapter 3.
Disconnect.
Refer to “COWLINGS” in chapter 3.
Refer to “SEATS” in chapter 3.
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
5 Nm (0.5 m
kg, 3.6 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
RADIATORCOOL
EAS00454
COOLING SYSTEM
RADIATOR
ProCarManuals.com

6-4
RADIATORCOOL
EAS00456
INSTALLING THE RADIATOR
1. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” in
chapter 3.
2. Check:

cooling system
Leaks
Repair or replace any faulty part.
3. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Refer to “CHECKING THE RADIATOR”.
ProCarManuals.com

6-7
OIL COOLERCOOL
63 Nm (6.3 m
kg, 46 ft
lb)
NOTE:
EAS00458
CHECKING THE OIL COOLER
1. Check:

oil cooler
Cracks / damage
Replace.
2. Check:

oil cooler inlet hose

oil cooler outlet hose
Cracks / damage / wear
Replace.
EAS00459
INSTALLING THE OIL COOLER
1. Clean:

mating surfaces of the oil cooler and the
crankcase
(with a cloth dampened with lacquer thinner)
2. Install:

O-ring
New

oil cooler
1

washer 2 New

bolt
3

Before installing the oil cooler, lubricate the oil
cooler bolt and O-ring with a thin coat of engine
oil.

Make sure that the O-ring is positioned proper-
ly.

Align the projection
a on the oil cooler with the
slot
b in the crankcase.
3. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” in
chapter 3.

crankcase
(with the specified amount of the recom-
mended engine oil)
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Check:

cooling system
Leaks
Repair or replace any faulty part.
5. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Refer to “CHECKING THE RADIATOR”.
ProCarManuals.com