lock YAMAHA YZF-R1S 2004 Owner's Manual

3-43
ADJUSTING THE REAR BRAKE
CHK
ADJ
a
b
WARNING
WARNING
CAUTION:
EAS00110
ADJUSTING THE REAR BRAKE
1. Adjust:

brake pedal position
a. Loosen the locknut
1.
b. Turn the adjusting bolt
2 in direction a or b
until the specified brake pedal position is ob-
tained.
Direction
Brake pedal is raised.
DirectionBrake pedal is lowered.
After adjusting the brake pedal position,
check that the end of the adjusting bolt
c is
visible through the hole
d.
c. Tighten the locknut
1 to specification.
Locknut
16 Nm (1.6 m
kg, 12 ft
lb)
A soft or spongy feeling in the brake pedal
can indicate the presence of air in the brake
system. Before the vehicle is operated, the
air must be removed by bleeding the brake
system. Air in the brake system will consid-
erably reduce braking performance and
could result in loss of control and possibly
an accident. Therefore, check and, if neces-
sary, bleed the brake system.
After adjusting the brake pedal position,
make sure there is no brake drag.
2. Adjust:

rear brake light switch
Refer to “ADJUSTING THE REAR BRAKE
LIGHT SWITCH”.
ProCarManuals.com

3-44
A
B
CHECKING THE BRAKE FLUID LEVEL
CHK
ADJ
NOTE:
WARNING
CAUTION:
NOTE:
EAS00115
CHECKING THE BRAKE FLUID LEVEL
1. Stand the motorcycle on a level surface.

Place the motorcycle on a suitable stand.

Make sure the motorcycle is upright.
2. Check:

brake fluid level
Below the minimum level mark
a
Add the
recommended brake fluid to the proper level.
Recommended brake fluid
DOT 4
AFront brake
BRear brake

Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

Refill with the same type of brake fluid that
is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
In order to ensure a correct reading of the brake
fluid level, make sure the top of the brake fluid
reservoir is horizontal.
ProCarManuals.com

3-48
BLEEDING THE HYDRAULIC BRAKE SYSTEM /
ADJUSTING THE SHIFT PEDALCHK
ADJ
NOTE:
WARNING
NOTE:
a
b
Loosening the bleed screw will release the pres-
sure and cause the brake lever to contact the
throttle grip or the brake pedal to fully extend.
h. Tighten the bleed screw and then release the
brake lever or brake pedal.
i. Repeat steps (e) to (h) until all of the air
bubbles have disappeared from the brake
fluid in the plastic hose.
j. Tighten the bleed screw to specification.
Bleed screw
6 Nm (0.6 m
kg, 4.3 ft
lb)
k. Fill the brake fluid reservoir to the proper lev-
el with the recommended brake fluid.
Refer to “CHECKING THE BRAKE FLUID
LEVEL”.
After bleeding the hydraulic brake system,
check the brake operation.
After bleeding air, the brake fluid may ooze
around the thread section of each bleed screw.
This phenomenon does not show the leakage
but the brake fluid that has been accumulated in
the thread of screw while bleeding air. Please
wipe off to make the parts clean.
EAS00136
ADJUSTING THE SHIFT PEDAL
1. Adjust:

shift pedal position
a. Loosen both locknuts
1.
b. Turn the shift rod
2 in direction a or b to
obtain the correct shift pedal position.
Direction
Shift pedal is raised.
DirectionShift pedal is lowered.
c. Tighten both locknuts.
ProCarManuals.com

3-49
ADJUSTING THE DRIVE CHAIN SLACK
CHK
ADJ
NOTE:
CAUTION:
WARNING
NOTE:
EAS00140
ADJUSTING THE DRIVE CHAIN SLACK
The drive chain slack must be checked at the
tightest point on the chain.
A drive chain that is too tight will overload
the engine and other vital parts, and one that
is too loose can skip and damage the swin-
garm or cause an accident. Therefore, keep
the drive chain slack within the specified
limits.
1. Stand the motorcycle on a level surface.
Securely support the motorcycle so that
there is no danger of it falling over.
Place the motorcycle on a suitable stand so that
the rear wheel is elevated.
2. Spin the rear wheel several times and find
the tightest position of drive chain.
3. Check:

drive chain slack
a
Out of specification
Adjust.
Drive chain slack
25
35 mm (0.98
1.38 in)
4. Adjust:

drive chain slack
a. Loosen the wheel axle nut
1.
b. Loosen both locknuts
2.
c. Turn both adjusting bolts
3 in direction a or
b until the specified drive chain slack is ob-
tained.
ProCarManuals.com

3-50
a
b
ADJUSTING THE DRIVE CHAIN SLACK /
LUBRICATING THE DRIVE CHAINCHK
ADJ
NOTE:
DirectionDrive chain is tightened.
DirectionDrive chain is loosened.
To maintain the proper wheel alignment, adjust
both sides evenly.
d. Tighten both locknuts to specification.
Locknut
16 Nm (1.6 m
kg, 12 ft
lb)
e. Tighten the wheel axle nut to specification.
Wheel axle nut
150 Nm (15 m
kg, 108 ft
lb)
EAS00142
LUBRICATING THE DRIVE CHAIN
The drive chain consists of many interacting
parts. If the drive chain is not maintained proper-
ly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
motorcycle is used in dusty areas.
This motorcycle has a drive chain with small
rubber O-rings between each side plate. Steam
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only kero-
sene to clean the drive chain. Wipe the drive
chain dry and thoroughly lubricate it with engine
oil or chain lubricant that is suitable for O-ring
chains. Do not use any other lubricants on the
drive chain since they may contain solvents that
could damage the O-rings.
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
ProCarManuals.com

3-51
CHECKING AND ADJUSTING THE STEERING HEAD
CHK
ADJ
WARNING
NOTE:
NOTE:
EAS00146
CHECKING AND ADJUSTING THE
STEERING HEAD
1. Stand the motorcycle on a level surface.
Securely support the motorcycle so that
there is no danger of it falling over.
Place the motorcycle on a suitable stand so that
the front wheel is elevated.
2. Check:

steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding / looseness
Adjust the steering
head.
3. Remove:

upper bracket
Refer to “HANDLEBAR” and “STEERING
HEAD” in chapter 4.
4. Adjust:

steering head
a. Remove the lock washer
1, the upper ring
nut
2, and the rubber washer 3.
b. Loosen the lower ring nut
4 and then tighten
it to specification with a steering nut wrench
5.
Set the torque wrench at a right angle to the
steering nut wrench.
Steering nut wrench
90890-01403, YU-33975
Lower ring nut (initial tightening
torque)
52 Nm (5.2 m
kg, 38 ft
lb)
ProCarManuals.com

3-52
CHECKING AND ADJUSTING THE STEERING HEAD
CHK
ADJ
WARNING
NOTE:
NOTE: c. Loosen the lower ring nut
4 completely, then
tighten it to specification.
Do not overtighten the lower ring nut.
Lower ring nut
(final tightening torque)
18 Nm (1.8 m
kg, 13 ft
lb)
d. Check the steering head for looseness or
binding by turning the front fork all the way in
both directions. If any binding is felt, remove
the under bracket and check the upper and
lower bearings.
Refer to “STEERING HEAD” in chapter 4.
e. Install the rubber washer
3.
f. Install the upper ring nut
2.
g. Finger tighten the upper ring nut
2, then
align the slots of both ring nuts. If necessary,
hold the lower ring nut and tighten the upper
ring nut until their slots are aligned.
h. Install the lock washer
1.
Make sure the lock washer tabs
a sit correctly
in the ring nut slots
b.
5. Install:

upper bracket
Refer to “HANDLEBAR” and “STEERING
HEAD” in chapter 4.
6. Measure:

steering head tension
Make sure all of the cables and wires are prop-
erly routed.
a. Point the front wheel straight ahead.
b. Install a plastic locking tie
1 loosely around
the end of the handlebar as shown.
c. Hook a spring gauge
2 onto the plastic lock-
ing tie.
d. Hold the spring gauge at a 90 angle from the
handlebar, pull the spring gauge, and then
record the measurement when the handle-
bar starts to run.
ProCarManuals.com

3-68
CHECKING THE FUSES
CHK
ADJ
WARNING
Pocket tester
90890-03112, YU-3112
b. If the pocket tester indicates “∞”, replace the
fuse.
3. Replace:

blown fuse
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct amperage
rating.
c. Set on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check
the electrical circuit.
Fuses
Amperage
ratingQ’ty
Main50 A1
Fuel injection
system15 A1
Headlight25 A1
Signaling
system10 A1
Ignition15 A1
Backup fuse
(odometer
and clock)
10 A1
Radiator
fan motor15 A2
Reserve25 A, 15 A,
10 A1
Never use a fuse with an amperage rating
other than that specified. Improvising or us-
ing a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.
4. Install:

front cowling inner panel (left)
Refer to “COWLINGS”.

rider seat
Refer to “SEATS”.
ProCarManuals.com

4-9
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9
10Removing the rear wheel
Rear brake caliper
Lock nut (left and right)
Adjusting bolt (left and right)
Wheel axle nut
Washer
Rear wheel axle
Left adjusting block
Right adjusting block
Rear wheel
Brake caliper bracket1
2
2
1
1
1
1
1
1
1Remove the parts in the order listed.
Place the motorcycle on a suitable stand
so that the rear wheel is elevated.
Loosen.
Loosen.
For installation, reverse the removal
procedure.
NOTE:
22 Nm (2.2 m
kg, 16 ft
lb)
27 Nm (2.7 m
kg, 20 ft
lb)
150 Nm (15 m
kg, 108 ft
lb)
REAR WHEEL AND BRAKE DISCCHAS
EAS00551
REAR WHEEL AND BRAKE DISC
REAR WHEEL
ProCarManuals.com

4-12
REAR WHEEL AND BRAKE DISCCHAS
WARNING
NOTE:
NOTE:
NOTE:
EAS00561
REMOVING THE REAR WHEEL
1. Stand the motorcycle on a level surface.
Securely support the motorcycle so that
there is no danger of it falling over.
Place the motorcycle on a suitable stand so that
the rear wheel is elevated.
2. Remove:

brake caliper
1
Do not depress the brake pedal when removing
the brake caliper.
3. Loosen:

locknut
1

adjusting bolt 2
4. Remove:

wheel axle nut
1

wheel axle

rear wheel
Push the rear wheel forward and remove the
drive chain from the rear wheel sprocket.
5. Remove:

left collar
1

rear wheel drive hub 2

rear wheel drive hub damper

right collar
ProCarManuals.com