oil YAMAHA YZF-R1S 2004 Repair Manual

4-13
REAR WHEEL AND BRAKE DISCCHAS
EAS00565
CHECKING THE REAR WHEEL
1. Check:

wheel axle

rear wheel

wheel bearings

oil seals
Refer to “CHECKING THE FRONT
WHEEL”.
2. Check:

tire

rear wheel
Damage / wear
Replace.
Refer to “CHECKING THE TIRES” and
“CHECKING THE WHEELS” in chapter 3.
3. Measure:

radial wheel runout

lateral wheel runout
Refer to “CHECKING THE FRONT
WHEEL”.
EAS00567
CHECKING THE REAR WHEEL DRIVE HUB
1. Check:

rear wheel drive hub
1
Cracks / damage
Replace.

rear wheel drive hub dampers
2
Damage / wear
Replace.
EAS00568
CHECKING AND REPLACING THE REAR
WHEEL SPROCKET
1. Check:

rear wheel sprocket
More than 1 / 4 tooth
a wear
Replace the
rear wheel sprocket.
Bent teeth
Replace the rear wheel sprock-
et.
bCorrect
1Drive chain roller
2Rear wheel sprocket
ProCarManuals.com

4-14
REAR WHEEL AND BRAKE DISCCHAS
NOTE:
150 Nm (15 m
kg, 108 ft
lb)
27 Nm (2.7 m
kg, 20 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
NOTE: 2. Replace:

rear wheel sprocket
a. Remove the self-locking nuts and the rear
wheel sprocket.
b. Clean the rear wheel drive hub with a clean
cloth, especially the surfaces that contact the
sprocket.
c. Install the new rear wheel sprocket.
Rear wheel sprocket self-locking
nut
100 Nm (10 m
kg, 72 ft
lb)
Tighten the self-locking nuts in stages and in a
crisscross pattern.
EAS00572
INSTALLING THE REAR WHEEL
1. Lubricate:

wheel axle

wheel bearings

oil seal lips
Recommended lubricant
Lithium-soap-based grease
2. Tighten:

wheel axle nut

brake caliper bolts (front)
(rear)
EAS00575
ADJUSTING THE REAR WHEEL STATIC
BALANCE

After replacing the tire, wheel or both, the rear
wheel static balance should be adjusted.

Adjust the rear wheel static balance with the
brake disc and rear wheel drive hub installed.
1. Adjust:

rear wheel static balance
Refer to “ADJUSTING THE FRONT WHEEL
STATIC BALANCE”.
ProCarManuals.com

4-30
FRONT AND REAR BRAKESCHAS
NOTE:
WARNING
CAUTION:

While holding the brake hose, tighten the
union bolt.

Turn the handlebars to the left and right to
make sure the brake hose does not touch oth-
er parts (e.g., wire harness, cables, leads).
Correct if necessary.
4. Fill:

brake fluid reservoir
(with the specified amount of the recom-
mended brake fluid)
Recommended brake fluid
DOT 4

Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

Refill with the same type of brake fluid that
is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
5. Bleed:

brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
ProCarManuals.com

4-32
FRONT AND REAR BRAKESCHAS
WARNING
CAUTION:

Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

Refill with the same type of brake fluid that
is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
4. Bleed:

brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
5. Check:

brake fluid level
Below the minimum level mark
a
Add the
recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” in chapter 3.
6. Adjust:

rear brake light operation timing
Refer to “ADJUSTING THE REAR BRAKE
LIGHT SWITCH” in chapter 3.
ProCarManuals.com

4-41
FRONT AND REAR BRAKESCHAS
WARNING
CAUTION:
3. Fill:

brake fluid reservoir
(with the specified amount of the recom-
mended brake fluid)
Recommended brake fluid
DOT 4

Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

Refill with the same type of brake fluid that
is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
4. Bleed:

brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM“ in chapter 3.
5. Check:

brake fluid level
Below the minimum level mark
a
Add the
recommended brake fluid to the proper level.
Refer to ”CHECKING THE BRAKE FLUID
LEVEL“ in chapter 3.
6. Check:

brake lever operation
Soft or spongy feeling
Bleed the brake
system.
Refer to ”BLEEDING THE HYDRAULIC
BRAKE SYSTEM“ in chapter 3.
ProCarManuals.com

4-43
FRONT AND REAR BRAKESCHAS
WARNING
CAUTION:
2. Fill:

brake fluid reservoir
(with the specified amount of the recom-
mended brake fluid)
Recommended brake fluid
DOT 4

Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

Refill with the same type of brake fluid that
is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.
Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.
3. Bleed:

brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
4. Check:

brake fluid level
Below the minimum level mark
a
Add the
recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” in chapter 3.
5. Check:

brake pedal operation
Soft or spongy feeling
Bleed the brake
system.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.
ProCarManuals.com

4-45
FRONT FORKCHAS
Order Job / Part Q’ty Remarks
Disassembling the front fork legs
Cap bolt
O-ring
Damper adjusting rod
Nut
Washer
Spacer
Fork spring
Dust seal
Oil seal clip
Oil seal1
1
1
1
1
1
1
1
1
1Disassemble the parts in the order listed.
The following the procedure applies to
both of the front fork legs.
NOTE:
1
2
3
4
5
6
7
8
9
10
23 Nm (2.3 m
kg, 17 ft
lb)
15 Nm (1.5 m
kg, 11 ft
lb)
23 Nm (2.3 m
kg, 17 ft
lb)
EAS00648
ProCarManuals.com

4-48
FRONT FORKCHAS
NOTE:
WARNING
NOTE:
CAUTION:
EAS00652
DISASSEMBLING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
1. Remove:

cap bolt
1
(from the damper adjusting rod)

spacer
2

nut 3
a. Press down on the spacer with the fork
spring compressor
4.
b. Install the rod holder
5 between the nut 3
and the spacer 2.
Fork spring compressor
90890-01441, YM-01441
Rod holder
90890-01434, YM-01434
Use the side of the rod holder that is marked “B”.
c. Loosen the nut.
d. Remove the cap bolt.
e. Remove the rod holder and fork spring com-
pressor.
The fork spring is compressed.
f. Remove the spacer and nut.
2. Drain:

fork oil
Stroke the damper rod
1 several times while
draining the fork oil.
3. Remove:

dust seal

oil seal clip
1

oil seal

washer
(with a flat-head screwdriver)
Do not scratch the inner tube.
ProCarManuals.com

4-49
FRONT FORKCHAS
NOTE:
WARNING
4. Remove:

damper rod assembly bolt

damper rod assembly
While holding the damper rod assembly with the
damper rod holder
1, loosen the damper rod
assembly bolt.
Damper rod holder
90890-01423, YM-01423
EAS00656
CHECKING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
1. Check:

inner tube
1

outer tube 2
Bends / damage / scratches
Replace.
Do not attempt to straighten a bent inner
tube as this may dangerously weaken it.
2. Measure:

spring free length
a
Out of specification
Replace.
Spring free length
236.5 mm (9.31 in)
: 231.8 mm (9.13 in)
3. Check:

damper rod
1
Damage / wear
Replace.
Obstruction
Blow out all of the oil pas-
sages with compressed air.

damper rod adjusting rod
Bends / damage
Replace.
ProCarManuals.com

4-50
FRONT FORKCHAS
CAUTION:
WARNING
NOTE:
The front fork leg has a built-in damper ad-
justing rod and a very sophisticated inter-
nal construction, which are particularly
sensitive to foreign material.

When disassembling and assembling the
front fork leg, do not allow any foreign ma-
terial to enter the front fork.
4. Check:

cap bolt O-ring
1
Damage / wear
Replace.
EAS00659
ASSEMBLING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.

Make sure the oil levels in both front fork
legs are equal.

Uneven oil levels can result in poor han-
dling and a loss of stability.

When assembling the front fork leg, be sure to
replace the following parts:
– outer tube bushing
– oil seal
– dust seal
– Before assembling the front fork leg, make
sure all of the components are clean.
1. Install:

inner tube
1

damper rod assembly 2

damper rod assembly bolt

copper washer
New
ProCarManuals.com