oil filter YAMAHA YZF-R1SC 2004 Service Manual

LUBRICATION DIAGRAMS2-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CABLE ROUTING2-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 3
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PERIODIC MAINTENANCE CHART FOR THE EMISSION
CONTROL SYSTEM3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL MAINTENANCE AND LUBRICATION CHART3-1 . . . . . . . . .
SEATS3-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL TANK3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FUEL TANK 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FUEL PUMP 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FUEL PUMP 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FUEL TANK 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COWLINGS3-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT COWLING AND SIDE COWLINGS 3-7. . . . . . . . . . . . . . . . . . .
REAR COWLING 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR FILTER CASE3-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE3-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE VALVE CLEARANCE 3-11. . . . . . . . . . . . . . . . . . . . . .
SYNCHRONIZING THE THROTTLE BODIES 3-17. . . . . . . . . . . . . . . . .
ADJUSTING THE EXHAUST GAS VOLUME 3-19. . . . . . . . . . . . . . . . . .
ADJUSTING THE ENGINE IDLING SPEED 3-21. . . . . . . . . . . . . . . . . . .
ADJUSTING THE THROTTLE CABLE FREE PLAY 3-22. . . . . . . . . . . .
CHECKING THE SPARK PLUGS 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEASURING THE COMPRESSION PRESSURE 3-24. . . . . . . . . . . . . .
CHECKING THE ENGINE OIL LEVEL 3-26. . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE ENGINE OIL 3-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEASURING THE ENGINE OIL PRESSURE 3-29. . . . . . . . . . . . . . . . .
ADJUSTING THE CLUTCH CABLE FREE PLAY 3-31. . . . . . . . . . . . . . .
REPLACING THE AIR FILTER ELEMENT 3-32. . . . . . . . . . . . . . . . . . . .
CHECKING THE FUEL AND BREATHER HOSES 3-33. . . . . . . . . . . . .
CHECKING THE CRANKCASE BREATHER HOSE 3-34. . . . . . . . . . . .
CHECKING THE EXHAUST SYSTEM 3-35. . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE EXUP CABLES 3-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE COOLANT LEVEL 3-37. . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE COOLING SYSTEM 3-38. . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE COOLANT 3-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com

1-9
SPECIAL TOOLS
GEN
INFO
NOTE:
EAS00027
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly. Use only
the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools
or improvised techniques. Special tools, part numbers or both may differ depending on the country.
When placing an order, refer to the list provided below to avoid any mistakes.

For U.S.A. and Canada, use part number starting with “YM-”, “YU-”, or “ACC-”.

For others, use part number starting with “90890-”.
Tool No.
Tool name / FunctionIllustration
90890-01304
YU-01304
Piston pin puller
This tool is used to remove the piston pins.
Radiator cap tester
90890-01325
YU-24460-01
Adapter
90890-01352
YU-33984Radiator cap tester
Radiator cap tester adapter
These tools are used to check the cooling
system.
90890-01403
YU-33975
Steering nut wrench
This tool is used to loosen or tighten the
steering stem ring nuts.
90890-01423
YM-01423
Damper rod holder
This tool is used to hold the damper rod as-
sembly when loosening or tightening the
damper rod assembly bolt.
90890-01426
YU-38411
Oil filter wrench
This tool is needed to loosen or tighten the
oil filter cartridge.
90890-01434
YM-01434
Rod holder
This tool is used to support the damper ad-
justing rod.
Rod puller
90890-01437
YM-01437
Rod puller
attachment
90890-01436
YM-01436Rod puller
Rod puller attachment
These tools are used to pull up the front
fork damper rod.
ProCarManuals.com

2-2
ENGINE SPECIFICATIONSSPEC
2
ENGINE SPECIFICATIONS
ItemStandardLimit
Engine
Engine type
Displacement
Cylinder arrangement
Bore
stroke
Compression ratio
Engine idling speed
Vacuum pressure at engine idling
speed
Standard compression pressure
(at sea level)
Liquid-cooled, 4-stroke, DOHC
998 cm3 (60.90 cu.in)
Forward-inclined parallel 4-cylinder
77.0
53.6 mm (3.03
2.11 in)
12.4 : 1
1,150  1,250 r / min
22 kPa (165 mmHg, 6.5 inHg)
1,480 kPa (14.80 kg / cm
2,14.80 bar,
210.5 psi) at 350 r / min
































Fuel
Recommended fuel
Fuel tank capacity
Total (including reserve)
Reserve only
Premium unleaded gasoline only
18 L (3.96 Imp gal, 4.76 US gal)
3.4 L (0.75 Imp gal, 0.90 US gal)











Engine oil
Lubrication system
Recommended oil
Quantity
Total amount
Without oil filter cartridge
replacement
With oil filter cartridge replacement
Oil pressure
Engine oil temperature
Relief valve opening pressure
Wet sump
At 5C (40F) or higher
Yamalube 4 (20W40) or SAE 20W40
type SE motor oil
At 15C (60F) or lower
Yamalube 4 (10W30) or SAE 10W30
type SE motor oil
3.8 L (3.35 Imp qt, 4.02 US qt)
2.9 L (2.55 Imp qt, 3.07 US qt)
3.1 L (2.73 Imp qt, 3.28 US qt)
230 kPa at 5,000 r / min
(2.3 kg / cm
2 at 5,000 r / min)
(2.3 bar at 5,000 r / min)
(32.7 psi at 5,000 r / min)
100C (212F)
600  680 kPa (6.0  6.8 kg / cm
2,
6.0  6.8 bar, 87.0  98.6 psi)
























ProCarManuals.com

2-3
ENGINE SPECIFICATIONSSPEC
ItemStandardLimit
Oil filter
Oil filter type
Bypass valve opening pressure
Paper
80  120 kPa (0.8  1.2 kg / cm2,
0.8  1.2 bar, 11.6  17.4 psi)








Oil pump
Oil pump type
Inner-rotor-to-outer-rotor-tip
clearance
Outer-rotor-to-oil-pump-housing
clearance
Trochoid
0.01  0.10 mm
(0.0004  0.0039 in)
0.09  0.15 mm
(0.00035  0.0059 in)



0.18 mm
(0.0071 in)
0.22 mm
(0.0087 in)
Cooling system
Radiator capacity
Radiator cap opening pressure
Radiator core
Width
Height
Depth
Coolant reservoir
Capacity
Water pump
Water pump type
Reduction ratio
Max. impeller shaft tilt
2.51 L (2.21 Imp qt, 2.65 US qt)
108  137 kPa (1.08  1.37 kg / cm2,
1.0  1.3 bar, 15.6  19.9 psi)
380 mm (14.96 in)
258 mm (10.2 in)
24 mm (0.94 in)
0.25 L (0.22 Imp qt, 0.26 US qt)
Single suction centrifugal pump
65 / 43
25 / 32 (1.181)































0.15 mm
(0.006 in)
Starting system typeElectric starter
Spark plugs
Model (manufacturer)
quantity
Spark plug gap
CR9EK (NGK)
4
0.6  0.7 mm (0.0236  0.0276 in)







Cylinder head
Volume
Max. warpage
12.5  13.1 cm3 (0.76  0.80 cu.in)







0.10 mm
(0.0039 in)
ProCarManuals.com

2-10
ENGINE SPECIFICATIONSSPEC
ItemStandardLimit
Transmission
Transmission type
Primary reduction system
Primary reduction ratio
Secondary reduction system
Secondary reduction ratio
Operation
Gear ratios
1st gear
2nd gear
3rd gear
4nd gear
5th gear
6th gear
Max. main axle runout
Max. drive axle runout
Constant mesh, 6-speed
Spur gear
65 / 43 (1.512)
Chain drive
45 / 17 (2.647)
Left-foot operation
38 / 15 (2.533)
33 / 16 (2.063)
37 / 21 (1.762)
35 / 23 (1.522)
30 / 22 (1.364)
33 / 26 (1.269)























































0.08 mm
(0.0032 in)
0.08 mm
(0.0032 in)
Shifting mechanism
Shift mechanism type
Max. shift fork guide bar bending
Shift drum / Guide bar







0.10 mm
(0.0039 in)
Air filter typeOil coated paper element



Fuel pump
Pump type
Model (manufacturer)
Output pressure
Electrical
5PW (DENSO)
294 kPa (2.94 kg / cm
2, 2.94 bar, 42.6 psi)












Throttle position sensor
Resistance
Output voltage (at idle)
4.9  5.1 kΩ at 20C (68F)
0.63  0.73 V



Throttle bodies
Model (manufacturer)
quantity
Intake vacuum pressure
Throttle cable free play (at the flange
45EIDW (MIKUNI)
2
22 kPa (165 mmHg, 6.4966 inHg)
3  5 mm (0.12  0.20 in)











of the throttle grip)
ID mark
Throttle valve size
5VY1 00 (USA)
5VY5 10 (CAL)
#100







ProCarManuals.com

2-19
TIGHTENING TORQUESSPEC
Use a lock
washer
TIGHTENING TORQUES
ENGINE TIGHTENING TORQUES
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmm
kgft
lbRemarks
Spark plugs—M104131.39.4
Cylinder headNutM1010See NOTE 1
BoltM62121.28.7
Camshaft capsBoltM628101.07.2
Cylinder head coverBoltM66121.28.7
Cylinder head (exhaust pipe)Stud boltM88151.511
Air indication system capBoltM64101.07.2
Camshaft sprocketsBoltM74242.417
Cylinder head and throttle bodyClampM5430.32.2
Connecting rod capsBoltM8820+1502.0+15014+150
Generator rotorBoltM101606.043
Timing chain tensionerBoltM62101.07.2
Water pump outlet pipeBoltM61101.07.2
Water pump inlet pipeBoltM61101.07.2
(water pump side)
Water pump inlet pipe (front side)BoltM61101.07.2
Oil / water pump assembly
sprocketBoltM61151.511
Water pumpBoltM62121.28.7
Thermostat coverNutM62101.07.2
Thermostat inlet pipeBoltM61101.07.2
Oil coolerBoltM201636.346
Engine oil drain boltBoltM141434.331
Oil pipeBoltM62101.07.2
Oil strainerBoltM63101.07.2
Oil delivery pipeBoltM63101.07.2
Oil filter union boltBoltM201707.051
Oil filter—M201171.712
Oil panBoltM614121.28.7
Oil panBoltM61121.28.7
Air filter case coverScrewM5101.70.171.2
Throttle body and throttle body
jointClampM5430.32.2
Throttle body and funnelBoltM564.20.423.0
Throttle cableNutM614.50.453.3
Throttle cable adjusterBoltM614.50.453.3
Stator coilScrewM63141.410
Generator rotor cover and
bearing housingScrewM63101.07.2
Pull lever coverBoltM62101.07.2
Thermostat assembly stayBoltM62101.07.2
Starter clutch idler gearBoltM61101.07.2
Clutch bossNutM201959.569Stake
Clutch springBoltM66101.07.2
Drive sprocketNutM221858.561
ProCarManuals.com

2-30
LUBRICATION DIAGRAMSSPEC
1Intake camshaft
2Exhaust camshaft
3Oil filter cartridge
4Oil level switch
EAS00034
LUBRICATION DIAGRAMS
ProCarManuals.com

2-32
1Oil cooler
2Oil filter cartridge
3Oil level switch
4Oil strainer
5Oil pump
6Oil pipe
LUBRICATION DIAGRAMSSPEC
ProCarManuals.com

2-40
P To the air filter
Q Route the fuel tank drain hose
over the canister stay and be-
tween the breather hose 2 and
wire harness. On the front side of
the canister stay, let though the
bottom of the A.C.magneto lead
and the wire harness.
R Route by the upside of vehicle
away from the canister stay.
CABLE ROUTINGSPEC
I The coupler for the air induction
solenoid lead and camshaft sen-
sor lead should be connected
above the ignition coil sub wire
harness and it should not drop
on the cylinder head cover be-
hind the ignition coil.
J Pass the right handlebar switch
lead between the frame and heat
protector.
K Coolant reservoir tank drain
hose should cross with the
speed sensor lead under the
swingarm bracket. Route the
coolant reservoir tank drain hose
over the up side of the vehicle.L Pass the rear brake light switch
lead between the swingarm
bracket and coolant reservoir
tank.
M Release the tip of the clamp and
install it to the clutch cable.
Insert the clamp to the hole lo-
cated on the right back side of
the radiator.
Radiator fan motor lead should
not be caught while inserting the
clamp.
N Push the clamp until it hits the ra-
diator side stay. Radiator fan mo-
tor lead should not be caught.
O Clamp the clutch cable so that it
is within this specified clamp.
ProCarManuals.com

3-2
NOTE:
GENERAL MAINTENANCE AND LUBRICATION CHART
CHK
ADJ
NOTE:
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
9*Swingarm pivot
bearings
(See page 4-71)
Check bearing assemblies for looseness.
Moderately repack with lithium-soap-based
grease.
Repack.
10Drive chain
(See page 3-49, 50)
Check chain slack/alignment and condition.
Adjust and lubricate chain with a special O-
ring chain lubricant thoroughly.Every 600 mi (800 km) and after washing the motorcycle or riding in the rain
11*Steering bearings
(See page 3-51)
Check bearing assembly for looseness.
Moderately repack with lithium-soap-based
grease every 16000 mi (25000 km) or 24
months.



Repack.

12*Steering damper
(See page 4-60)
Check operation and for oil leakage.





13*Chassis fasteners
(See page 2-23)
Check all chassis fitting and fasteners.
Correct if necessary.





14Brake and clutch
lever pivot shafts
(See page 3-61)
Apply lithium-soap-based grease (all-purpose
grease) lightly.





15Sidestand pivot(See page 3-61)

Check operation.

Apply lithium-soap-based grease (all-pur-
pose grease) lightly.





16*Sidestand switch
(See page 3-61, 8-4)
Check operation and replace if necessary.






17*Front fork
(See page 3-53)
Check operation and for oil leakage.
Replace if necessary.





18*Shock absorber
assembly
(See page 3-56, 4-67)
Check operation and for oil leakage.
Replace if necessary.





19*Rear suspension
link pivots
(See page 4-71)
Check operation.
Correct if necessary.


20Engine oil
(See page 3-26, 28)
Change (warm engine before draining.)






21*Engine oil filter cartridge
(See page 3-28)
Replace.



22*Cooling system

Check hoses for cracks or damage.
Replace if necessary.





22*Cooling system(See page 3-37, 38, 39)
Change with ethylene glycol antifreeze cool-
ant every 24 months.Change.
23*EXUP system
(See page 3-36)
Check operation, cable free play and pulley
position.
Every 12000 mi (19000 km)
24*Control cables
(See page 3-61)
Apply Yamaha chain and cable lube or en-
gine oil SAE 10W-30 thoroughly.






25*Throttle grip housing
and cable
(See page 3-22)
Check operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.





* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi
(13000 km) or 12 months.
Air filter

This model’s air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.

The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake service

After disassembling the brake master cylinders and calipers, always change the fluid. Regularly
check the brake fluid levels and fill the reservoirs as required.

Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.

Replace the brake hoses every four years and if cracked or damaged.
ProCarManuals.com