torque YAMAHA YZF-R1SC 2004 Service Manual

22
1
3
5
7
9
2
4
8
6
2425
2321
192018
161715
1413
1112
10
GEN
INFOSPEC
ENG
FI ELECCOOL CHK
ADJ
TRBL
SHTG
CHAS
EAS00008
SYMBOLS
The following symbols are not relevant to every
vehicle.
Symbols
1 to 9 indicate the subject of each
chapter.
1General information
2Specifications
3Periodic checks and adjustments
4Chassis
5Engine
6Cooling system
7Fuel injection system
8Electrical system
9Troubleshooting
Symbols 10 to 17 indicate the following.
10Serviceable with engine mounted
11Filling fluid
12Lubricant
13Special tool
14Tightening torque
15Wear limit, clearance
16Engine speed
17Electrical data
Symbols 18 to 23 in the exploded diagrams indi-
cate the types of lubricants and lubrication
points.
18Engine oil
19Gear oil
20Molybdenum-disulfide oil
21Wheel-bearing grease
22Lithium-soap- based grease
23Molybdenum-disulfide grease
Symbols 24 to 25 in the exploded diagrams indi-
cate the following.
24Apply locking agent (LOCTITE)
25Replace the part
ProCarManuals.com

CHAPTER 1
GENERAL INFORMATION
MOTORCYCLE IDENTIFICATION1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION NUMBER 1-1. . . . . . . . . . . . . . . . . . . . . . . .
MODEL LABEL 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT FUNCTIONS 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT INFORMATION1-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARATION FOR REMOVAL AND DISASSEMBLY 1-6. . . . . . . . .
REPLACEMENT PARTS 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GASKETS, OIL SEALS AND O-RINGS 1-6. . . . . . . . . . . . . . . . . . . . . . .
LOCK WASHERS / PLATES AND COTTER PINS 1-7. . . . . . . . . . . . . .
BEARINGS AND OIL SEALS 1-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCLIPS 1-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CONNECTIONS1-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS1-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 2
SPECIFICATIONS
GENERAL SPECIFICATIONS2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE SPECIFICATIONS2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS SPECIFICATIONS2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SPECIFICATIONS2-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONVERSION TABLE2-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL TIGHTENING TORQUE SPECIFICATIONS2-18 . . . . . . . . . . . .
TIGHTENING TORQUES2-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE TIGHTENING TORQUES 2-19. . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS TIGHTENING TORQUES 2-23. . . . . . . . . . . . . . . . . . . . . . . . . .
LUBRICATION POINTS AND LUBRICANT TYPES2-25 . . . . . . . . . . . . . . .
ENGINE 2-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS 2-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM DIAGRAMS2-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE OIL LUBRICATION CHART2-29 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com

2-18
EAS00030
GENERAL TIGHTENING TORQUE
SPECIFICATIONS
This chart specifies tightening torques for stan-
dard fasteners with a standard ISO thread
pitch. Tightening torque specifications for spe-
cial components or assemblies are provided
for each chapter of this manual. To avoid war-
page, tighten multi-fastener assemblies in a
crisscross pattern and progressive stages until
the specified tightening torque is reached. Un-
less otherwise specified, tightening torque
specifications require clean, dry threads. Com-
ponents should be at room temperature.
A: Distance between flats
B: Outside thread diameter
A
(nut)B
(bolt)General tightening
torques
10 mm
12 mm
14 mm
17 mm
19 mm
22 mm6 mm
8 mm
10 mm
12 mm
14 mm
16 mmNm m
kg
6
15
30
55
85
1300.6
1.5
3.0
5.5
8.5
13.0
ft
lb
4.3
11
22
40
61
94
CONVERSION TABLE /
GENERAL TIGHTENING TORQUE SPECIFICATIONS
SPEC
EAS00028
CONVERSION TABLE
All specification data in this manual are listed in
SI and METRIC UNITS.
Use this table to convert METRIC unit data to
IMPERIAL unit data.
Ex.
METRIC MULTIPLIER IMPERIAL
** mm

0.03937 = ** in
2 mm

0.03937 = 0.08 in
CONVERSION TABLE
METRIC TO IMPERIAL
Metric unitMultiplierImperial unit
Tighten-
ing
torquem
kg
m
kg
cm
kg
cm
kg7.233
86.794
0.0723
0.8679ft
lb
in
lb
ft
lb
in
lb
Weightkg
g2.205
0.03527lb
oz
Speedkm / hr0.6214mph
Distance
km
m
m
cm
mm0.6214
3.281
1.094
0.3937
0.03937mi
ft
yd
in
in
Volume /
Capacity
cc (cm3)
cc (cm3)
lt (liter)
lt (liter)0.03527
0.06102
0.8799
0.2199oz (IMP liq.)
cu
in
qt (IMP liq.)
gal (IMP liq.)
Misc.
kg / mm
kg / cm2
Centigrade
(C)
55.997
14.2234
9 / 5+32lb / in
psi (lb / in2)
Fahrenheit
(F)
ProCarManuals.com

2-19
TIGHTENING TORQUESSPEC
Use a lock
washer
TIGHTENING TORQUES
ENGINE TIGHTENING TORQUES
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmm
kgft
lbRemarks
Spark plugs—M104131.39.4
Cylinder headNutM1010See NOTE 1
BoltM62121.28.7
Camshaft capsBoltM628101.07.2
Cylinder head coverBoltM66121.28.7
Cylinder head (exhaust pipe)Stud boltM88151.511
Air indication system capBoltM64101.07.2
Camshaft sprocketsBoltM74242.417
Cylinder head and throttle bodyClampM5430.32.2
Connecting rod capsBoltM8820+1502.0+15014+150
Generator rotorBoltM101606.043
Timing chain tensionerBoltM62101.07.2
Water pump outlet pipeBoltM61101.07.2
Water pump inlet pipeBoltM61101.07.2
(water pump side)
Water pump inlet pipe (front side)BoltM61101.07.2
Oil / water pump assembly
sprocketBoltM61151.511
Water pumpBoltM62121.28.7
Thermostat coverNutM62101.07.2
Thermostat inlet pipeBoltM61101.07.2
Oil coolerBoltM201636.346
Engine oil drain boltBoltM141434.331
Oil pipeBoltM62101.07.2
Oil strainerBoltM63101.07.2
Oil delivery pipeBoltM63101.07.2
Oil filter union boltBoltM201707.051
Oil filter—M201171.712
Oil panBoltM614121.28.7
Oil panBoltM61121.28.7
Air filter case coverScrewM5101.70.171.2
Throttle body and throttle body
jointClampM5430.32.2
Throttle body and funnelBoltM564.20.423.0
Throttle cableNutM614.50.453.3
Throttle cable adjusterBoltM614.50.453.3
Stator coilScrewM63141.410
Generator rotor cover and
bearing housingScrewM63101.07.2
Pull lever coverBoltM62101.07.2
Thermostat assembly stayBoltM62101.07.2
Starter clutch idler gearBoltM61101.07.2
Clutch bossNutM201959.569Stake
Clutch springBoltM66101.07.2
Drive sprocketNutM221858.561
ProCarManuals.com

2-20
TIGHTENING TORQUESSPEC
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmm
kgft
lbRemarks
Exhaust pipe and cylinder headNutM88202.014
Catalyst pipe assembly and
mufflerBoltM82202.014
Exhaust pipe and exhaust valveBoltM65101.07.2
pipe assembly
Exhaust valve pipe and housingBoltM61101.07.2
Pulley and shaft armNutM6170.75.0
EXUP pulley bracketBoltM61101.07.2
EXUP pulley coverBoltM62101.07.2
Exhaust valve pipe and bracketBoltM81202.014
EXUP cable nutNutM6270.75.0
Catalyst pipe bracket and frameBoltM81202.014
Catalyst pipe and catalyst pipeBoltM81202.014
bracket
Exhaust valve pipe and catalyst
pipeBoltM81202.014
EXUP servo motorBoltM6270.75.0
Muffler and rear frameBoltM82232.317
Muffler coverBoltM62101.07.2
CrankcaseStud boltM101080.85.8
Crankcase (main journal)BoltM910See NOTE 2
CrankcaseBoltM610121.28.7
CrankcaseBoltM81242.417
CrankcaseBoltM85242.417
Generator rotor coverBoltM64121.28.7
Generator rotor coverBoltM83222.216
Drive sprocket coverBoltM62101.07.2
Drive sprocket coverBoltM61101.07.2
Crankcase cover (left)ScrewM63101.07.2
Clutch coverBoltM67121.28.7
Clutch coverBoltM61121.28.7
Pickup rotor coverBoltM66121.28.7
Breather coverBoltM64121.28.7
Breather plateBoltM63101.07.2
PlateBoltM62101.07.2
Pickup rotor cover blind boltBoltM81151.511
Generator rotor cover plugPlugM20180.85.8
Main gallery plug (oil return)PlugM16380.85.8
Main gallery plugPlugM20180.85.8
Oil return pipeBoltM62101.07.2
Oil return plugScrewM122242.417
Stator coil leadBoltM61101.07.2
ProCarManuals.com

2-21
TIGHTENING TORQUESSPEC
NOTE 1:
NOTE 2:
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmm
kgft
lbRemarks
Main axle bearing housingBoltM63121.28.7
Shift fork shaft stopperBoltM62101.07.2
Stopper screwScrewM81222.216
Shift rod lock nut (rear)NutM6170.75.0Left thread
Shift rod lock nut (front)NutM6170.75.0
Shift rod jointBoltM61101.07.2
Shift armBoltM61101.07.2
E.C.U.ScrewM6270.75.0
Neutral switch—M101202.015
EXUP servo motor coverScrewM5220.21.5
Coolant temperature sensor—M121181.813
Cylinder identification sensorBoltM6180.85.7
Atmospheric pressure sensorScrewM5270.75.0
Crankshaft position sensorBoltM61101.07.2
Oil level switchBoltM62101.07.2
1. First, tighten the bolts to approximately 19 Nm (1.9 m
kg, 14 ft
lb) with a torque wrench following the
tightening order.
2. Retighten the bolts 67 Nm (6.7 m
kg, 48 ft
lb) with a torque wrench.
1. First, tighten the bolts to approximately 20 Nm (2.0 m
kg, 15 ft
lb) with a torque wrench following the
tightening order.
2. Loosen the all bolts one by one following the tightening order and then tighten them to 20 Nm (2.7
m
kg, 15 ft
lb) again.
3. Retighten the bolts further to reach the specified angle (60).
ProCarManuals.com

2-22
TIGHTENING TORQUESSPEC
Cylinder head tightening sequence:
Crankcase tightening sequence.
ProCarManuals.com

2-23
TIGHTENING TORQUESSPEC
See NOTE 2 CHASSIS TIGHTENING TORQUES
ItemThreadTighteningRemarksItemsizeNmm
kgft
lbRemarks
Upper bracket and outer tubeM8262.619
Upper bracket and steering stem nutM2811 311.382
Handlebar and outer tubeM8171.712
Handlebar and upper bracketM6131.39
Steering shaft and ring nutM30181.813See NOTE 1
Outer tube and under bracketM8232.317
Main switch and upper bracketM8262.619
Front brake master cylinder cap stopperM41.20.120.9
Front brake hose union boltsM10303.022
Front brake master cylinder and bracketM6131.39
Meter assembly and front cowling stay—1.30.130.9
Headlight and front cowling stay—0.80.080.6
Front cowling and headlight assembly—1.50.151.1
Cover 7, 8 and frameM650.53.6
Under cowling and engineM650.53.6
Windshield and front cowlingM50.40.040.3
Duct and console panelM51.30.130.9
End grip and handlebarM640.42.9
Horn bracket and under bracketM640.42.9
Coolant reservoir tank and frameM650.53.6
Engine mount front (left and right)M10454.533
Engine mount rear upperM10515.137
Engine mount rear underM10515.137
Engine mount rear adjust boltM1670.75.1
Catalyst pipe stay and frameM10444.432
Clutch cable lock nut (engine side)M870.75.1
Main frame and rear frameM10414.130
Throttle cable adjust nut (throttle body side)M650.53.6
Cover 2 and plate—0.80.080.6
Pivot shaft and nutM1810510.576
Connecting rod and frameM10444.432
Relay arm and connecting rodM10444.432
Relay arm and swingarmM10444.432
Rear shock absorber and relay armM10444.432
Rear shock absorber and upper bracketM10444.432
Upper bracket and frameM14929.267
Seal guardM670.75.1
Drive chain caseM670.75.1
Chain puller adjust nutM8161.612
Fuel tank and fuel pump assemblyM540.42.9
Fuel tank stay (front side) and frameM670.75.1
Fuel tank and fuel tank stay (front side)M670.75.1
Fuel tank stay (rear side) and rear frameM670.75.1
Side cover and fuel tankM50.40.040.3
Rider seat and frameM670.75.1
Seat lock plate and rear frameM6101.07
Side cover (rear side) and frameM540.42.9
ProCarManuals.com

2-24
TIGHTENING TORQUESSPEC
NOTE 1:
NOTE 2:
NOTE 3:
ItemThreadTighteningRemarksItemsizeNmm
kgft
lbRemarks
Battery box and frameM670.75.1
Atmospheric pressure sensor and battery box—0.70.070.5
Lean angle cut-off switch and battery box—20.21.4
Foot rest bracket (front) and frameM8282.820
Foot rest bracket (rear) and frameM8282.820
Rear brake master cylinder and foot rest bracketM6181.813
Rear brake hose union boltM10303.022
Sidestand bracket and frameM10636.346
Front wheel axle shaft and boltM14919.166
Rear wheel axle nutM2415015.0109
Front brake caliper and front forkM10353.525
Front brake disc and front wheelM6181.813
Rear brake disc and rear wheelM6303.022
Rear wheel sprocket and drive hubM1010010.072
Brake caliper bleed screwM860.64.3
Front wheel axle pinch boltM8202.014See NOTE 3
1. First, tighten the ring nut to approximately 52 Nm (5.2 m
kg, 38 ft
lb) with a torque wrench, then
loosen the ring nut completely.
2. Retighten the lower ring nut to specification.
Refer to “INSTALLING THE ENGINE” in chapter 5.
1. Insert the front wheel axle from the right side
and tighten it with the flange bolt from the left
side to 91 Nm (9.1 m
kg, 65.8 ft
lb).
2. In the order from the pinch bolt
2
pinch
bolt
1
pinch bolt 2, tighten each bolt to
20 Nm (2.0 m
kg, 14 ft
lb) without perform-
ing temporary tightening.
3. Check that the end face of the axle head and
the end face of the fork side are flush-
mounted. If they are out of alignment, make
sure to fit them by adding the external force
by hand or with a plastic hammer, etc.
If the end face of the axle is not parallel to the
end face of the fork, align them so that one
point of the axle circumference is positioned
on the end face of the fork.
At this stage, it can be accepted if the end
face of the axle becomes partially concave
to the end face of the fork.
4. In the order from the pinch bolt
4
pinch
bolt
3
pinch bolt 4, tighten each bolt to
20 Nm (2.0 m
kg, 14 ft
lb) without perform-
ing temporary tightening.
ProCarManuals.com

3-6
FUEL TANK
CHK
ADJ
4 Nm (0.4 m
kg, 2.9 ft
lb)
NOTE:
CAUTION:
INSTALLING THE FUEL PUMP
1. Install:

fuel pump

Do not damage the installation surfaces of the
fuel tank when installing the fuel pump.

Always use a new fuel pump gasket.

Install the fuel pump as shown in the illustra-
tion.

Tighten the fuel pump bolts in stages in a criss-
cross pattern and to the specified torque.
INSTALLING THE FUEL TANK
1. Install:

fuel hose

fuel return hose

fuel hose connector cover
When installing the fuel hose, make sure
that it is securely connected, and that the
fuel hose holder is in the correct position,
otherwise the fuel hose will not be properly
installed.
ProCarManuals.com