wiring diagram YAMAHA YZF-R1SC 2004 Service Manual

CHECKING THE WATER PUMP 6-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLING THE WATER PUMP 6-15. . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 7
FUEL INJECTION SYSTEM
FUEL INJECTION SYSTEM7-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WIRING DIAGRAM 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECU’S SELF-DIAGNOSTIC FUNCTION 7-4. . . . . . . . . . . . . . . . . . . . . .
SUBSTITUTE CHARACTERISTICS OPERATION CONTROL
(FAIL-SAFE ACTION) 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAIL-SAFE ACTIONS TABLE 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING CHART 7-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC MODE 7-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING DETAILS 7-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE BODIES7-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INJECTORS 7-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE INJECTORS 7-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE THROTTLE BODIES 7-39. . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE THROTTLE BODY JOINTS 7-39. . . . . . . . . . . . . . . . . .
CHECKING THE PRESSURE REGULATOR 7-40. . . . . . . . . . . . . . . . . .
CHECKING THE FUEL PUMP AND PRESSURE REGULATOR
OPERATION 7-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE THROTTLE POSITION
SENSOR 7-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE SUB-THROTTLE POSITION
SENSOR 7-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE THERMO WAX 7-45. . . . . . . . . . . .
AIR INDUCTION SYSTEM7-46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR INJECTION 7-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR CUT-OFF VALVE 7-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR INDUCTION SYSTEM DIAGRAMS 7-47. . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE AIR INDUCTION SYSTEM 7-48. . . . . . . . . . . . . . . . . .
CHAPTER 8
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS8-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING SWITCH CONTINUITY8-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE SWITCHES8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE BULBS AND BULB SOCKETS8-5 . . . . . . . . . . . . . . . . .
TYPES OF BULBS 8-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CONDITION OF THE BULBS 8-5. . . . . . . . . . . . . . . .
ProCarManuals.com

7-2
FUEL INJECTION SYSTEMFI
7
WIRING DIAGRAM
ProCarManuals.com

8-13
IGNITION SYSTEMELEC
12. Starting circuit cut-off relay (diode)

Disconnect the starting circuit cut-off relay
coupler from the wire harness.

Connect the pocket tester (Ω
1) to the
starting circuit cut-off relay coupler as
shown.

Check the starting circuit cut-off relay for
continuity.
Positive tester probe

blue / yellow
Negative tester probe

sky blue
1
2
EAS00753
Positive tester probe

blue / yellow
Negative tester probe

blue / black Continuity
1
3
Positive tester probe

sky blue
Negative tester probe

blue / yellow
2
1
Positive tester probe

blue / black
Negative tester probe

blue / yellow No
continuity
3
1
YESNO
Replace the starting
circuit cut-off relay. When you switch the positive and negative
tester probes, the readings in the above chart
will be reversed.

Are the tester readings correct?
NOTE:
13. Lean angle cut-off switch

Check the lean angle cut-off switch.
Refer to “FUEL INJECTION SYSTEM” in
chapter 7.

Is the lean angle cut-off switch OK?
YESNO
Replace the lean
angle cut-off switch.
EAS00754
14. Wiring

Check the entire ignition system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the ignition system’s wiring properly con-
nected and without defects?
YESNO
Properly connect or
repair the ignition
system’s wiring.
Replace the ECU.
ProCarManuals.com

8-18

Check the entire starting system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the starting system’s wiring properly con-
nected and without defects?
EAS00766
12. Wiring
YESNO
Properly connect or
repair the starting
system’s wiring.
The starting system
circuit is OK.
11. Start switch

Check the start switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the start switch OK?
YESNO
Replace the right
handlebar switch.
EAS00764
10. Clutch switch

Check the clutch switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the clutch switch OK?
YESNO
Replace the clutch
switch.
EAS00763EAS00752
9. Sidestand switch

Check the sidestand switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the sidestand switch OK?
YESNO
Replace the side-
stand switch.
ELECTRIC STARTING SYSTEMELEC
ProCarManuals.com

8-26
CHARGING SYSTEMELEC
YESNO 5. Stator coil resistance

Remove the generator cover.

Connect the pocket tester (Ω
1) to the sta-
tor coils as shown.
Replace the stator
coil assembly.
EAS00776
Positive tester probe
white
Negative tester probe
white
Positive tester probe
white
Negative tester probe
white1
1
2
3

Measure the stator coil resistances.
Stator coil resistance
0.14  0.18 Ω at 20C (68F)

Is the stator coil OK?
YESNO 6. Wiring

Check the wiring connections of the entire
charging system.
Refer to “CIRCUIT DIAGRAM”.

Is the charging system’s wiring properly con-
nected and without defects?
Properly connect or
repair the charging
system’s wiring.
EAS00779
Replace the rectifi-
er / regulator.
4. Stator coil lead

Disconnect stator coil lead coupler.

Connect the pocket tester (Ω
1) to the sta-
tor coil lead coupler as shown.
Positive tester probe

white
Negative tester probe

ground
3
Positive tester probe

white
Negative tester probe

ground
1
Positive tester probe

white
Negative tester probe

groundNo
continuity
2
YESNO
Replace the stator
coil lead.
Are the tester readings correct?
ProCarManuals.com

8-30

Does the Headlight relay (dimmer) have
continuity between red / yellow and
black / green ?
NOYES
Replace the dimmer
relay. Positive tester probe
red / yellow
Negative tester probe
black / green
1
2
3
4
5. Headlight relay (on / off)

Disconnect the headlight relay (on / off) from
the coupler.

Connect the pocket tester (Ω
1) and bat-
tery (12 V) to the headlight relay (on / off) as
shown.
Positive battery lead
red / yellow
Negative battery lead
yellow / black
EAS00787
YESNO 7. Wiring

Check the entire lighting system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the lighting system’s wiring properly con-
nected and without defects?
Properly connect or
repair the lighting
system’s wiring.
Check the condition
of each of the lighting
system’s circuits.
Refer to “CHECK-
ING THE LIGHTING
SYSTEM”.

Does the headlight relay (dimmer) have
continuity between black / green and
black / yellow ?
Positive tester probe
black / green
Negative tester probe
black / yellow
1
2
3
4
6. Headlight relay (dimmer)

Disconnect the headlight relay (dimmer)
from the coupler.

Connect the pocket tester (Ω
1) and bat-
tery (12 V) to the headlight relay (dimmer) as
shown.
Positive battery lead
black
Negative battery lead
yellow
3
4
3
4
YESNO
Replace the head-
light relay (dimmer).
LIGHTING SYSTEMELEC
ProCarManuals.com

8-36
YESNO

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?
YESNO
Replace the main
switch.
YESNO 1. Horn switch

Check the horn switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the horn switch OK?
Replace the left han-
dlebar switch.
EAS00796
CHECKING THE SIGNALING SYSTEM
1. The horn fails to sound.
EAS00795
4. Wiring

Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the signaling system’s wiring properly
connected and without defects?
YESNO
Properly connect or
repair the signaling
system’s wiring.
Check the condition
of each of the signal-
ing system’s circuits.
Refer to “CHECK-
ING THE LIGHTING
SYSTEM”.
SIGNALING SYSTEMELEC
NOTE:
YESNO
1. Backup, main, ignition, signal and park
fuses

Check the backup, main, ignition, signal and
park fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the backup, main, ignition, signal and
park fuses OK?
Replace the fuse(s).
2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?
EAS00739EAS00794
TROUBLESHOOTING

Any of the following fail to light: turn sig-
nal light, brake light or an indicator light.

The horn fails to sound.
Check:
1. backup, main, ignition, signal, and park
fuses
2. battery
3. main switch
4. wiring connections
(of the entire signaling system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-47
COOLING SYSTEMELEC

Remove the coolant temperature sensor.

Connect the pocket tester (Ω
1k) to the
coolant temperature sensor as shown.

Immerse the coolant temperature sensor in
a container filled with coolant .
Make sure the coolant temperature sensor
terminals do not get wet.

Place a thermometer in the coolant.

Slowly heat the coolant, and then let it cool to
the specified temperature indicated in the
table.

Check the coolant temperature sensor for
continuity at the temperatures indicated in
the table.
EAS00812
1
Coolant temperature sensor
resistance
0C (32F): 5.21  6.37 kΩ
80C (176F): 0.29  0.35 kΩ
WARNING

Handle the coolant temperature sensor
with special care.

Never subject the coolant temperature
sensor to strong shocks. If the coolant
temperature sensor is dropped, replace
it.
6. Coolant temperature sensor
Replace the coolant
temperature sensor.
NOYES
Coolant temperature sensor
20 Nm (2.0 m
kg, 14 ft
lb)
Three bond sealock
10

Does the coolant temperature sensor oper-
ate properly?
7. Wiring

Check the entire cooling system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the cooling system’s wiring properly con-
nected and without defects?
Properly connect or
repair the cooling
system’s wiring.
NOYES
This circuit is OK.
EAS00813
2
NOTE:
3
ProCarManuals.com

8-51
FUEL PUMP SYSTEMELEC
YESNO 5. Starting circuit cut-off relay (fuel injection
system relay)

Disconnect the starting circuit cut-off relay
coupler from the wire harness.

Connect the pocket tester (Ω
1) and bat-
tery (12 V) to the starting circuit cut-off relay
coupler as shown.
Replace the starting
circuit cut-off relay.
Positive battery lead
red / black
Negative battery lead
blue / yellow 1
2
Positive tester probe
red
Negative tester probe
red / blue3
4

Does the starting circuit cut-off relay have
continuity between red and red / blue?
YESNO 6. Fuel pump resistance

Disconnect the fuel pump coupler from the
wire harness.

Connect the pocket tester (Ω
1) to the fuel
pump coupler as shown.
Properly connect or
repair the fuel sys-
tem’s wiring.
1
2
Positive tester probe
red / blue
Negative tester probe
black
EAS00817
YESNO Fuel pump resistance
0.2  3.0 Ω at 20C (68F)

Is the fuel pump OK?
Replace the fuel
pump.

Measure the fuel pump resistance.
7. Wiring

Check the entire fuel pump system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the fuel system’s wiring properly con-
nected and without defects?
EAS00818
Replace the ECU.
EAS00759
ProCarManuals.com

59Clutch switch
60Turn signal switch
61Horn
62Front turn signal / position light (left)
63Front turn signal / position light (right)
64Rear turn signal light (left)
65Rear turn signal light (right)
66Headlight
67Auxiliary light
68License plate light
69Rear brake light switch
70Tail / brake light
71Headlight relay (on / off)
72Headlight relay (dimmer)
73Fuse (ignition)
74Fuse (signal)
75Fuse (headlight)
76Radiator fan motor relay
77Fuse (radiator fan motor left)
78Fuse (radiator fan motor light)
79Radiator fan motor 2
80Radiator fan motor 1
81Ground
COLOR CODE
B Black. . . . .
Br Brown. . . .
Ch Chocolate. . .
Dg Dark green. . .
G Green. . . .
Gy Gray. . .
L Blue. . . . .
Lg Light green. . . .
O Orange. . . .
P Pink. . . . .
R Red. . . . .
Sb Sky blue. . . .
W White. . . .
Y Yellow. . . . .
B / G Black / Green. .
B / L Black / Blue. . .
B / R Black / Red. .
B / W Black / White. .
B / Y Black / Yellow. .
Br / G Brown / Green.
Br / L Brown / Blue. .
Br / R Brown / Red. .
Br / W Brown / White.
G / B Green / Black. .
G / R Green / Red. .
G / W Green / White. . G / Y Green / Yellow. .
Gy / B Gray / Black.
Gy / G Gray / Green.
Gy / R Gray / Red.
L / B Blue / Black. . .
L / R Blue / Red. .
L / W Blue / White. .
L / Y Blue / Yellow. . .
O / B Orange / Black. .
O / G Orange / Green. .
P / W Pink / White. .
R / B Red / Black. .
R / G Red / Green. .
R / L Red / Blue. .
R / W Red / White. .
R / Y Red / Yellow. .
Sb / W Sky blue / White.
W / B White / Black. .
W / R White / Red. .
W / Y White / Yellow. .
Y / B Yellow / Black. .
Y / G Yellow / Green. .
Y / L Yellow / Blue. . .
Y / R Yellow / Red. .
Y / W Yellow / White. .
YZF-R1S / YZF-R1SC WIRING DIAGRAM
1Main switch
2A.C. magneto
3Rectifier / regulator
4Fuse (main)
5Fuse (backup)
6Battery
7Fuse (fuel injection)
8Starter relay
9Starter motor
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
13Fuel pump
14E.C.U
15Ignition coil #1
16Ignition coil #2
17Ignition coil #3
18Ignition coil #4
19Spark plug
20Injector #1
21Injector #2
22Injector #3
23Injector #4
24Air induction system solenoid
25Sub-throttle position sensor
26EXUP servo motor
27Speed sensor
28Coolant temperature sensor
29Intake air temperature sensor
30Option switch
31Crankshaft position sensor
32Throttle position sensor
33Intake air pressure sensor
34Atmospheric pressure sensor
35Cylinder identification sensor
36Lean angle cut-off switch
37Meter assembly
38Fuel level warning light
39Oil level warning light
40Neutral indicator light
41Tacho meter
42Shift timing indicator light
43Multi function meter
44Engine trouble warning light
45Coolant temperature indicator light
46Hi beam indicator light
47Turn signal indicator light (left)
48Turn signal indicator light (light)
49Meter light
50Oil level switch
51Right handlebar switch
52Front brake light switch
53Engine stop switch
54Start switch
55Turn signal relay
56Left handlebar switch
57Dimmer switch
58Horn switch
ProCarManuals.com