width YAMAHA YZF-R7 1999 User Guide

4 - 28
ENGVALVES AND VALVE SPRINGS
e. Apply a fine lapping compound to the
valve face and repeat the above
steps.
f. After every lapping procedure, be
sure to clean off all of the lapping
compound from the valve face and
valve seat.
g. Apply Mechanic’s blueing dye
(Dykem) b onto the valve face.
h. Install the valve into the cylinder
head.
i. Press the valve through the valve
guide and onto the valve seat to make
a clear impression.
j. Measure the valve seat width c
again. If the valve seat width is out of
specification, reface and lap the valve
seat.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
EB403420
CHECKING THE VALVE SPRINGS
The following procedure applies to all of
the valve springs.
1. Measure:
• valve spring free length a
Out of specification ® Replace the
valve spring.
Valve spring free length
Inner spring
Intake valve spring
32.35 mm (1.27 in)
: 30.73 mm
(1.21 in)
Exhaust valve spring
28.82 mm (1.13 in)
: 27.37 mm
(1.08 in)
Outer spring
Intake valve spring
36.42 mm (1.43 in)
: 34.60 mm
(1.36 in)
Exhaust valve spring
33.91 mm (1.34 in)
: 32.21 mm
(1.27 in)

4 - 69
ENGCONNECTING RODS AND PISTONS
c. Put a piece of Plastigaugeâ 1 on the
crankshaft pin.
d. Assemble the connecting rod halves.
NOTE:
• Do not move the connecting rod or
crankshaft until the clearance mea-
surement has been completed.
• Lubricate the bolt threads and nut
seats with MOLYKOTE
® G-n paste.
• Make sure that the “Y” mark c on the
connecting rod faces towards the left
side of the crankshaft.
• Make sure that the characters d on
both the connecting rod and connect-
ing rod cap are aligned.
e. Tighten the connecting rod nuts.
Refer to “INSTALLING THE PISTONS
AND CONNECTING RODS”.
f. Remove the connecting rod and big
end bearings.
Refer to “REMOVING THE CONNECT-
ING RODS AND PISTONS”.
g. Measure the compressed Plasti-
gauge
â width e on the crankshaft
pin.
If the crankshaft pin-to-big end bear-
ing clearance is out of specification,
select replacement big end bearings.
s s s s s s s s s s s s s s s s s s s s s s s s s s s

4 - 77
ENGCRANKSHAFT
g. Remove the lower crankcase and the
crankshaft journal lower bearings.
h. Measure the compressed Plasti-
gauge
Ò width c on each crankshaft
journal.
If the clearance is out of specification,
select replacement crankshaft jour-
nal bearings.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
2. Select:
• crankshaft journal bearings (J
1 ~ J5)
NOTE:
• The numbers stamped into the crank-
shaft web and the numbers stamped
into the lower crankcase are used to
determine the replacement crankshaft
journal bearing sizes.
•“J
1” ~ “J5” refer to the bearings shown
in the crankshaft illustration.
• If “J
1” ~ “J5” are the same, use the
same size for all of the bearings.
t t t t t t t t t t t t t t t t t t t t t t t t t t t
For example, if the crankcase “J1” and
crankshaft web “J
1” numbers are “8”
and “3” respectively, then the bearing
size for “J
1” is:
s s s s s s s s s s s s s s s s s s s s s s s s s s s
Bearing size for J1:
“J
1” (crankcase) – “J1” (crankshaft
web) =
8 – 3 = 5
CRANKSHAFT JOURNAL BEARING
COLOR CODE
1
blue
2
3
black
4
5
brown
6
7
green
8
9
yellow
10
11 violet