relay YAMAHA YZF-R7 1999 Owner's Manual

8 - 29
–+ELECELECTRONIC FUEL INJECTION SYSTEM
1Main switch
5Battery
6Main fuse
CCamshaft sensor
DThrottle position sensor
EIntake air pressure sensor
FAtmospheric pressure sensor
GIntake air temperature sensor
HCoolant temperature sensor
IPickup coil
JECU
KCylinder #1-injector 1
LCylinder #2-injector 1
MCylinder #3-injector 1
NCylinder #4-injector 1
OCylinder #1-injector 2
PCylinder #2-injector 2
QCylinder #3-injector 2
RCylinder #4-injector 2
XFall detection switch
YSpeed sensor
yFuel pump
zMain relay
}Engine stop switch
ŒElectronic fuel injection system fuse
£ECU fuse
TROUBLESHOOTING
NOTE:
• Before troubleshooting, remove the following part(-s):
1) bottom cowling
2) front cowling
• Troubleshoot with the following special tool(-s).
The condition code is displayed by the tachometer.
Check the condition code list to
identify the faulty part. Refer to
“ELECTRICAL CONTROL SYS-
TEM”.
In diagnosis mode, select the
appropriate diagnosis code to
check the operation of the faulty
part.Check the
wiring.Replace.
Co, diagnosis switch box
90890-03171
Test coupler adapter
90890-03149
Out of specifi-
cationNo good

8 - 30
–+ELECELECTRICAL CONTROL SYSTEM
ELECTRICAL CONTROL SYSTEM
The YZF-R7 features an electrical control system with the following modes:
• user mode
• diagnosis mode
• CO emission adjustment mode
NOTE:
The vehicle is normally in user mode. Special tools are needed to switch to a diagnosis mode
or to the CO emission adjustment mode.
USER MODE
• If a circuit is defective, setting the main switch to “ON” (without starting the engine) will
cause the corresponding condition code to be displayed by the tachometer, the warning
light to light up, and the engine trouble symbol to blink. When the engine is started, the
condition code is no longer displayed and the engine speed appears.
• Normally, when the main switch is set to “ON”, the warning light comes on for 1.4 seconds
and then goes off. The warning light also comes on while the start switch is pushed.
• When the engine is not running, the warning light flashes once every 0.16 second if the start
switch is pushed under the following conditions.
• The fall detection switch switches off the main relay.
• Ignition is cut off by the sidestand switch.
• The injector operating voltage decreases to 3 V or less, or the main relay malfunctions.
• The pickup coil is defective.
• The fall detection switch is defective.

8 - 32
–+ELECELECTRICAL CONTROL SYSTEM
Condition code list
NOTE:
* This condition code is also displayed in the following cases:
- when the starter switch is held down for more than 4 seconds, causing the warning
light to flash
- when the ignition circuit cut-off system stops the engine or prevents it from starting
** This condition code is also displayed when the engine is operated at 5,000 r/min for at
least 30 seconds with the rear wheel at standstill.
*** This condition code is also displayed when the engine stop switch is turned to “ ”
while riding with the transmission in gear. Condition
codeCircuit Defect(s) System response
11 Camshaft sensor • No incoming sig-
nalThe ECU pairs the ignition of cyl-
inders #1 and #4 and cylinders #2
and #3. The motorcycle can be
ridden.
12* Pickup coil • No incoming sig-
nalThe motorcycle cannot be ridden.
13 Intake air pressure
sensor• Disconnected
• Short-circuitThe ECU stays set to an intake air
pressure of 760 mm Hg (29.9 in Hg).
The motorcycle can be ridden.
14 Intake air pressure
sensor hose and
negative pressure
hose• Improper connec-
tion
• Bending
15 Throttle position
sensor• Disconnected
• Short-circuitThe ECU stays set to a wide throt-
tle opening.
The motorcycle can be ridden.
16 Throttle position
sensor• Locked
21 Coolant tempera-
ture sensor• Disconnected
• Short-circuitThe ECU stays set to a coolant
temperature of 80˚C (176˚F).
The motorcycle can be ridden.
22 Intake air tempera-
ture sensor• Disconnected
• Short-circuitThe ECU stays set to an intake air
temperature of 40˚C (104˚F).
The motorcycle can be ridden.
23 Atmospheric pres-
sure sensor• Disconnected
• Short-circuitThe ECU stays set to an atmo-
spheric pressure of 760 mm Hg
(29.9 in Hg).
The motorcycle can be ridden.
41 Fall detection
switch• Disconnected The main relay stays switched off.
The motorcycle cannot be ridden.
42** Speed sensor • Incorrect signal The ECU stays set to 6th gear.
The motorcycle can be ridden.
43*** Monitored voltage • Incorrect The ECU stays set to a monitored
voltage of 12 V.
The motorcycle can be ridden.
44 ROM operation • CO emission
adjustment errorThe CO emission adjustment is
set to 0.

8 - 37
–+ELECELECTRICAL CONTROL SYSTEM
12 Main relay CO, diagnosis switch box method
Within one second after the
MODE switch is released, the
main relay is switched on once
every second for the next five
seconds. During this time, the
warning light lights up as long as
the relay is switched on.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the main relay is switched
off, then on again. The warning
light lights up while the relay is
switched off.
13 Ignition coil for
cylinder #1CO, diagnosis switch box method
Within one second after the
MODE switch is released, the
ignition coil for the selected cylin-
der is operated once every sec-
ond for the next five seconds.
During this time, the warning
light lights up for 0.5 second
once every second.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the ignition coil for the
selected cylinder is operated
once every second for the next
five seconds. During this time,
the warning light lights up for 0.5
second once every second. 14 Ignition coil for
cylinder #2
15 Ignition coil for
cylinder #3
16 Ignition coil for
cylinder #4 Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)

8 - 38
–+ELECELECTRICAL CONTROL SYSTEM
17 Injector 1 for cyl-
inder #1CO, diagnosis switch box method
Before selecting a code, discon-
nect the fuel pump coupler from
the wire harness.
Within one second after the
MODE switch is released, the
main relay is turned on, and the
selected injector is operated once
every second for the next five
seconds. During this time, the
warning light lights up for 0.5
second once every second.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the selected injector is
operated for once every second
for the next five seconds. During
this time, the warning light lights
up for 0.5 second once every sec-
ond. 18 Injector 1 for cyl-
inder #2
19 Injector 1 for cyl-
inder #3
20 Injector 1 for cyl-
inder #4
21 Injector 2 for cyl-
inder #1
22 Injector 2 for cyl-
inder #2
23 Injector 2 for cyl-
inder #3
24 Injector 2 for cyl-
inder #4
25 ~ 28 — — —
29 Condition code
record of mal-
functionsThe condition code of any fixed mal-
function is recorded in the ROM and
displayed by the tachometer. Refer
to the condition code list in “USER
MODE” for details on the condition
codes.Condition codes 11
– 44
30 ROM (Clearing
the condition
code record)Selecting this diagnosis code clears
the condition code record of mal-
functions stored in the ROM.
If an error has occurred in a sensor
signal, it was recorded in the ROM
and the tachometer displays 10,000
r/min. If no error has occurred, the
tachometer displays 0 r/min.
CO, diagnosis switch box method
Press the UP switch eight times
within four seconds to clear the con-
dition code record from the ROM.
Test coupler adapter method
Remove the rear cowling.
Disconnect the relay unit coupler
from the relay unit.
Press the start switch ten times
within four seconds to clear the con-
dition code record from the ROM.0 r/min (no error) or
10,000 r/min (errors)
When the error
record is cleared, 0
r/min is displayed.
31 ROM program
versionThe version number of the ROM pro-
gram is displayed in the tachometer. Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)

YZF-R7 WIRING DIAGRAM
1
Main switch

2
Rectifier/regulator

3
Generator

4
Backup fuse (odometer)

5
Battery

6
Main fuse

7
Starter relay

8
Starter motor

9
Diode

0
Relay unit

A
Diode

B
Sidestand switch

C
Camshaft sensor

D
Throttle position sensor

E
Intake air pressure sensor

F
Atmospheric pressure sensor

G
Intake air temperature sensor

H
Coolant temperature sensor

I
Pickup coil

J
ECU

K
Cylinder #1 - injector 1

L
Cylinder #2 - injector 1

M
Cylinder #3 - injector 1

N
Cylinder #4 - injector 1

O
Cylinder #1 - injector 2

P
Cylinder #2 - injector 2

Q
Cylinder #3 - injector 2

R
Cylinder #4 - injector 2

S
Cylinder #1 - ignition coil

T
Cylinder #2 - ignition coil

U
Cylinder #3 - ignition coil

V
Cylinder #4 - ignition coil

W
CDI unit

X
Fall detection switch

Y
Speed sensor

Z
Neutral switch

[
Meter assembly

\
Fuel level indicator light

]
Warning light (oil level indicator)

^
Neutral indicator light

a
Tachometer

b
Combination meter

c
Warning light (coolant temperature indicator)
d
High beam indicator light
e
Turn signal indicator light
f
Meter light
gWarning light (engine trouble indicator)
hOil level switch
i
Horn
jHeadlight
kRear turn signal light (right)
lRear turn signal light (left)
mFront turn signal light (right)
nFront turn signal light (left)
oTail/brake light
pRear brake light switch
q
Left handlebar switch
rClutch switch
sLights switch
t
Pass switch
uDimmer switch
vTurn signal switch
wHorn switch
xTurn signal relay
yFuel pump
zMain relay
{
Right handlebar switch|Front brake light switch
}Engine stop switch
~Start switch
Œ
Electronic fuel injection system fuseCYCLELOCK Signaling system fuse
¢Headlight fuse£
ECU fuse¤Radiator fan motor fuse
¥Thermo switch
¦Radiator fan motor
COLOR CODE
B ............ black
Br ........... brown
Ch .......... chocolate
Dg .......... dark green
G ............ green
Gy .......... gray
L ............ blue
Lg .......... light green
O ............ orange
P ............ pink
R ............ red
Sb .......... sky blue
W ........... white
Y ............ yellow
B/L ......... black/blue
B/R ......... black/red
B/W ....... black/white
B/Y ......... black/yellow
Br/G ....... brown/green
Br/L ........ brown/blue
Br/R ....... brown/red
Br/W ...... brown/white
G/B ........ green/black
G/R ........ green/red
G/W ....... green/white
G/Y ........ green/yellow
Gy/B ...... gray/black
Gy/G ...... gray/green
Gy/R ...... gray/red
L/B ......... blue/black
L/G ......... blue/green
L/R ......... blue/red
L/W ........ blue/white
L/Y ......... blue/yellow
Lg/R ....... light green/red
Lg/Y ....... light green/yellow
O/B ........ orange/black
O/G ........ orange/green
P/B ......... pink/black
P/L ......... pink/blue
P/W ........ pink/white
R/B ......... red/black
R/G ........ red/green
R/L ......... red/blue
R/W ....... red/white
R/Y ......... red/yellow
W/B ....... white/black
W/G ....... white/green
W/L ........ white/blue
W/Y ....... white/yellow
Y/B ......... yellow/black
Y/G ........ yellow/green
Y/L ......... yellow/blue
Y/R ......... yellow/rod