Abarth Punto 2020 Owner handbook (in English)

197
RUBBER HOSES
As far as the brake system and fuel rubber hoses are
concerned, follow the “Scheduled Servicing Programme”
in this chapter carefully.
Ozone, high temperatures and prolonged lack of fluid in
the system may cause hardening and cracking of the
hoses, with possible leaks.
Careful inspections are therefore necessary.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
WINDSCREEN WIPER
BLADES
Periodically clean the rubber part using special products;
TUTELA PROFESSIONAL SC 35 is recommended.
Replace the blades if the rubber edge is deformed or
worn. In any case, it is advisable to replace them
approximately once a year.
A few simple precautions can reduce the possibility of
damage to the blades:
❒make sure that the rubber part is not stuck to the
windscreen at sub-zero temperatures. Use a de-icing
product to release it if required;
❒remove any snow from the glass: in addition to
protecting the blades, this prevents effort from the
motor and overheating;
❒do not operate the windscreen wipers on dry glass.
Driving with worn wiper blades is a
serious hazard, because visibility is
reduced in bad weather.
WARNING
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 197

F0U177Abfig. 173198
F0U176Abfig. 172
Replacing the windscreen wiper blades fig. 172
How to remove the blade:
❒lift the arm A off the windscreen;
❒turn blade B 90° around pin C, located at the end of
the wiper arm;
❒remove the blade from the pin C.
How to insert the blade:
❒fit pin C into the hole located in the middle of the
blade B;
❒refit the arm with the blade on the windscreen.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Changing the rear window blade fig. 173
Proceed as follows:
❒raise the cover A and remove the arm from the car,
slackening the nut B that fastens it to the pivot pin;
❒position the new arm correctly and tighten the nut;
❒lower the cover.
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 198

199F0U179Abfig. 174F0U178Abfig. 175
Rear window washer fig. 175
Rear window washer jets are fixed.
The nozzle holder is located above the rear window. SPRAY NOZZLES
Windscreen washer fig. 174
If the jet of fluid is inadequate, firstly check that there is
fluid in the reservoir: see “Checking fluid levels” in this
chapter).
Then check that the nozzle holes are not clogged; use a
needle to unblock them if necessary.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 199

200
BODY AND UNDERBODY
WARRANTY
Your car is covered by warranty against perforation due
to rust of any original element of the structure or body.
For the general terms of this warranty, refer to the
Warranty Booklet.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
BODYWORK
PROTECTION FROM ATMOSPHERIC
AGENTS
The main causes of corrosion are the following:
❒atmospheric pollution;
❒salty air and humidity (coastal areas, or hot humid
climates);
❒seasonal environmental conditions.
The abrasive action of wind-borne atmospheric dust and
sand, as well as mud and gravel raised by other cars is
also not to be underestimated.
Abarth has used the best manufacturing technologies on
your car to effectively protect the bodywork against
corrosion.
These include:
❒painting products and systems which give the car
particular resistance to corrosion and abrasion;
❒use of galvanised (or pretreated) steel sheets, with
high resistance to corrosion;
❒spraying the underbody, engine compartment,
internal wheel housing parts and other parts with
highly protective wax products;
❒spraying of protective plastic material in the more
exposed points: underdoor, inner mudguard parts,
edges, etc...
❒Use of “open” boxed sections to prevent
condensation and pockets of moisture which could
cause rust inside.
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 200

201
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Detergents pollute the environment. The
vehicle should be washed in areas
equipped for collecting and cleaning the
liquid used in the washing process.
ADVICE FOR PRESERVING THE BODYWORK
Paint
Paintwork does not only serve an aesthetic purpose, but
also protects the underlying sheet metal.
Touch up abrasions and scratches immediately to
prevent rust formation. Use only original paint products
for touch-ups (see “Bodywork paint identification plate”
in the “Technical specifications” section).
Normal maintenance of paintwork consists in washing
the car: the frequency depends on the conditions and
environment where the car is used. For example, in
highly polluted areas, or if the roads are sprayed with
salt, it is wise to wash the car more frequently.
To correctly wash the vehicle, proceed as follows:
❒remove the aerial from the roof to prevent damage
to it if the car is washed in an automatic system;
❒rif high pressure water jets are used to wash the car,
make sure they are at least 40 cm away from the
bodywork to avoid causing damage. It should be
remembered that a build up of water could cause
damage, in the long term, to the car; dy using a low
pressure jet of water;
❒wipe a sponge with a slightly soapy solution over the
bodywork, frequently rinsing with the sponge;
❒rinse well with water and dry with a jet of air or a
chamois leather.Dry the less visible parts, such as the door frames,
bonnet and the headlight frames with special care, as in
these areas water may stagnate more easily. The car
should not be taken to a closed area immediately, but
left outside so that residual water can evaporate.
Do not wash the car after it has been left in the sun or
with the bonnet hot: this may alter the shine of the
paintwork. Exterior plastic parts must be cleaned in the
same way as the rest of the car.
Where possible, do not park under trees; the resinous
substance that many species release give the paint a dull
appearance and increase the possibility of triggering
rusting processes.
IMPORTANT Bird droppings must be washed off
immediately and thoroughly as the acid they contain is
particularly aggressive.
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 201

202
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
INTERIORS
Periodically check that water is not trapped under the
mats (due to water dripping off shoes, umbrellas, etc.)
which could cause oxidisation of the sheet metal. Glasses
To clean glasses, use specific window cleaner products.
Also use clean cloths to avoid scratching the glass or
altering the transparency.
IMPORTANT Wipe the rear window inside gently with
a cloth in the direction of the filaments to avoid
damaging the heating device.
Engine compartment
Wash the engine compartment thoroughly at the end of
every winter. Be careful not to direct the jet of water
onto electronic control units. Adequately protect the
upper air vents to prevent damage to the windscreen
wiper motor. Have this operation performed at a
specialised workshop.
IMPORTANT The washing should take place with the
engine cold and the ignition key in the STOP position.
After the washing operation, make sure that the various
protections (e.g. rubber caps and guards) have not been
removed or damaged.
Front headlights
IMPORTANT Never use aromatic substances (e.g.: petrol)
or ketenes (e.g.: acetone) for cleaning front headlight plastic
lens.
Never use flammable products, such as
petrol ether or rectified petrol to clean
the inside of the car. The electrostatic charges
which are generated by rubbing during the
cleaning operation may cause a fire.
WARNING
Do not keep aerosol cylinders in the
vehicle: risk of bursting. Aerosol cylinders
must not be exposed to a temperature
exceeding 50°C. When the car is exposed to
sunlight, the internal temperature can greatly
exceed this value.
WARNING
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 202

203
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SEATS AND FABRIC PARTS
Remove dust with a soft brush or a vacuum cleaner. It is
advisable to use a moist brush on velvet upholstery.
Rub the seats with a sponge moistened with a solution
of water and neutral detergent.
The fabric upholstery of your car is
designed to withstand normal wear and
tear for a long time. Some precautions
are however needed. Avoid prolonged rubbing
against clothing accessories, such as metal
buckles, Velcro strips and the like, which by
applying a high pressure on the fabric in a small
area could cause the breakage of some threads
and damage the upholstery.
LEATHER SEATS
(for versions/markets where provided)
Remove the dry dirt with a buckskin or slightly damp
cloth, without exercising too much pressure.
Remove any liquid or grease stains using an absorbent
dry cloth, without rubbing. Then clean with a soft cloth
or buckskin cloth dampened with water and neutral
soap.
If the stain persists, use specific products and observe
the instructions carefully.
IMPORTANT Never use alcohol. Make sure that the
cleaning products used contain no alcohol or alcohol
derivatives, even in small quantities.
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 203

204
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAL LEATHER STEERING
WHEEL/GEAR LEVER KNOB
These components must be cleaned with mild soap and
water only.
Never use alcohol and/or alcohol-based products.
Before using off-the-shelf products designed for cleaning
vehicle interiors, make sure that they do not contain
alcohol and/or alcohol-based substances.
If window cleaner accidentally drips onto the steering
wheel or gear lever knob, wipe away immediately and
then wash the affected area with mild soap and water.
IMPORTANT Be careful when using a steering wheel
lock device, where applicable, to prevent damaging the
leather upholstery by rubbing. INTERIOR PLASTIC PARTS
It is advisable to clean interior plastic parts with a
microfibre cloth, if possible, moistened with a solution
of water and non-abrasive mild soap.
Use specific products for cleaning plastic, without
solvents and specifically designed to prevent damage to
the appearance and colour of the treated parts to
remove grease and tough stains.
Remove dust using a microfibre cloth, if necessary
moistened with water. The use of paper tissues is not
recommended as these may leave residues.
IMPORTANT Never use alcohol, petrols and derivatives
to clean the instrument panel lens.
183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 204

205
F0U180Abfig. 176
H Maximum allowed weight on second axle (rear)
I Engine type
L Bodywork version code
M Number for spare parts
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA
We recommend taking note of the identification codes.
The following identification codes are printed and
shown on the plates:
❒Vehicle identification number (VIN) plate.
❒Chassis marking.
❒Bodywork paint identification plate.
❒Engine marking.
IDENTIFICATION DATA PLATE
fig. 176
The data plate is located on the left side of the boot
floor and it bears the following identification data:
B Type-approval number
C Vehicle type identification code
D Chassis number
E Maximum authorised weight of vehicle fully laden
F Maximum authorised weight of vehicle fully laden
plus trailer.
G Maximum permitted weight on first (front) axle
205-220 PUNTO Abarth GB 1ed 17-07-2012 13:26 Pagina 205

206
F0U181Abfig. 177F0U182Abfig. 178
CHASSIS MARKING fig. 178
This is printed on the passenger compartment floor,
near the front right seat.
❒vehicle model;
❒chassis serial number.
ENGINE MARKING
This is stamped onto the cylinder block and shows the
type and the manufacture serial number. BODYWORK PAINT IDENTIFICATION
PLATE fig. 177
The plate is applied on the external tailgate post (left
side) and it bears the following data:
A Paint manufacturer
B Colour name
C Colour code
D Respray and touch-up colour code
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
205-220 PUNTO Abarth GB 1ed 17-07-2012 13:26 Pagina 206