ESP Abarth Punto Evo 2011 Owner handbook (in English)

142
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
ABS SYSTEM FAILURE (amber)
Turning the key to the MAR position illuminates
the warning light, but it should switch off after a
few seconds.
The warning light will light up when the system is either
not working or not available. Under these circumstances
the braking system will work as normal without the extra
performance offered by the ABS system. Drive carefully
and contact an Abarth Dealership as soon as possible.
The display will show a dedicated message.
>
EBD FAULT
(red/amber)
Warning lights
xand >lit at the
same time with the engine running
indicate an EBD system failure or that the system is not
available. This may cause premature locking of the rear
wheels in the event of violent braking, causing the car to
swerve. Drive very carefully to an Abarth Dealership to
have the system inspected immediately.
The display will show a dedicated message.> x
ESP SYSTEM FAILURE
(amber)
When the key is turned to the MAR position
the warning light comes on but should go out
after a few seconds.
ESP-ASR system failure
If the warning light does not go out or remains on while
driving, it indicates a fault in the ESP-ASR system. In this
case, contact an Abarth Dealership as soon as possible.
The display shows the dedicated message.
Note Warning light flashing when driving indicates that
the ESP system has intervened.
Hill Holder system fault
(for versions/markets, where provided)
The warning light will turn on when the Hill Holder
system is faulty. In this case, contact an Abarth
Dealership as soon as possible.
The display shows the dedicated message.
á
AIRBAG FAILURE (red)
When the key is turned to the MAR position
the warning light comes on but should go out
after a few seconds.
The warning light stays on constantly if there is a fault in
the air bag system.
The display shows the dedicated message.
¬

149
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TYRE PRESSURE CHECK
(amber)
TYRE PRESSURE LOW (amber)
TYRE PRESSURE UNSUITABLE FOR
SPEED
(amber)
(for versions/markets where provided)
Check tyre pressures
The symbol is shown on the display to indicate the flat
tyre. Should two or more tyres be flat, the display will
show the indications corresponding to each tyre in
sequence.
Restore correct tyre pressures as soon as possible (see
“Cold tyre pressures” in the “Technical specifications”
section).
Tyre pressure low
The symbol is shown on the display if the pressure of
one or more tyres drops below the preset level. In this
way the TPMS system warns the driver that one or
more tyres may be dangerously flat and liable to
puncture.
n
IMPORTANT Do not continue driving with one or
more flat tyres as handling may be compromised. Stop
the car, avoiding harsh braking or steering manoeuvres.
Repair using the dedicated kit (see the “Automatic
Fix&Go quick tyre repair kit” paragraph in the “In an
emergency” section) and contact an Abarth Dealership
as soon as possible.
Tyre pressure unsuitable for speed
Should travelling at a higher speed than 160 km/h be
required, inflate tyres to pressures values specified in
paragraph “Inflation pressures”.
If the TPMS system (where provided) detects that the
pressure of one or more tyres is unsuitable for the
current speed, the symbol will be shown on the display
together with the dedicated message (see paragraph
“Low tyre pressure” in this section) and it will stay on
until the car speed returns within the preset threshold.
IMPORTANT In this case, slow down immediately
because tyre overheating could compromise tyre
performance and durability beyond repair, and may even
make the tyre explode.

CHANGING A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that the
corresponding fuse is intact before changing a bulb.
For the location of fuses, refer to the paragraph “If a
fuse blows” in this section;
❒before changing a bulb check the contacts for
oxidation;
❒burnt bulbs must be replaced by others of the same
type and power;
❒always check the height of the headlight beam after
changing a bulb for safety reasons.
158
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Changes or repairs to the electrical
system (electronic control units) carried
out incorrectly and without due consideration
for the technical specifications of the system
may lead to malfunctioning and generate a fire
hazard.
WARNING
Halogen lamps contain pressurised gas.
If they break, glass fragments could fly
everywhere.
WARNING
F0U135Abfig. 134
CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder, proceed as follows:
❒disconnect A-fig. 134;
❒turn the bottle anticlockwise to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the canister and fit the
transparent tube B in the special compartment.

169
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U156Abfig. 154
BOOT LIGHT fig. 154
To change the bulb, proceed as follows:
❒open the boot;
❒remove the light A by levering on the point shown
by the arrow.
❒open the protective cover B and replace the press-
fitted bulb;
❒re-close the protective cover B over the lens;
❒refit the light A by inserting it in its correct position
firstly on one side and then on the other until it
clicks into place.
F0U159Abfig. 155
REPLACING FUSES
GENERAL INFORMATION
Fuses protect the electric system: they cut in (i.e. they
blow) in the event of a failure or improper action on the
system.
Check the state of the corresponding fuse when a
device does not work: the filament A-fig. 155 must be
intact. If it is, replace the blown fuse with another with
the same amperage (same colour).
B intact fuse;
C fuse with damaged filament.

178
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Battery fluid is poisonous and corrosive:
avoid contact with your skin and eyes.
The battery recharging operation must be
performed in a ventilated place, away from
naked flames or possible sources of sparks to
avoid the risk of explosion and fire.
WARNING
Don’t try to recharge a frozen battery: If
freezing has occurred, the battery should
be checked by skilled personnel to make sure
that the internal elements are not damaged and
that the body is not cracked, with the risk of
leaking poisonous and corrosive acid.
WARNING
JACKING THE CAR
If the vehicle needs to be raised, go to an Abarth
Dealership which is equipped with arm lifts and
workshop lifts.
Lift the car only by positioning the ends of the jack arms
or the workshop lift at the points shown in fig. 163
corresponding to symbols ▼indicated on the side
skirts.
IMPORTANT Take care not to damage the side skirts
when lifting the car with the workshop lift.
fig. 163F0U167Ab

180
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
The power brakes and power steering
will not operate while the vehicle is
being towed. More effort on the brake pedal
and steering wheel will therefore be required.
Do not use flexible cables when towing and
avoid jerky movements. While towing, make
sure not to damage parts in contact with the
car. When towing the vehicle, be sure to respect
the specific rules of the highway code in
relation to the towing device and the behaviour
to maintain on the road.
WARNING
Clean the threaded housing throughly
before fastening the tow ring. Make sure
that the ring is securely fastened before towing
the car.
WARNING
During towing, do not start the engine.
WARNING

181
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Before towing, switch off the steering
lock (see “Starting device” paragraph in
the “Knowing your car” section). The power
brakes and power steering will not operate
while the vehicle is being towed. More effort on
the brake pedal and steering wheel will
therefore be required. Do not use flexible cables
when towing and avoid jerky movements. While
towing, make sure not to damage parts in
contact with the car. Respect the rules of the
highway code when towing the car, specifically
in relation to the towing device and road
conduct.
WARNING
The front and rear tow hooks should be
used only for emergency operations on
the road. You are allowed to tow the car for
short distances using an appropriate device in
accordance with the highway code (a rigid bar),
to move the vehicle on the road in readiness for
towing or transporting via a breakdown vehicle.
Tow hooks MUST NOT be used to tow vehicles
off the road or where there are obstacles and/or
for towing operations using cables or other non-
rigid devices. Respecting the above conditions,
towing must take place with the two vehicles
(one towing, the other towed) aligned as much
as possible along the same centre line.
WARNING

188
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U171Abfig. 167
ENGINE OIL fig. 167
Check the oil level a few minutes (about five) after the
engine has stopped, with the car parked on level ground.
Check that the level is within the MIN and MAX marks
on the dipstick B.
The range between the MIN. and MAX. marks
corresponds to about 1 litre of oil.
If the oil level is near or under the MIN line, add oil
through the filler A until it reaches the MAX line.
The oil level should never exceed the MAX line.ENGINE OIL CONSUMPTION
The maximum engine oil consumption is usually 400
grams every 1000 km.
When the car is new, the engine needs to run in,
therefore the engine oil consumption can only be
considered stabilised after the first 5,000 - 6,000 km.
IMPORTANT The oil consumption depends on driving
style and the car usage conditions.
IMPORTANT After adding or changing the oil, let the
engine run for a few seconds and wait a few minutes
after switching it off before checking the level.
When the engine is hot, take care when
working inside the engine compartment
to avoid burns. Remember that when the engine
is hot, the fan may operate: danger of injury.
Pay attention to scarves, ties and other loose
fitting garments: they may get caught by moving
components.
WARNING
Do not add any oil with different
specifications to those of the existing
engine oil.

206
F0U181Abfig. 177F0U182Abfig. 178
CHASSIS MARKING fig. 178
This is printed on the passenger compartment floor,
near the front right seat.
❒vehicle model;
❒chassis serial number.
ENGINE MARKING
This is stamped onto the cylinder block and shows the
type and the manufacture serial number. BODYWORK PAINT IDENTIFICATION
PLATE fig. 177
The plate is applied on the external tailgate post (left
side) and it bears the following data:
A Paint manufacturer
B Colour name
C Colour code
D Respray and touch-up colour code
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS

212
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
UNDERSTANDING RIM MARKING fig. 179
Example: 7J x 17 ET39
7 = rim width in inches 1.
J = rim drop centre outline (side projection
where the tyre bead rests)
2.
17 = rim nominal diameter in inches (corresponds
to diameter of the tyre to be mounted)
3= Ø.
ET39 = wheel camber (distance between the disc/rim
support plane and the wheel rim centre line).RIM PROTECTORS fig. 180
DO NOT fit wheel hub caps (for
versions/markets, where provided) when
using integral hub caps fixed (with springs) to
the steel rim and after sale tyres provided with
Rim Protector. The use of unsuitable tyres and
wheel hub caps could cause a sudden pressure
loss in the tyre.
WARNING
F0U195Abfig. 180