Acura CL 2003 Owner's Manual

The shif t lever has nine positions. It
must be in Park or Neutral to start
the engine. When you are stopped in
D,D,D,2,1,N,R,orthe
Sequential SportShif t mode, press
f irmly on the brake pedal and keep
your f oot of f the accelerator pedal.To select the Sequential SportShif t
mode, slide the shif t lever toward the
lef t f rom the ‘‘D ’’ position.
In this mode the shif t lever allows
youtoshiftupanddownmanually.
YoucannotshiftoutofParkwiththe
brake pedal depressed when the
ignition switch is in LOCK (0) or
ACCESSORY (I). Whenever you move the shif t lever,
slide it along the guide on the
console.
543 5
To shift from:
PtoR
RtoN
NtoD
DtoD
DtoD Dto22to1
1to2
2toD
DtoD
DtoD DtoN NtoRRtoP Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
5
54
43 3
3
34
45 5
Shif t L ever Positions
Automatic Transmission
Driving198
S SH H I
IFFT T L
LE
E V
V E
ER
R
S
SE EQ
QU UEEN
NT TI
IAA L
L
S
SP PO
OR RTTS
SH H I
IFFT T
M
M O
ODDE
E
P
P O
OS SIITT I
IOON N

µµ
µµ
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Move the shif t
lever to the right to shif t out of the
Park position.
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. To shif t to Reverse
f rom Park, see the explanation under
Park. To shif t to Reverse f rom
Neutral, come to a complete stop and
then shift.
If you have done all of the above and
still cannot move the lever out of
Park, see Shif t Lock Release on page . Your car has a reverse lockout so
you cannot accidentally shif t to
Reverse from Neutral or any other
driving position when the vehicle
speed exceeds 7 9 mph (12 14
km/h).
If you cannot shif t to Reverse when
the car is stopped, press the brake
pedal and slowly shif t to Neutral, and
then to Reverse.
If there is a problem in the reverse
lockout system, or your car’s battery
is disconnected or goes dead, you
cannot shif t to Reverse. (Ref er to
Shif t Lock Release on page ).
204
204
CONT INUED
Park (P)Reverse (R)
Automatic Transmission
Driving199

µ
µ µ
´
´
µ
µ
Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to Park posi-
tion if you need to leave the car for
any reason. Press on the brake pedal
when you are moving the shif t lever
f rom Neutral to another gear.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear for your speed and
acceleration. You may notice the
transmission shif ting up at higher
speeds when the engine is cold. This
helps the engine warm up f aster. With
the shif t lever in ‘‘D ’’ position, you
can select the Sequential SportShif t
mode to shif t gears; much like a
manual transmission, but without a
clutch pedal.
Even with the Sequential SportShift
Mode selected, the transmission will
automatically upshif t and downshif t
between f irst and second gear.
To enter the Sequential SportShif t
mode, move the shif t lever to the lef t.
To return to ‘‘D ’’, move the shif t
lever to the right.
When you move the shif t lever f rom
‘‘D ’’ to the Sequential SportShift
mode, the display shows the selected
gear.
In the Sequential SportShif t mode,
each time you push f orward on the
shif t lever, the transmission shif ts to
a higher gear. Pull back on the lever
to downshif t. The number of the
gear selected is displayed next to the
‘‘D ’’ indicator (see page ).
197
5
5
5
5
Neutral (N)
Drive (D )
5
Sequent ial Sport Shif t Mode
Automatic Transmission
Driving200
D D o
ow
wn ns
shh i
iff t
t
U
Up
ps
shh i
iff t
t

à
à
à
à
When you accelerate away f rom a
stop, the transmission will start in
first gear and then automatically
upshif t to second gear. You have to
manually upshif t between second
and f if th gears. Make sure you
upshif t bef ore the engine speed
reaches the tachometer’s red zone.
The transmission remains in the
selected gear (5, 4, 3). There is no
automatic downshif t when you push
the accelerator pedal to the floor.
The transmission may automatically
downshif t f rom the higher gear to
the lower gear under the f ollowing
conditions:
To shift from 43
54 Speed range
under 18 mph
(29 km/h)
under 34 mph
(55 km/h)
To shift from 43
54 Speed range
under 34 mph
(55 km/h)
under 47 mph
(75 km/h) Downshif ting gives you more power
when climbing or provides engine
braking when going down a steep hill.
The transmission will also shif t
automatically as the vehicle comes to
a complete stop. It will downshif t to
f irst gear when the vehicle speed is
under 9 mph (15 km/h).
If you try to manually downshif t at a
speed that would cause the engine to
exceed the redline in a lower gear,
the transmission will not downshif t.
Thegearindicatorwillflashthe
numberof thelowergearseveral
times, then return to the higher gear.
Driving uphill Driving on level roads and downhill
CONT INUED
Driving
Automatic Transmission
201

µµ
à
à
à à
à
à
Î
Î
Î
Î
Î
Î
If the car speed slows to below the
redline of the selected lower gear
position while the indicator is
f lashing, the transmission will
downshif t and the display will show
the selected lower gear.
If the transmission temperature is
below 14 °F ( 10 °C), you may not
be able to use the Sequential
SportShif t mode. These positions
are similar to D , except when you
select the D position, only the f irst
f our gears are selected. When you
select D , only the f irst three gears
are selected. D can also keep the
transmission f rom cycling between
fourth and fifth gears in stop-and-go
driving, and D can keep the
transmission f rom cycling between
third and f ourth gears.
Use D when towing a trailer in hilly
terrain, or to provide engine braking
when going down a steep hill. D
gives you more power and increased
engine braking.
The table shows the speed ranges
f or upshif ting and downshif ting.
To shift from 23
34
45 Speed range
over 9 mph
(15 km/h)
over 18 mph
(29 km/h)
over 34 mph
(55 km/h) Speed range
under 60 mph
(96 km/h)
under 65 mph
(104 km/h)
under 93 mph
(150 km/h)
under 104 mph
(166 km/h)
under 125 mph
(200 km/h)
To shift from
32
43
54
5
4
3 4
3
3 3
1:
2: Premium model
Type-S
1
2
1
2
Drive(D,D)43
Automatic Transmission
Driving202

µµ
ForfasteraccelerationwheninD ,
D or D , you can get the
transmission to automatically
downshif t by pushing the accelerator
pedal to the f loor. The transmission
will shif t down one or two gears,
depending on your speed.
This position locks
the transmission in second gear. It
does not downshif t to f irst gear
when you come to a stop. Second
gives you more power when climbing,
and increased engine braking when
going down steep hills. Use second
gear when starting out on a slippery
surf ace or in deep snow. It will help
reduce wheelspin. With the lever in this
position, the transmission locks in
First gear.
If you shif t into First position when
the vehicle speed is above 31 mph
(50 km/h), the transmission shif ts
into Second gear f irst to avoid
sudden engine braking. If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
RPM below the red zone.
3
45
Second (2) First (1)
Engine Speed L imiter
Automatic Transmission
Driving203

If you need to use the Shif t Lock
Release, it means your car is
developing a problem. Have the car
checked by your Acura dealer.
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
is also used to release the Reverse
Lockout.
Insert a screwdriver in the Shif t
Lock Release slot.
Push down on the screwdriver and
move the shift lever out of Park to
Neutral.
To release the Reverse Lockout,
move the shift lever from Neutral
to Reverse, then to Park.Remove the screwdriver f rom the
Shif t Lock Release slot, then
reinstall the cover. Make sure the
notchonthecoverisontheright
side. Depress the brake pedal and
restart the engine.
Set the Parking brake.
Make sure the ignition switch is in
the OFF (0) position.
To release the Reverse Lockout,
make sure the ignition switch is in
the ACCESSORY (I) position.
Put a cloth on the edge of the Shif t
Lock Release slot cover next to
the shift lever.
Use a small flat-tipped screwdriver
or small metal plate (neither are
included in the tool kit) to remove
the cover. Caref ully pry on the
edge of the cover.
1.
2.
3.
4.
5.
6.
Shif t L ock Release
Automatic Transmission
Driving204
S SH
H I
IFFT T L
LOOC CKK R
REEL
LEE A
A S
SEE S
SLLOOT T
C
CO OV VE
ER
R

µMake sure the moonroof and the
windows are closed.
Place any packages, valuables, etc.,
in the trunk or take them with you. Turn of f the lights.
Lockthedoorswiththekeyorthe
remote transmitter. Check the
indicator on the driver’s door to
verify that the security system is
set.
Never park over dry leaves, tall
grass, or other f lammable
materials. The three way catalytic
converter gets very hot, and could
cause these materials to catch on
fire.
Always use the parking brake when
you park your car. The indicator on
the instrument panel shows that the
parking brake is not f ully released; it
does not indicate that the parking
brakeisfirmlyset.Makesurethe
parking brake is set f irmly or your
car may roll if it is parked on an
incline.
If your car has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park.Thiskeepsthecarfrom
moving and putting pressure on the
parking mechanism in the
transmission making it easier to
move the shift lever out of Park
when you want to drive away.
If the car is f acing uphill, turn the
f ront wheels away f rom the curb. If
you have a manual transmission, put
it in f irst gear.
If the car is f acing downhill, turn the
f ront wheels toward the curb. If you
have a manual transmission, put it in
reverse gear.
Make sure the parking brake is f ully
released bef ore driving away.
Driving with the parking brake
partially set can overheat or damage
the rear brakes.
Parking T ips
Parking
Driving205

Your Acura is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The ABS helps
you retain steering control when
braking very hard.
Put your f oot on the brake pedal only
when you intend to brake. Resting
your f oot on the pedal keeps the
brakes applied lightly, causing them
to build up heat. Heat build-up can
reduce how well your brakes work. It
also keeps your brake lights on all
the time, conf using drivers behind
you.Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by downshif ting to a lower
gear and taking your f oot of f the
accelerator pedal.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Since a
longer distance is needed to stop
with wet brakes, be extra cautious
and alert in your driving.
All f our brakes have audible brake
wear indicators.
When the brake pads need replacing,
you will hear a distinctive metallic
‘‘screeching’’ sound when you apply
the brakes. If you do not have the
brake pads replaced, they will begin
screeching all the time.
Your brakes may sometimes squeal
or squeak when you apply them
lightly. Do not conf use this with the
brakewearindicators.Theymakea
very audible ‘‘screeching.’’ Brake Wear Indicators
The Braking System
Driving206

this defeats the
purpose of the ABS. Let the ABS
work f or you by always keeping f irm,
steady pressure on the brake pedal
as you steer away from the hazard.
This is sometimes ref erred to as
You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal; it is the ABS rapidly
pumping the brakes.
Activation varies with the amount of
traction your tires have. On dry
pavement, you will need to press on
thebrakepedalveryhardbeforeyou
activate the ABS. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
Your car has an Anti-lock Brake
System (ABS) as standard
equipment. ABS helps to prevent the
wheels f rom locking up and skidding
during hard braking, allowing you to
retain steering control.
When the f ront tires skid, you lose
steering control; the car continues
straightaheadeventhoughyouturn
the steering wheel. The ABS helps to
prevent lock-up and helps you retain
steering control by pumping the
brakes rapidly; much f aster than a
person can do it.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the car (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.
‘‘stomp and steer.’’
CONT INUED
Brake System Design
A nti-lock BrakesYou should never pump the
brake pedal;
The Braking System
Driving207
F F r
roo n
nt
t