ignition ACURA CSX 2006 Service Repair Manual


Î
(#'
 )
Removal Installation
24-191
Side Airbag Replacement
AB
A
B
6.3 N·m
(0.64 kgf·m, 4.65 lbf·ft)
NOTE: If replacing the side airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the seat assembly (see page 20-118) and seat-back cover (see page 20-123).
3. Remove the mounting screws (A) and the side airbag (B). NOTE:
 If the side airbag lid is secured by tape, remove the tape.
 Do not open the lid of the side airbag cover.
 Use new mounting screws tightened to the specified torque. When you replace a side airbag, make sure
that the seat-back cover is installed properly.
Improper installation may prevent proper
deployment.
 Be sure to install the harness wires so that they are not pinched or interfering with other parts.
1. Place the side airbag on the seat-back frame (A). Install new side airbag mounting screws (B).
2. Install the seat-back cover in the reverse order of removal (see page 20-123).
3. Install the seat assembly (see page 20-118).
4. Move the front seat and the seat-back through their full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Do the battery terminal reconnection procedure (see page 22-68).
6. Clear any DTCs (see page 24-23).
7. After installing the side airbag, confirm proper system operation: Turn the ignition switch to ON
(II); the SRS indicator should come on for about
6 seconds and then go off.
Replace.
08/08/21 14:01:56 61SNR030_240_0191
ProCarManuals.com
DYNOMITE -2009-


24-195
A
2. Connect the side curtain airbag 2P connector (A) to the floor wire harness.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTCs (see page 24-23).
5. After installing the side curtain airbag, confirm proper system operation: Turn the ignition switch to ON (II); theSRS indicator should come on for about 6 seconds and then go off.
6. Install all removed parts.
7. Confirm proper headliner/pillar trim overlap (see page 24-187).
Left side shown; right side is similar.
08/08/21 14:01:57 61SNR030_240_0195
ProCarManuals.com
DYNOMITE -2009-

Î


Î
(#'
!)
Special Tools Required
Driver’s Airbag
Front Passenger’s Airbag
Side Airbag
Side Curtain Airbag
Deploying Airbags in the Vehicle
24-196
SRS
Airbag and Tensioner Disposal
A
B
A
A
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, side curtain
airbags, seat belt tensioners, or seat belt buckle
tensioner (including those in a whole vehicle to be
scrapped), the part(s) must be deployed. If the vehicle is
still within the warranty period, the Honda District Parts
and Service Manager must give approval and/or special
instructions before deploying the part(s). Only after the
part(s) have been deployed (as the result of vehicle
collision, for example), can they be scrapped.
If the parts appear intact (not deployed), treat them with
extreme caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, side curtain airbags, seat belt
tensioners, and seat belt buckle tensioner should be
deployed while still in the vehicle. These parts should
not be considered as salvageable parts and should
never be installed in another vehicle.1. Turn the ignition switch to LOCK (0), then disconnect the negative cable from the battery,
then wait at least 3 minutes before starting work.
2. Confirm that each airbag, side airbag, side curtain airbag, seat belt tensioner, or seat belt buckle
tensioner is securely mounted.
3. Confirm that the deployment tool is functioning properly by following the check procedure on the
tool label.
4. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel. 5. Remove the glove box, then disconnect the front
passenger’s airbag 4P connector (A) from the
dashboard wire harness.
6. Disconnect the side airbag 2P connector (A) from the floor wire harness.
7. Disconnect the floor wire harness 2P connector from the side curtain airbag (A).
08/08/21 14:01:58 61SNR030_240_0196
ProCarManuals.com
DYNOMITE -2009-



24-202SRS
Cable Reel Replacement (cont’d)
A
D
B
A C A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
5. Install the steering column covers.
6. If necessary, center the cable reel (new
replacement cable reels come centered). Do this by
first rotating the cable reel clockwise until it stops.
Then rotate it counterclockwise (about three turns)
until the arrow mark (A) on the cable reel label
points straight up.
7. Position the two tabs (A) of the turn signal canceling sleeve (B) as shown, and install the
steering wheel on to the steering column shaft,
making sure the steering wheel hub (C) engages
the pins (D) of the cable reel and tabs of the turn
signal canceling sleeve. Do not tap on the steering
wheel or steering column shaft when installing the
steering wheel. 8. Install a new steering wheel bolt (A), then
reconnect the connectors.
9. Install the driver’s airbag (see page 24-188).
10. Do the battery terminal reconnection procedure (see page 22-68).
11. Clear any DTCs (see page 24-23).
12. After installing the cable reel, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 After the SRS indicator has turned off, turn the steering wheel fully left and right to confirm the
SRS indicator does not come on.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel switches work properly.
Replace.
08/08/21 14:02:00 61SNR030_240_0202
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal Installation
24-203
SRS Unit Replacement
C
A B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
C
NOTE: If you are disconnecting only SRS unit connector
A, skipstep 2. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Disconnect both seat belt tensioner connectors (see page 24-21) and both seat belt buckle
tensioner connectors (see page 24-21).
3. Remove the center console (see page 20-92).
4. Disconnect SRS unit connector A (28P), B (28P) and remove the TORX bolts (C), then pull out the SRS
unit. 1. Install the SRS unit (A) with new TORX bolts (B),
then connect the connectors (C) to the SRS unit;
push them into position until they click.
NOTE: Be sure the SRS unit is sitting squarely
against its bracket before torquing the TORX bolt.
2. Reconnect both seat belt tensioner connectors (see page 24-21) and both seat belt buckle
tensioner connector (see page 24-21).
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Calibrate the ODS unit (see page 24-27).
5. Do the ODS unit operation check (see page 24-28).
6. Confirm proper SRS operation: Turn the ignition switch to ON (II); the SRS indicator should come on
for about 6 seconds and then go off.
7. Reinstall all removed parts.
Replace.
08/08/21 14:02:01 61SNR030_240_0203
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'

 )
Removal Installation
24-204SRS
Side Impact Sensor (First) Replacement
A
C B
B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
C
NOTE: Review the seat replacement procedure
(see page 20-118) before doing repairs or service. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the front seat assembly (see page 20-118).
3. Remove the front door sill inner trim (see page 20-66).
4. Remove the lower B-pillar lower trim panel (see page 20-69).
5. Disconnect the floor wire harness 4P connector (A) from the side impact sensor (first) (B).
6. Using a TORX T30 bit, remove the TORX bolt (C), then remove the side impact sensor (first). 1. Install the side impact sensor (first) (A) with a new
TORX bolt (B), then connect the floor wire harness
4P connector (C) to the side impact sensor (first).
2. Do the battery terminal reconnection procedure (see page 22-68).
3. Reinstall all removed parts.
4. Clear any DTCs (see page 24-23).
5. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
Replace.
08/08/21 14:02:01 61SNR030_240_0204
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
(#'

 )
Removal Installation
24-205
Side Impact Sensor (Second) Replacement
A
C B
B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
C
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the rear seat and seat side bolster (see page 20-131).
3. Disconnect the floor wire harness 2P connector (A) from the side impact sensor (second) (B).
4. Remove the TORX bolt (C) using a TORX T30 bit, then remove the side impact sensor (second). 1. Install the side impact sensor (second) (A) with a
new TORX bolt (B) then connect floor wire harness
2P connector (C) to the side impact sensor (second).
2. Do the battery terminal reconnection procedure (see page 22-68).
3. Clear any DTCs (see page 24-23).
4. Reinstall all removed parts.
5. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
Replace.
08/08/21 14:02:01 61SNR030_240_0205
ProCarManuals.com
DYNOMITE -2009-

Î

(#'
 )
Removal Installation
24-206SRS
Rear Safing Sensor Replacement
A
C
B
A
B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
1. Do the battery terminal disconnection procedure
(see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the rear seat (see page 20-131).
3. Disconnect the floor wire harness 2P connector (A) from the rear safing sensor (B).
4. Using a TORX T30 bit, remove the TORX bolt (C), then remove the rear safing sensor. 1. Install the rear safing sensor (A) with a new TORX
bolt (B) then connect the floor wire harness 2P
connector (C) to the rear safing sensor.
2. Do the battery terminal reconnection procedure (see page 22-68).
3. Clear any DTCs (see page 24-23).
4. Reinstall all removed parts.
5. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
Replace.
08/08/21 14:02:02 61SNR030_240_0206
ProCarManuals.com
DYNOMITE -2009-


Î
24-208SRS
Front Passenger’s Weight Sensor Replacement (cont’d)
A
42 N·m
(4.2 kgf·m, 30 lbf·ft)
07744-0010300
MORE THAN
4mm(0.2in.)
A
B B B
B
3. Insert the special tool into the hole in the cushion frame to position the spring washers, then tighten
the TORX nuts (A). Begin with , and tighten them
in crisscross pattern in two or more steps.
4. Using the pin driver to position the spring washer’s, torque the TORX nuts in the sequence shown in
two or more steps. 5. Make sure the gap between the spring washer (A)
and the seat track (B) is more than 4 mm (0.2 in.) as
shown.
6. Reassemble the front passenger’s seat cushion cover/pad (see page 20-127).
7. Reinstall the front passenger’s seat (see page 20-118).
8. Do the battery terminal reconnection procedure (see page 22-68).
9. Calibrate the ODS unit (see page 24-27).
10. Clear any DTCs (see page 24-23).
11. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
08/08/21 14:02:03 61SNR030_240_0208
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal Installation
24-209
ODS Unit Replacement
B
AC
D
D
CA
B
NOTE: Review the seat replacement procedure
(see page 20-118) before doing repairs or service.
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the passenger’s seat assembly (see page 20-118) and seat-back cover (see page 20-127).
3. Disconnect the ODS unit 18P connector (A) and OPDS sensor connectors (B) from the ODS unit (C).
4. Remove the two nuts (D) and the ODS unit. 1. Place the ODS unit (A) on the seat-back frame.
Tighten the two nuts (B), and connect the ODS unit
harness 18P connector (C) and OPDS sensor
connectors (D) to the ODS unit.
2. Install the seat-back cover in the reverse order of removal.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Set the seat-back in the normal position, and make sure there is nothing on the front passenger’s seat.
5. Initialize the ODS unit (see page 24-26).
6. Clear any DTCs (see page 24-23).
7. Confirm proper system operation: Turn the ignition switch to ON (II); the SRS indicator should come on
for about 6 seconds and then go off.
08/08/21 14:02:03 61SNR030_240_0209
ProCarManuals.com
DYNOMITE -2009-