Engine air ACURA CSX 2006 Service Repair Manual

(#' 
)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0507:
YES
NO
YES
NO YES
NO
YES
NO
11-300Idle Control System
DTC Troubleshooting (cont’d)
Idle Control System RPM Higher
Than Expected
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle for at least 20 seconds.
4. Monitor the OBD STATUS for DTC P0507 in the DTCs MENU with the HDS.
Go to step 5.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. If the screen
indicates EXECUTING, keep idling until a result
comes on. If the screen indicates OUT OF
CONDITION, recheck with different load conditions
(electrical, A/C, gear position, etc.), then go to
step 3.
5. Check for vacuum leaks at these parts:  PCV valve
 PCV hose
 EVAP canister purge valve
 Throttle body
 Intake manifold
 Brake booster hose
 Brake booster
Repair or replace the leaking part(s), then go
to step 6.
Go to step 6. 6. Turn the ignition switch to ON (II).
7. Reset the ECM/PCM with the HDS.
8. Do the ECM/PCM idle learn procedure (see page
11-310).
9. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle for at least 20 seconds.
10. Check for Temporary DTCs or DTCs with the HDS.
Go to step 12.
Go to step 11.
11. Monitor the OBD STATUS for DTC P0507 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 10,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the throttle body
and the ECM/PCM, then go to step 1. If the screen
indicates EXECUTING, keep idling until a result
comes on. If the screen indicates OUT OF
CONDITION, recheck with different load conditions
(turn on the headlights, blower motor, or A/C;
change the gear position, etc.), then go to step 9.
Does t he scr een i nd i cat e F AILE D?
Ar e t her e any l eak s? Is DT C P0507 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:28:31 61SNR030_110_0300
ProCarManuals.com
DYNOMITE -2009-

µ
µ µ
µ
YES
NO YES
NO
11-305
SG6 (BLK)
ECM/PCM CONNECTOR A (44P) A/C PRESSURE SENSOR 3P CONNECTOR
SG6 (BLK)
18. Turn the ignition switch to LOCK (0).
19. Jump the SCS line with the HDS.
20. Disconnect ECM/PCM connector A (44P).
21. Check for continuity between A/C pressure sensor3P connector terminal No. 3 and ECM/PCM
connector terminal A9.
Go to step 32.
Repair open in the wire between the ECM/
PCM (A9) and the A/C pressure sensor, then go to
step 24. 22. Turn the ignition switch to LOCK (0).
23. Replace the A/C pressure sensor (see page 21-8).
24. Reconnect all connectors.
25. Turn the ignition switch to ON (II).
26. Reset the ECM/PCM with the HDS.
27. Do the ECM/PCM idle learn procedure (see page
11-310).
28. Start the engine, and let it idle.
29. Turn the blower switch on.
30. Turn the A/C switch on.
31. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/C pressure sensor and the ECM/
PCM, then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
32. Reconnect all connectors.
33. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
34. Start the engine, and let it idle.
35. Turn the blower switch on.
36. Turn the A/C switch on.
(cont’d)
Wire side of female terminalsTerminal side of female terminals
Is there continuity? Is DT C P0533 ind icated ?
08/08/21 14:29:36 61SNR030_110_0305
ProCarManuals.com
DYNOMITE -2009-

(#'



)
µ
µµ µ
µ
µ
µ
µ
YES
NO YES
NO
YES
NO
YES
NO
11-30611-306Idle Control System
DTC Troubleshooting (cont’d) A/C Signal Circuit Troubleshooting
37. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/C pressure sensor and the ECM/
PCM. If the ECM/PCM was updated, substitute a
known-good ECM/PCM (see page 11-7), then go to
step 34. If the ECM/PCM was substituted, go to step
1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting. 1. Start the engine, and let it idle.
2. Turn the blower switch on.
3. Turn the A/C switch on.
4. Check the A/C CLUTCH in the DATA LIST with the
HDS.
Go to step 5.
Do the A/C system test (see page 21-99).
5. Check the A/C system.
The air conditioning system circuit is OK.
Go to step 6.
6. Turn the ignition switch to LOCK (0).
7. Turn the ignition switch to ON (II).
8. Activate the A/C CLUTCH in the INSPECTION MENU with the HDS.
Do the A/C system test (see page 21-99).
Go to step 9.
9. Turn the ignition switch to LOCK (0).
10. Jump the SCS line with the HDS.
11. Disconnect ECM/PCM connector A (44P).
12. Turn the ignition switch to ON (II).
Is DT C P0533 ind icated ?
Does it indicate ON?
Does t he A/ C sy st em oper at e?
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch?
08/08/21 14:29:36 61SNR030_110_0306
ProCarManuals.com
DYNOMITE -2009-



(#'


)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-30711-307
Alternator FR Signal Circuit
Troubleshooting
ECM/PCM CONNECTOR A (44P)
ACC (RED)JUMPER WIRE
ECM/PCM CONNECTOR B (44P)ALTF
(WHT/RED)
13. Momentarily connect ECM/PCM connector terminalA14 to body ground with a jumper wire s everal
times.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Check for poor connections or loose terminals
attheA/CclutchrelayandtheECM/PCM.Ifthe
connections and the terminals are OK, check the
A/C compressor clutch relay (see page 22-70),
repair open in the wires between the ECM/PCM
(A14), the A/C compressor clutch relay, and other
A/C systems parts. 1. Start the engine, and let it idle.
2. Monitor the ALTERNATOR in the DATA LIST with
the HDS.
3. Check if the indicated percentage varies when the headlight switch is turned on.
The alternator signal circuit is OK.
Go to step 4.
4. Turn the headlight switch and ignition switch to LOCK (0).
5. Jump the SCS line with the HDS.
6. Disconnect the alternator 4P connector.
7. Disconnect ECM/PCM connector B (44P).
8. Check for continuity between body ground and ECM/PCM connector terminal B43.
Repair short in the wire between the ECM/
PCM (B43) and the alternator.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Terminal side of female terminals
Terminal side of female terminals
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch? Does t he per cent age v ar y ?
Is there continuity?
08/08/21 14:29:37 61SNR030_110_0307
ProCarManuals.com
DYNOMITE -2009-



(#'


)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-30711-307
Alternator FR Signal Circuit
Troubleshooting
ECM/PCM CONNECTOR A (44P)
ACC (RED)JUMPER WIRE
ECM/PCM CONNECTOR B (44P)ALTF
(WHT/RED)
13. Momentarily connect ECM/PCM connector terminalA14 to body ground with a jumper wire s everal
times.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Check for poor connections or loose terminals
attheA/CclutchrelayandtheECM/PCM.Ifthe
connections and the terminals are OK, check the
A/C compressor clutch relay (see page 22-70),
repair open in the wires between the ECM/PCM
(A14), the A/C compressor clutch relay, and other
A/C systems parts. 1. Start the engine, and let it idle.
2. Monitor the ALTERNATOR in the DATA LIST with
the HDS.
3. Check if the indicated percentage varies when the headlight switch is turned on.
The alternator signal circuit is OK.
Go to step 4.
4. Turn the headlight switch and ignition switch to LOCK (0).
5. Jump the SCS line with the HDS.
6. Disconnect the alternator 4P connector.
7. Disconnect ECM/PCM connector B (44P).
8. Check for continuity between body ground and ECM/PCM connector terminal B43.
Repair short in the wire between the ECM/
PCM (B43) and the alternator.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
Terminal side of female terminals
Terminal side of female terminals
I s t her e a cl i ck i ng noi se f r om t he A/ C compr essorclutch? Does t he per cent age v ar y ?
Is there continuity?
08/08/21 14:29:37 61SNR030_110_0307
ProCarManuals.com
DYNOMITE -2009-

(#'

)

¶
¶
¶
¶
¶
¶
Idle speed should be:
K20Z2 engine:
M/T 700 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Idle speed should be:
K20Z2 engine: M/T 780 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Procedure
11-31011-310Idle Control System
Idle Speed Inspection (cont’d) ECM/PCM Idle Learn Procedure
4. Start the engine. Hold the engine speed at
3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check the idle speed without load conditions: headlights, blower fan, radiator fan, and air
conditioner off.
6. Let the engine idle for 1 minute with high electric load (A/C switch on, temperature set to max cool,
blower fan on high, and headlights on high beam).
NOTE: If the idle speed is not within specification,
dotheECM/PCMidlelearnprocedure(seepage
11-310). If the idle speed is still not within
specification, go to the symptom troubleshooting.
7. Reconnect the EVAP canister purge valve connector. The idle learn procedure must be done so the ECM/PCM
can learn the engine idle characteristics.
Do the idle learn procedure whenever you do any of
these actions:
 Replace the ECM/PCM.
 Reset the ECM/PCM.
 Update the ECM/PCM.
 Replace or clean the throttle body.
 Disassemble the engine or the transmission.
NOTE: Erasing DTCs with the HDS does not require you
to do the idle learn procedure.
1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
2. Reset the ECM/PCM with the HDS.
3. Turn the ignition switch to ON (II), and wait 2 seconds.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, or until the
engine coolant temperature reaches 90 °C (194 °F).
5. Let the engine idle for about 5 minutes with the throttle fully closed.
NOTE: If the radiator fan comes on, do not include
its running time in the 5 minutes.
08/08/21 14:29:38 61SNR030_110_0310
ProCarManuals.com
DYNOMITE -2009-

(#'

)

¶
¶
¶
¶
¶
¶
Idle speed should be:
K20Z2 engine:
M/T 700 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Idle speed should be:
K20Z2 engine: M/T 780 50 rpm
A/T 800 50 rpm (in P or N)
K20Z3 engine: M/T 750 50 rpm
Procedure
11-31011-310Idle Control System
Idle Speed Inspection (cont’d) ECM/PCM Idle Learn Procedure
4. Start the engine. Hold the engine speed at
3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check the idle speed without load conditions: headlights, blower fan, radiator fan, and air
conditioner off.
6. Let the engine idle for 1 minute with high electric load (A/C switch on, temperature set to max cool,
blower fan on high, and headlights on high beam).
NOTE: If the idle speed is not within specification,
dotheECM/PCMidlelearnprocedure(seepage
11-310). If the idle speed is still not within
specification, go to the symptom troubleshooting.
7. Reconnect the EVAP canister purge valve connector. The idle learn procedure must be done so the ECM/PCM
can learn the engine idle characteristics.
Do the idle learn procedure whenever you do any of
these actions:
 Replace the ECM/PCM.
 Reset the ECM/PCM.
 Update the ECM/PCM.
 Replace or clean the throttle body.
 Disassemble the engine or the transmission.
NOTE: Erasing DTCs with the HDS does not require you
to do the idle learn procedure.
1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
2. Reset the ECM/PCM with the HDS.
3. Turn the ignition switch to ON (II), and wait 2 seconds.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, or until the
engine coolant temperature reaches 90 °C (194 °F).
5. Let the engine idle for about 5 minutes with the throttle fully closed.
NOTE: If the radiator fan comes on, do not include
its running time in the 5 minutes.
08/08/21 14:29:38 61SNR030_110_0310
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#') K20Z2 engine:
K20Z3 engine:
11-342Intake Air System
Component Location Index
THROTTLE BODY
AIR CLEANER
INTAKE AIR RESONATOR
INTAKE AIR BYPASS CONTROL
THERMAL VALVE ENGINE CONTROL MODULE (ECM)/
POWERTRAIN CONTROL MODULE (PCM)
THROTTLE BODY AIR CLEANER
INTAKE AIR RESONATOR
INTAKE AIR BYPASS CONTROL
THERMAL VALVE ENGINE CONTROL MODULE (ECM)
Test, page 11-343
Cleaning, page 11-344
Removal/Installation, page 11-348
Disassembly/Reassembly, page 11-350 Removal/Installation, page 11-345
Element Inspection/Replacement,
page 11-346
Removal/Installation,page 11-346
Test, page 11-344
Replacement, page 11-351 Update, page 11-227
Substitution, page 11-7
Replacement, page 11-228
Test, page 11-343
Cleaning, page 11-344
Removal/Installation, page 11-348
Disassembly/Reassembly, page 11-350 Removal/Installation, page 11-345
Element Inspection/Replacement,
page 11-346
Removal/Installation,page 11-346
Test, page 11-344
Replacement, page 11-351 Update, page 11-227
Substitution, page 11-7
Replacement, page 11-228
08/08/21 14:31:07 61SNR030_110_0342
ProCarManuals.com
DYNOMITE -2009-


(#'
!) µ

(#') Special Tools Required
11-34411-344 Intake Air System
Throttle Body Cleaning
Intake Air Bypass Control Thermal
Valve Test
A A A
B
Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
1. Check for damage to the air cleaner. If the air cleaner element is damaged, replace it (see page
11-346).
2. Remove the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
3. Clean off the carbon from the throttle valve and inside the throttle body with a paper towel soaked
in throttle plate and induction cleaner.
NOTE: Remove the throttle body to clean it.
 Be careful not to pinch your fingers.
 To avoid removing the molybdenum coating, do not clean the bearing area of the throttle shaft (A).
 Do not spray throttle plate and induction cleaner directly on the throttle body.
 Use Honda genuine throttle plate and induction cleaner.
4. Install the throttle body (see page 11- 348).
5. Reset the ECM/PCM with the HDS (see page 11-4).
6. Turn the ignition switch to ON (II), and wait 2 seconds.
7. Do the ECM/PCM idle learn procedure (see page 11-310). Vacuum pump/gauge, 0 30 in.Hg, Snap-on YA4000A
or equivalent, commercially available
1. Start the engine, then let it idle. NOTE: The engine coolant temperature must be
below 65 °C (149 °F).
2. Remove the engine cover (see step 1 on page 9-3).
3. Remove the vacuum hose (A) from the intake air duct, and connect a vacuum pump/gauge (B) to the
hose.
4. Raise and lower the engine speed, and make sure the vacuum gauge reading changes as the engine
speed changes.
If the vacuum reading does not change, check for
these problems:
 Misrouted, leaking, broken, or clogged intake air bypass control system vacuum lines.
 A cracked or damaged intake air bypass control thermal valve. Replace the valve if needed
(see page 11-351).
5. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in neutral) until the radiator fan
comes on, then let it idle.
* : This illustration shows K20Z2 engine.
08/08/21 14:31:08 61SNR030_110_0344
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
11-34511-345
Air Cleaner Removal/Installation
C B
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
6. Raise and lower the engine speed, and make sure the vacuum gauge reading does not change as the
rpm changes.
If the vacuum reading changes, check for these
problems:
 Misrouted, leaking, broken, or clogged intake air bypass control system vacuum lines.
 A cracked or damaged intake air bypass control thermal valve. Replace the valve if needed
(see page 11-351). 1. Disconnect the MAF sensor/IAT sensor 5P
connector (A).
2. Remove the bolts (B).
3. Remove the air cleaner (C).
4. Install the parts in the reverse order of removal.
* : This illustration shows K20Z2 engine.
08/08/21 14:31:08 61SNR030_110_0345
ProCarManuals.com
DYNOMITE -2009-