Engine air ACURA CSX 2006 Service Repair Manual


(#' 

)
µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
DTC P1684:
11-24811-248Electronic Throttle Control System
DTC Troubleshooting (cont’d)
9. Push the throttle valve closed as shown.
10. Release the throttle valve. Clean the throttle body (see page 11- 344),
then go to step 12 and recheck. If DTC P1683 is
indicated, go to step 11.
Go to step 11.
11. Replace the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
12. Turn the ignition switch to ON (II).
13. Reset the ECM/PCM with the HDS.
14. Do the ECM/PCM idle learn procedure (see page 11-310).
15. Turn the ignition switch to LOCK (0), and wait 10 seconds.
16. Turn the ignition switch to ON (II).
17. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3). 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
4. Turn the ignition switch to LOCK (0), and wait 10 seconds.
5. Turn the ignition switch to ON (II).
6. Check for Temporary DTCs or DTCs with the HDS.
Go to step 7.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the throttle body and the ECM/PCM.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the intake air duct from the throttle body; K20Z2 engine (see page 11-348), K20Z3
engine (see page 11-349).Throttle Valve Return Spring
Performance Problem
Does the throttle valve return?
Is DTC P1683 indicated? Is DTC P1684 indicated?
08/08/21 14:26:43 61SNR030_110_0248
ProCarManuals.com
DYNOMITE -2009-



µ´´
µ
µ
µ µ
µ
YES
NO
YES
NO
11-250Electronic Throttle Control System
DTC Troubleshooting (cont’d)
THROTTLE BODY 6P CONNECTOR
ETCSM
(GRN/YEL) ETCSM
(BLU/RED)
JUMPER WIRE ECM/PCM CONNECTOR C (44P)
ETCSM (BLU/RED)
ETCSM (GRN/YEL)
7. Turn the ignition switch to LOCK (0).
8. Disconnect the intake air duct from the throttle
body; K20Z2 engine (see page 11- 348), K20Z3
engine (see page 11-349).
9. Turn the ignition switch to ON (II).
10. Clear the DTC with the HDS.
11. Do the ETCS TEST in the INSPECTION MENU with the HDS.
12. Visually check the throttle valve operation.
Clean the throttle body (see page 11- 344),
then go to step 22 and recheck. If DTC P2101 is
indicated, go to step 19.
Go to step 13.
13. Turn the ignition switch to LOCK (0).
14. Disconnect the throttle body 6P connector.
15. Jump the SCS line with the HDS.
16. Disconnect ECM/PCM connector C (44P).
17. Connect throttle body 6P connector terminals No. 5 andNo.6withajumperwire. 18. Check for continuity between ECM/PCM connector
terminals C3 and C4.
Go to step 27.
Repair open in the wires between the throttle
body and the ECM/PCM (C3, C4), then go to step 21.
19. Turn the ignition switch to LOCK (0).
20. Replace the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
21. Reconnect all connectors.
22. Turn the ignition switch to ON (II).
23. Reset the ECM/PCM with the HDS.
24. Do the ECM/PCM idle learn procedure (see page 11-310).
Wire side of female terminals Terminal side of female terminals
Does t he t hr ot t l e v al v e oper at e smoot hl y ?
Is there continuity?
08/08/21 14:26:44 61SNR030_110_0250
ProCarManuals.com
DYNOMITE -2009-

µ´

µ´
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-252Electronic Throttle Control System
DTC Troubleshooting (cont’d)
THROTTLE BODY 6P CONNECTOR
ETCSM ETCSM
4. Disconnect the throttle body 6P connector.
5. At the throttle body side, measure the resistance
between throttle body 6P connector terminals No. 5
and No. 6 with the throttle fully closed.
Go to step 6.
Repair short in the wires between the ECM/
PCM C3 (ETCSM line) and C4 (ETCSM line),
then go to step 7.
6. Replace the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
7. Reconnect all connectors.
8. Turn the ignition switch to ON (II).
9. Reset the ECM/PCM with the HDS. 10. Do the ECM/PCM idle learn procedure (see page
11-310).
11. Turn the ignition switch to LOCK (0).
12. Turn the ignition switch to ON (II).
13. Slowly press the accelerator pedal to the floor.
14. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
15. Reconnect all connectors.
16. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
17. Turn the ignition switch to LOCK (0).
18. Turn the ignition switch to ON (II).
19. Slowly press the accelerator pedal to the floor.
20. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then go to step 17.
If the ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Terminal side of male terminals
Is t her e about 1.0 or l ess? Is DTC P2118 indicated?
Is DTC P2118 indicated?
08/08/21 14:26:44 61SNR030_110_0252
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
11-255
ECM/PCM CONNECTOR A (44P)
VCC4
(BRN)
21. Check for continuity between ECM/PCM connectorterminal A25 and body ground.
Go to step 30.
Repair open in the wire between the ECM/
PCM (A25) and the APP sensor, then go to step 24.
22. Turn the ignition switch to LOCK (0).
23. Replace the accelerator pedal module; K20Z2 engine (see page 11-269), K20Z3 engine (see page
11-270).
24. Reconnect all connectors.
25. Turn the ignition switch to ON (II).
26. Reset the ECM/PCM with the HDS.
27. Do the ECM/PCM idle learn procedure (see page 11-310).
28. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the APP sensor and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. 29. Turn the ignition switch to LOCK (0).
30. Reconnect all connectors.
31. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
32. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the APP sensor and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Terminal side of female terminals
Is there continuity?
Is DT C P2122 indicated? Is DT C P2122 indicated?
08/08/21 14:26:46 61SNR030_110_0255
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
11-259
APP SENSOR 6P CONNECTORVCC5 (GRY)
JUMPER WIRE ECM/PCM CONNECTOR A (44P)
VCC5
(GRY)
15. Turn the ignition switch to ON (II).
16. Check APP SENSOR B in the DATA LIST with theHDS.
Go to step 29.
Go to step 22.
17. Turn the ignition switch to LOCK (0).
18. Jump the SCS line with the HDS.
19. Disconnect ECM/PCM connector A (44P).
20. Connect APP sensor 6P connector terminal No. 6 to body ground with a jumper wire. 21. Check for continuity between ECM/PCM connector
terminal A24 and body ground.
Go to step 30.
Repair open in the wire between the ECM/
PCM (A24) and the APP sensor, then go to step 24.
22. Turn the ignition switch to LOCK (0).
23. Replace the accelerator pedal module; K20Z2 engine (see page 11-269), K20Z3 engine (see page
11-270).
24. Reconnect all connectors.
25. Turn the ignition switch to ON (II).
26. Reset the ECM/PCM with the HDS.
27. Do the ECM/PCM idle learn procedure (see page 11-310).
28. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the APP sensor and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
(cont’d)
Wire side of female terminals Terminal side of female terminals
Is t her e about 0.2 V or l ess?
Is there continuity?
Is DT C P2127 indicated?
08/08/21 14:26:48 61SNR030_110_0259
ProCarManuals.com
DYNOMITE -2009-


µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-261
APP SENSOR 6P CONNECTOR
SG5 (LT BLU)
JUMPER WIRE
ECM/PCM CONNECTOR A (44P) SG5 (LT BLU)
7. Turn the ignition switch to LOCK (0).
8. Jump the SCS line with the HDS.
9. Disconnect ECM/PCM connector A (44P).
10. Connect APP sensor 6P connector terminal No. 5 to body ground with a jumper wire.
11. Check for continuity between ECM/PCM connector terminal A34 and body ground.
Go to step 19.
Repair open in the wire between the ECM/
PCM (A34) and the APP sensor, then go to step 14. 12. Turn the ignition switch to LOCK (0).
13. Replace the accelerator pedal module; K20Z2
engine (see page 11-269), K20Z3 engine (see page
11-270).
14. Reconnect all connectors.
15. Turn the ignition switch to ON (II).
16. Reset the ECM/PCM with the HDS.
17. Do the ECM/PCM idle learn procedure (see page 11-310).
18. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the APP sensor and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
19. Reconnect all connectors.
20. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
21. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the APP sensor and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Wire side of female terminals
Terminal side of female terminals
Is there continuity? Is DT C P2128 indicated?
Is DT C P2128 indicated?
08/08/21 14:26:49 61SNR030_110_0261
ProCarManuals.com
DYNOMITE -2009-


(#' 

)
µ
µ
µ
µ µ
µ
DTC P2135:
YES
NO
YES
NO YES
NO
11-262Electronic Throttle Control System
DTC Troubleshooting (cont’d)
ECM/PCM CONNECTOR C (44P)
TPSB (RED/BLU)
TPSA
(RED/BLK)
TP Sensor A/B Incorrect Voltage
Correlation
Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3). 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Do the ETCS TEST in the INSPECTION MENU with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the throttle body and the ECM/PCM.
5. Turn the ignition switch to LOCK (0).
6. Disconnect the intake air duct from the throttle body; K20Z2 engine (see page 11- 348), K20Z3
engine (see page 11-349).
7. Turn the ignition switch to ON (II).
8. Visually check the throttle valve operation while you clear the DTC with the HDS.
Go to step 15.
Go to step 9. 9. Turn the ignition switch to LOCK (0).
10. Jump the SCS line with the HDS.
11. Disconnect ECM/PCM connector C (44P).
12. Check for continuity between ECM/PCM connector terminals C20 and C21.
Go to step 13.
Go to step 22.
Terminal side of female terminals
Is DTC P2135 indicated?
Does the valve temporarily move to its f ullycl osed posi t i on? Is there continuity?
08/08/21 14:26:49 61SNR030_110_0262
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
11-263
ECM/PCM CONNECTOR C (44P)
TPSB (RED/BLU)
TPSA
(RED/BLK)
13. Disconnect the throttle body 6P connector.
14. Check for continuity between ECM/PCM connector terminals C20 and C21.
Repair short in the wires between ECM/PCM
connector terminals C20 (TPSA line) and C21 (TPSB
line),thengotostep17.
Go to step 15.
15. Turn the ignition switch to LOCK (0).
16. Replace the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
17. Reconnect all connectors.
18. Turn the ignition switch to ON (II).
19. Reset the ECM/PCM with the HDS.
20. Do the ECM/PCM idle learn procedure (see page 11-310).
21. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM,
then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. 22. Reconnect all connectors.
23. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
24. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then recheck. If the
ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Terminal side of female terminals
Is there continuity?
Is DTC P2135 indicated? Is DTC P2135 indicated?
08/08/21 14:26:49 61SNR030_110_0263
ProCarManuals.com
DYNOMITE -2009-


(#' 

)
µ´
µ
µ µ
µ
µ
µ
DTC P2176:
YES
NO YES
NO
YES
NO
11-266Electronic Throttle Control System
DTC Troubleshooting (cont’d)
THROTTLE BODY 6P CONNECTOR
ETCSM
(GRN/YEL) ETCSM
(BLU/RED)
JUMPER WIRE
Throttle Actuator Control System
Idle Position Not Learned
Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
NOTE:  Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If DTC P2135 is stored at the same time as DTC P2176, troubleshoot DTC P2135 first, then recheck for DTC
P2176.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0).
4. Turn the ignition switch to ON (II), and wait 10 seconds.
5. Check for Temporary DTCs or DTCs with the HDS.
Go to step 6.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the throttle body and the ECM/PCM, then clean
the throttle body (see page 11- 344).
6. Turn the ignition switch to LOCK (0).
7. Disconnect the intake air duct from the throttle body; K20Z2 engine (see page 11- 348), K20Z3
engine (see page 11-349).
8. Turn the ignition switch to ON (II).
9. Clear the DTC with the HDS. 10. Visually check the throttle valve operation while
doing the ETCS TEST in the INSPECTION MENU
with the HDS.
Go to step 11.
Go to step 12.
11. Check for sludge or carbon on the throttle valve.
Clean the throttle body (see page 11-344),
then go to step 21 and recheck.
Go to step 18.
12. Turn the ignition switch to LOCK (0).
13. Disconnect the throttle body 6P connector.
14. Jump the SCS line with the HDS.
15. Disconnect ECM/PCM connector C (44P).
16. Connect throttle body 6P connector terminals No. 5 andNo.6withajumperwire.
Wire side of female terminals
Is DTC P2176 indicated? Does the throttle valve move to its f ully closed
posi t i on?
Is there sludge or carbon on the throttle valve?
08/08/21 14:26:50 61SNR030_110_0266
ProCarManuals.com
DYNOMITE -2009-


µ´
µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-267
ECM/PCM CONNECTOR C (44P)
ETCSM (GRN/YEL) ETCSM (BLU/RED)
17. Check for continuity between ECM/PCM connector terminals C3 and C4.
Go to step 27.
Repair open in the wires between the throttle
body and the ECM/PCM (C3, C4), then go to step 20.
18. Turn the ignition switch to LOCK (0).
19. Replace the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
20. Reconnect all connectors.
21. Turn the ignition switch to ON (II).
22. Reset the ECM/PCM with the HDS.
23. Do the ECM/PCM idle learn procedure (see page 11-310).
24. Turn the ignition switch to LOCK (0).
25. Turn the ignition switch to ON (II), and wait 10 seconds. 26. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM,
then clean the throttle body (see page 11-344), and
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
27. Reconnect all connectors.
28. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
29. Turn the ignition switch to LOCK (0).
30. Turn the ignition switch to ON (II), and wait 10 seconds.
31. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then go to step 29.
If the ECM/PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Terminal side of female terminals
Is there continuity? Is DTC P2176 indicated?
Is DTC P2176 indicated?
08/08/21 14:26:50 61SNR030_110_0267
ProCarManuals.com
DYNOMITE -2009-